Concept explainers
A mass of 10 g of nitrogen is contained in the spring-loaded piston–cylinder device shown in Fig. P4–54. The spring constant is 1 kN/m, and the piston diameter is 10 cm. When the spring exerts no force against the piston, the nitrogen is at 120 kPa and 27°C. The device is now heated until its volume is 10 percent greater than the original volume. Determine the change in the specific internal energy and enthalpy of the nitrogen.
FIGURE P4–54
The change in the internal energy of the nitrogen.
The change in the enthalpy of the nitrogen.
Answer to Problem 54P
The change in the internal energy of the nitrogen is
The change in the enthalpy of the nitrogen is
Explanation of Solution
Write the expression for the initial volume of nitrogen.
Here, the mass of the spring loaded piston cylinder device is
Determine the linear P-v process for spring loaded piston cylinder device.
Here, the system pressure is
Determine the specific heat constant value.
Substitute
From the Equation (IV), the final volume is 10 percent greater than the original volume;
Determine the final temperature of the nitrogen.
Here, the final pressure of the nitrogen is
Determine the internal energy of the spring loaded piston-cylinder device.
Here, the specific heat of constant volume is
Determine the enthalpy of the spring loaded piston-cylinder device.
Here, the specific heat of constant pressure is
Conclusion:
Write the conversion of unit for temperature of 20 C from
Refer Table A-2(a), “Ideal-gas specific heats of various common gases” to obtain the value of gas constant, specific heat of constant volume and pressure for nitrogen gas is
Substitute
Substitute
Substitute
Substitute
Substitute
Thus, the change in the internal energy of the nitrogen is
Substitute
Thus, the change in the enthalpy of the nitrogen is
Want to see more full solutions like this?
Chapter 4 Solutions
THERMODYNAMICS: ENG APPROACH LOOSELEAF
- THERMOFLUID A frictionless piston-cylinder contains 3.30 kg of saturated water at 1 MPa. The water is expanded at constant pressure until its temperature rises to 270 °C. The image of the system and process are shown in Figure 3. Determine: The final volume of water in cylinder, and sketch the process in P-V diagramarrow_forwardWater is contained in a cylinder/piston arrangement fitted with upper stops which limit the volume to 0.2 m maximum. The mass of the water is 0.26 kg, and the weight of the piston and the atmospheric pressure are balanced when the internal pressure is 200kPa. Initially, the piston pushes against the upper stops, and the pressure is 400 kPa. The water is allowed to slowly cool down to a temperature of 110°C. Sketch the process on both the P-v and the T-v diagrams. Label all relevant points and assignarrow_forwardA piston–cylinder device contains 0.85 kg of refrigerant- 134a at 210ºC. The piston that is free to move has a mass of 12 kg and a diameter of 25 cm. The local atmospheric pressure is 88 kPa. Now, heat is transferred to refrigerant-134a until the temperature is 15ºC. Determine: (a) the final pressure,(b) the change in the volume of the cylinder, and (c) the change in the enthalpy of the refrigerant-134a.arrow_forward
- 0.2 m^3 of an ideal gas at a pressure of 2Mpa and 600 k is expanded isothermally to 5 times the initial volume. It is then cooled to 300 K at constant Volume and then compressed back polytropically to its initial state. Show the process on a P-V diagram and determine the work done.arrow_forwardThe spring-loaded piston–cylinder device shown in Fig. P3–63 is filled with 0.5 kg of water vapor that is initially at 4 MPa and 400°C. Initially, the spring exerts no force against the piston. The spring constant in the spring force relation F = kx is k = 0.9 kN/cm and the piston diameter is D = 20 cm. The water now undergoes a process until its volume is one-half of the original volume. Calculate the final temperature and the specific enthalpy of the water.arrow_forward3. A piston-cylinder device contains .85 kg of refrigerant-R134a at -10 °C. The piston that is free to move has a mass of 12 kg and a diameter of 25 cm. The local atmospheric pressure is 88 kPa. Now, heat is transferred to refrigerant-134a until the temperature is 15°C. Determine (a) the final pressure, (b) the change in the volume of the cylinder, and (c) the change in the enthalpy of the refrigerant-134a. R-134a 0.85 kg -10°Carrow_forward
- A 0.8-m3 rigid tank contains nitrogen gas at 600 kPa and 300 K. Now the gas is compressed isothermally to a volume of 0.1 m3. Solve for the work done on the gas during this compression process.arrow_forwardA frictionless piston-cylinder device initially contains 200L of saturated liquid refrigerant-134a. The piston is free to move and its mass is such that it maintains a pressure of 900 kPa on the refrigerant. The refrigerant is now heated until its temperature rises to 70C. Calculate the work done during this process. ANS. 5571 KJA fixed mass of an ideal gas is heated from 50 to 80°C at a constant pressure of (a) 1 atm and (b) 3 atm. For which case do you think the energy required will be greater?arrow_forwardA mass of 0.1 kg of helium fills a 0.2 m³ rigid vessel at 350 kPa. The vessel is heated until the pressure is 710 kPa. Calculate the temperature change of helium (in K) as a result of this heating. The gas constant of helium is R= 2.0769 kPa-m3/kg-K. Helium 0.1 kg 0.2 m 350 kPa The temperature change is K.arrow_forward
- A spring-loaded piston-cylinder device contains 100 g of helium as the system, as shown in the figure. The system undergoes a process from 115 kPa and 0.8739 m3 to 550 kPa and 0.3832 m³. Determine the (a) work done, (b) heat transfer in this process. The properties of helium are R= 2.08 kJ/kg-K and cy= 3.16 kJ/kg-K. Also, determine the (c) initial temperature and (d) final temperature of helium. - Spring Helium The work done in this process is The heat transfer in this process is| The initial temperature of helium is The final temperature of helium is kJ. kJ. °С. °C.arrow_forwardThe piston-cylinder system shown above contains R-410a at 20°C and 100 kPa. If the temperature of the R-410a is increased to 50°C the specific volume in the piston-cylinder is ?arrow_forwardA gas at a pressure of 1.4MN/m2 and temperature of 360 degrees is expanded adiabatically to a pressure of 100KN/m2 the gas is then heated at constant volume until it again attains 360 degree Celsius when its pressure is found to be 220KN/m2 and finally it is compressed isothermally until the original pressure of 1.4MN/m2 is attained sketch the p-v diagram for these process and if the gas has a mass of 0.23kg, determine; The valve of the adiabatic index y The change in internal energy during the adiabatic expansion Taking Cp for the gas as 1.005KJ/kgkarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY