THERMODYNAMICS: ENG APPROACH LOOSELEAF
THERMODYNAMICS: ENG APPROACH LOOSELEAF
9th Edition
ISBN: 9781266084584
Author: CENGEL
Publisher: MCG
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 4.5, Problem 44P

Two tanks (Tank A and Tank B) are separated by a partition. Initially Tank A contains 2 kg of steam at 1 MPa and 300°C while Tank B contains 3 kg of saturated liquid–vapor mixture at 150°C with a vapor mass fraction of 50 percent. The partition is now removed and the two sides are allowed to mix until mechanical and thermal equilibrium are established. If the pressure at the final state is 300 kPa, determine (a) the temperature and quality of the steam (if mixture) at the final state and (b) the amount of heat lost from the tanks.

FIGURE P4–44

Chapter 4.5, Problem 44P, Two tanks (Tank A and Tank B) are separated by a partition. Initially Tank A contains 2 kg of steam

(a)

Expert Solution
Check Mark
To determine

The final temperature of the steam for a tank.

The quality of the steam at the final state for a tank.

Answer to Problem 44P

The final temperature of the steam is 133.5°C_.

The quality of the steam at the final state is 0.3641_.

Explanation of Solution

Write the expression for the energy balance equation.

EinEout=ΔEsystem (I)

Here, the total energy entering the system is Ein, the total energy leaving the system is Eout, and the change in the total energy of the system is ΔEsystem.

Simplify Equation (I) and write energy balance relation of two tanks.

WinQout=ΔU (II)

Here, the boundary work to be done into the system is Win, the heat to be transfer by the system is Qout, and the change in the internal energy is ΔU.

Substitute 0 for Win in Equation (II)

0Qout=ΔUA+ΔUBQout=[m(u2u1)]A+[m(u2u1)]B (III)

Here, the initial mass of tank A is mA, the initial specific internal energy of tank A is uA, the initial mass of tank B is mB, the initial specific internal energy of tank B is uB, the final mass of tank A is mA, the final specific internal energy of tank A is uA, the final mass of tank B is mB, and the final specific internal energy of tank B is uB.

Write the expression for volume of tank A.

νA=mAv1,A (IV)

Here, the volume of the tank A is νA and the initial specific volume of tank A is v1,A.

Write the expression for volume of tank B.

νB=mBv1,B (V)

Here, the volume of the tank B is νB and the initial specific volume of tank B is v1,B.

Write the expression for total mass of tank.

m=mA+mB (VI)

Write the expression for total volume contained in both tanks.

ν=νA+νB (VII)

Write the expression for final specific volume of tank.

v2=νm (VIII)

Conclusion:

Convert the unit of pressure from kPa to MPa.

P=1000kPa=1000kPa×103MPakPa=1.0MPa

From the Table A-6, “Superheated water”, obtain the value of initial specific volume (v1,A) and specific internal energy (u1,A) for tank A at the initial pressure of tank A of 1.0 MPa and temperature of tank A of 300 C.

v1,A=0.25799m3/kg.

u1,A=2793.7kJ/kg.

From the Table A-4, “Superheated water”, obtain the value of initial specific volume and specific internal energy for tank B.

At the initial temperature and quality of the steam at the final state of tank B as 150 C and 0.50.

vf=0.001091m3/kg.

vg=0.39248m3/kg.

uf=631.66kJ/kg.

ufg=1927.4kJ/kg.

Determine the specific volume of a two-phase system for tank B.

v1,A=vf+xvfg=vf+x(vgvf) (IX)

Here, the specific volume of saturated liquid for tank B is vf, the specific volume of saturated vapour for tank B  is vg, the specific volume change upon vaporization for tank B is vfg, and the quality of final state for tank B is x.

u1,A=uf+xufg (X)

Here, the specific internal energy of saturated liquid for tank B is uf and the specific internal energy change upon vaporization for tank B is ufg.

Substitute 0.001091m3/kg for vf, 0.50 for x, and 0.39248m3/kg for vg in Equation (IX)

v1,B=(0.001091m3/kg)+(0.50)(0.39248m3/kg0.001091m3/kg)=(0.001091m3/kg)+(0.50)(0.391389m3/kg)=0.196786m3/kg0.19679m3/kg

Substitute 631.66kJ/kg for uf 0.50 for x, and 1927.4kJ/kg for ufg in Equation (X).

u1,B=(631.66kJ/kg)+(0.50)(1927.4kJ/kg)=(631.66kJ/kg)+(963.7kJ/kg)=1595.36kJ/kg

Substitute 2kg for mA and 0.25799m3/kg for v1,A in Equation (IV).

νA=(2kg)×(0.25799m3/kg)=0.51598m3

Substitute 3kg for mB and 0.19679m3/kg for v1,B in Equation (V).

