Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 44, Problem 10ASRQ
While discussing automatic AWD systems: Technician A says that the systems operate in 2WD nearly all of the time. Technician B says that on many systems, when the PCM receives inputs from the CAN bus, it indicates that wheel slippage power is sent to the other drive axle. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says that the front wheel bearings on atypical FWD car are pressed in and out of the steeringknuckle assembly. Technician B says that the frontwheel bearings on a typical FWD may be bolted intothe steering knuckle. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor B
Technician A says that on FWD vehicles, the front wheels toe-out while the rear wheels on an independent suspension try to toe-in as the vehicle moves ahead. Technician B says that on RWD vehicles, the front wheels tend to toe-in while the rear wheels toe-out in response to rolling resistance as suspension compliance. Who is correct?
While diagnosing a complaint of excessive play in the steering on a vehicle with power steering: Technician A says that the problem could be caused by air in the system. Technician B says that the problem could be caused by a worn steering shaft U-joint. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Chapter 44 Solutions
Automotive Technology
Ch. 44 - Name the three main driveline components that are...Ch. 44 - Describe the purpose of a viscous clutch.Ch. 44 - What is the purpose of the interaxle differential?Ch. 44 - Briefly explain how a Haldex clutch works.Ch. 44 - What is the primary purpose of a transfer case?Ch. 44 - Prob. 6SACh. 44 - When the plates of a viscous coupling (clutch)...Ch. 44 - How does a viscous clutch assembly work? Why is it...Ch. 44 - What results from having different axle ratios on...Ch. 44 - The transfer clutch in the all-wheel drive...
Ch. 44 - In a viscous clutch, when the silicone fluid is...Ch. 44 - When servicing transfer cases, all of the...Ch. 44 - Prob. 5MCCh. 44 - Which of the following would not cause noise while...Ch. 44 - Which of the following could cause the 4WD...Ch. 44 - Technician A says that viscous couplings are...Ch. 44 - Technician A says that some AWD systems have a...Ch. 44 - While discussing AWD systems: Technician A says...Ch. 44 - Prob. 4ASRQCh. 44 - While diagnosing the cause of noise from a...Ch. 44 - Technician A says that a seized shift linkage may...Ch. 44 - While diagnosing the cause of the transfer case...Ch. 44 - While servicing an AWD vehicle: Technician A...Ch. 44 - While discussing the various speed gear positions...Ch. 44 - While discussing automatic AWD systems: Technician...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 32. Technician A says hypoid gearset are only used in RWD vehicle drivetrains. Technician B says hypoid gearset multiply torque. Which technician is correct? A- Technician A B- Technician B C- Both A and B D- Neither A nor B.arrow_forwardThe typical RWD drive shaft rotates how many times faster than wheelsarrow_forwardWhat results from having different axle ratios on thefront and rear of a 4WD vehicle when it is operatingin 4WD?a. Poor handling on dry surfacesb. Driveline windupc, Mechanical damage to the drivelined. All of the abovearrow_forward
- Technician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?arrow_forwardWhen discussing the possible causes for a shudder during acceleration, Technician A says that a worn inner CV joint