νB=(3kg)×(0.19679m3/kg)=0.59037m3

Substitute 2kg for mA and 3kg for mB in Equation (VI).

m=2kg+5kg=5kg

Substitute 0.51598m3 for νA and 0.59037m3 for νB in Equation (VIII).

ν=(0.51598m3)+(0.59037m3)=1.106m3

Substitute 1.106m3 for ν and 5kg for m in Equation (X).

v2=1.106m35kg=0.22127m3/kg

Refer Table A-5, “Saturated water-pressure”, obtain the final temperature of the steam.

At final pressure of the steam is 133.5°C.

Thus, the final temperature of the steam is 133.5°C_.

From the Table A-5, “Saturated water-pressure”, obtain the value of quality of the steam at the final state and final specific internal energy for tank B.

At the final pressure and specific volume at the final state as 300 kPa and 0.22127m3/kg.

vf=0.001073m3/kg.

vg=0.60582m3/kg.

uf=561.11kJ/kg.

ufg=1982.1kJ/kg.

Determine the specific volume of a two-phase system for steam.

ν2=vf+x2(vgvf)x2=ν2vfvgvf (XI)

Here, the specific volume of saturated liquid for steam is vf, the specific volume of saturated vapour for steam is vg, and the quality of final state for steam is x2.

u2=uf+x2ufg (XII)

Here, the specific internal energy of saturated liquid for steam is uf and the specific internal energy change upon vaporization for steam is ufg.

Substitute 0.001073m3/kg for vf, 0.22127m3/kg for ν2, and 0.60582m3/kg for vg in Equation (XI)

x2=(0.22127m3/kg0.001073m3/kg)(0.60582m3/kg0.001073m3/kg)=0.220197m3/kg0.604747m3/kg=0.3641

Thus, the quality of the steam at the final state is 0.3641_.

Substitute 561.11kJ/kg for uf 0.3641 for x2, and 1982.1kJ/kg for ufg in Equation (XII).

u2=(561.11kJ/kg)+(0.3641)×(1982.1kJ/kg)=(561.11kJ/kg)+(721.68kJ/kg)=1282.79kJ/kg1282.8kJ/kg

(b)

Expert Solution
Check Mark
To determine

The amount of heat lost from the tanks.

Answer to Problem 44P

The amount of heat lost from the tanks is 3959kJ_.

Explanation of Solution

Conclusion:

Substitute 2kg for mA, 1282.8kJ/kg for u2,A, 2793.7kJ/kg for u1,A, 3kg for mB, 1282.8kJ/kg for u2,B, and 1595.4kJ/kg for u1,B in Equation (III).

Qout=[(2kg)(1282.8kJ/kg2793.7kJ/kg)]A+[(3kg)(1282.8kJ/kg1595.4kJ/kg)]BQout=[(2kg)(1510.9kJ/kg)]A+[(3kg)(312.6kJ/kg)]BQout=[(3021kJ)+(937.8kJ)]Qout=3959.6kJ           Qout=3959.6kJQout=3959.6kJ

Thus, the amount of heat lost from the tanks is 3959kJ_.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
A frictionless piston cylinder device contains 3 L of saturated liquid water at a temperature of 110°C. Water is stirred by a paddle wheel for 22 minutes while a current of 7.5 A flows through a resistor placed in the water. If the 74% of the water remains at the liquid phase and the rest water is evaporated during this constant pressure process. If the voltage of the electricity source is 160 volts, determine (a) the initial pressure and (b) the amount of work added to the water by the paddle wheel. Also, show the process on a P-v diagram with respect to saturation lines. H2O P= constant We sh
A frictionless piston-cylinder device contains 3 L of saturated liquid water at a pressure of 200 kPa. Water is stirred by a paddle wheel for 22 minutes while a current of 7.5 A flows through a resistor placed in the water. If the 74% of the water remains at the liquid phase and the rest water is evaporated during this constant pressure process. If the voltage of the electricity source is 160 volts, determine (a) the final temperature and (b) the amount of work added to the water by the paddle wheel. Also, show the process on a P-v diagram with respect to saturation lines. H20 P constant W.
A 1-m3 tank containing air at 25'C and 500 kPa is connected through a valve to another tank containing 5 kg of air at 35'C and 200 kPa. Now the valve is opened, and the entire system is allowed to reach thermal equilibrium with the surroundings, which are at 20°C. Determine the volume of the second tank and the final equilibrium pressure of air.

Chapter 4 Solutions

THERMODYNAMICS: ENG APPROACH LOOSELEAF

Ch. 4.5 - 1 m3 of saturated liquid water at 200C is expanded...Ch. 4.5 - Argon is compressed in a polytropic process with n...Ch. 4.5 - A gas is compressed from an initial volume of 0.42...Ch. 4.5 - A mass of 1.5 kg of air at 120 kPa and 24C is...Ch. 4.5 - During some actual expansion and compression...Ch. 4.5 - A frictionless pistoncylinder device contains 5 kg...Ch. 4.5 - During an expansion process, the pressure of a gas...Ch. 4.5 - A pistoncylinder device initially contains 0.4 kg...Ch. 4.5 - A pistoncylinder device contains 0.15 kg of air...Ch. 4.5 - Determine the boundary work done by a gas during...Ch. 4.5 - 1 kg of water that is initially at 90C with a...Ch. 4.5 - An ideal gas undergoes two processes in a...Ch. 4.5 - A pistoncylinder device contains 50 kg of water at...Ch. 4.5 - Prob. 26PCh. 4.5 - A closed system like that shown in Fig. P427E is...Ch. 4.5 - A rigid container equipped with a stirring device...Ch. 4.5 - Complete each line of the following table on the...Ch. 4.5 - A substance is contained in a well-insulated rigid...Ch. 4.5 - A 0.5-m3rigid tank contains refrigerant-134a...Ch. 4.5 - A 20-ft3 rigid tank initially contains saturated...Ch. 4.5 - A rigid 10-L vessel initially contains a mixture...Ch. 4.5 - A rigid 1-ft3 vessel contains R-134a originally at...Ch. 4.5 - A pistoncylinder device contains 5 kg of...Ch. 4.5 - A pistoncylinder device contains 0.5 lbm of water...Ch. 4.5 - 2 kg of saturated liquid water at 150C is heated...Ch. 4.5 - An insulated pistoncylinder device contains 5 L of...Ch. 4.5 - A 40-L electrical radiator containing heating oil...Ch. 4.5 - Steam at 75 kPa and 8 percent quality is contained...Ch. 4.5 - A pistoncylinder device initially contains 0.6 m3...Ch. 4.5 - An insulated tank is divided into two parts by a...Ch. 4.5 - Two tanks (Tank A and Tank B) are separated by a...Ch. 4.5 - Is the energy required to heat air from 295 to 305...Ch. 4.5 - A fixed mass of an ideal gas is heated from 50 to...Ch. 4.5 - A fixed mass of an ideal gas is heated from 50 to...Ch. 4.5 - A fixed mass of an ideal gas is heated from 50 to...Ch. 4.5 - Is the relation u = mcv,avgT restricted to...Ch. 4.5 - Is the relation h = mcp,avgT restricted to...Ch. 4.5 - What is the change in the internal energy, in...Ch. 4.5 - Neon is compressed from 100 kPa and 20C to 500 kPa...Ch. 4.5 - What is the change in the enthalpy, in kJ/kg, of...Ch. 4.5 - A mass of 10 g of nitrogen is contained in the...Ch. 4.5 - Determine the internal energy change u of...Ch. 4.5 - Determine the enthalpy change h of oxygen, in...Ch. 4.5 - Is it possible to compress an ideal gas...Ch. 4.5 - Nitrogen in a rigid vessel is cooled by rejecting...Ch. 4.5 - Nitrogen at 100 psia and 300F in a rigid container...Ch. 4.5 - A pistoncylinder device containing carbon-dioxide...Ch. 4.5 - A 3-m3 rigid tank contains hydrogen at 250 kPa and...Ch. 4.5 - 1 kg of oxygen is heated from 20 to 120C....Ch. 4.5 - A 10-ft3 tank contains oxygen initially at 14.7...Ch. 4.5 - A 4-m 5-m 7-m room is heated by the radiator of...Ch. 4.5 - An insulated rigid tank is divided into two equal...Ch. 4.5 - An ideal gas contained in a pistoncylinder device...Ch. 4.5 - A 4-m 5-m 6-m room is to be heated by a...Ch. 4.5 - An insulated pistoncylinder device initially...Ch. 4.5 - Argon is compressed in a polytropic process with n...Ch. 4.5 - An insulated pistoncylinder device contains 100 L...Ch. 4.5 - Air is contained in a variable-load pistoncylinder...Ch. 4.5 - A mass of 15 kg of air in a pistoncylinder device...Ch. 4.5 - Prob. 73PCh. 4.5 - A pistoncylinder device contains 2.2 kg of...Ch. 4.5 - A pistoncylinder device contains 4 kg of argon at...Ch. 4.5 - A spring-loaded pistoncylinder device contains 5...Ch. 4.5 - Prob. 78PCh. 4.5 - Prob. 79PCh. 4.5 - A 1-kg block of iron is heated from 25 to 75C....Ch. 4.5 - The state of liquid water is changed from 50 psia...Ch. 4.5 - During a picnic on a hot summer day, all the cold...Ch. 4.5 - An ordinary egg can be approximated as a...Ch. 4.5 - Consider a 1000-W iron whose base plate is made of...Ch. 4.5 - Stainless steel ball bearings ( = 8085 kg/m3 and...Ch. 4.5 - In a production facility, 1.6-in-thick 2-ft 2-ft...Ch. 4.5 - Long cylindrical steel rods ( = 7833 kg/m3 and cp...Ch. 4.5 - An electronic device dissipating 25 W has a mass...Ch. 4.5 - Prob. 90PCh. 4.5 - Prob. 91PCh. 4.5 - Is the metabolizable energy content of a food the...Ch. 4.5 - Is the number of prospective occupants an...Ch. 4.5 - Prob. 94PCh. 4.5 - Prob. 95PCh. 4.5 - Prob. 96PCh. 4.5 - Consider two identical 80-kg men who are eating...Ch. 4.5 - A 68-kg woman is planning to bicycle for an hour....Ch. 4.5 - A 90-kg man gives in to temptation and eats an...Ch. 4.5 - A 60-kg man used to have an apple every day after...Ch. 4.5 - Consider a man who has 20 kg of body fat when he...Ch. 4.5 - Consider two identical 50-kg women, Candy and...Ch. 4.5 - Prob. 103PCh. 4.5 - Prob. 104PCh. 4.5 - Prob. 105PCh. 4.5 - Prob. 106PCh. 4.5 - Prob. 107PCh. 4.5 - Prob. 108PCh. 4.5 - Prob. 109RPCh. 4.5 - Prob. 110RPCh. 4.5 - Prob. 111RPCh. 4.5 - Prob. 112RPCh. 4.5 - Prob. 113RPCh. 4.5 - Consider a pistoncylinder device that contains 0.5...Ch. 4.5 - Prob. 115RPCh. 4.5 - Air in the amount of 2 lbm is contained in a...Ch. 4.5 - Air is expanded in a polytropic process with n =...Ch. 4.5 - Nitrogen at 100 kPa and 25C in a rigid vessel is...Ch. 4.5 - Prob. 119RPCh. 4.5 - A mass of 3 kg of saturated liquidvapor mixture of...Ch. 4.5 - A mass of 12 kg of saturated refrigerant-134a...Ch. 4.5 - Prob. 122RPCh. 4.5 - A pistoncylinder device contains helium gas...Ch. 4.5 - Prob. 124RPCh. 4.5 - Prob. 125RPCh. 4.5 - Prob. 126RPCh. 4.5 - Prob. 127RPCh. 4.5 - Water is boiled at sea level in a coffeemaker...Ch. 4.5 - The energy content of a certain food is to be...Ch. 4.5 - Prob. 130RPCh. 4.5 - An insulated pistoncylinder device initially...Ch. 4.5 - An insulated rigid tank initially contains 1.4 kg...Ch. 4.5 - In order to cool 1 ton of water at 20C in an...Ch. 4.5 - A 0.3-L glass of water at 20C is to be cooled with...Ch. 4.5 - A well-insulated 3-m 4m 6-m room initially at 7C...Ch. 4.5 - Prob. 137RPCh. 4.5 - Prob. 138RPCh. 4.5 - Prob. 140RPCh. 4.5 - A pistoncylinder device initially contains 0.35 kg...Ch. 4.5 - Two 10-ft3 adiabatic tanks are connected by a...Ch. 4.5 - Prob. 143RPCh. 4.5 - Prob. 144RPCh. 4.5 - A 3-m3 rigid tank contains nitrogen gas at 500 kPa...Ch. 4.5 - A 0.5-m3 rigid tank contains nitrogen gas at 600...Ch. 4.5 - A well-sealed room contains 60 kg of air at 200...Ch. 4.5 - A room contains 75 kg of air at 100 kPa and 15C....Ch. 4.5 - Prob. 149FEPCh. 4.5 - A pistoncylinder device contains 5 kg of air at...Ch. 4.5 - Prob. 151FEPCh. 4.5 - A 2-kW electric resistance heater submerged in 5...Ch. 4.5 - Prob. 153FEPCh. 4.5 - 1.5 kg of liquid water initially at 12C is to be...Ch. 4.5 - Prob. 155FEPCh. 4.5 - An ordinary egg with a mass of 0.1 kg and a...Ch. 4.5 - Prob. 157FEPCh. 4.5 - A 6-pack of canned drinks is to be cooled from 18C...Ch. 4.5 - Prob. 159FEPCh. 4.5 - An ideal gas has a gas constant R = 0.3 kJ/kgK and...Ch. 4.5 - A pistoncylinder device contains an ideal gas. The...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
What is entropy? - Jeff Phillips; Author: TED-Ed;https://www.youtube.com/watch?v=YM-uykVfq_E;License: Standard youtube license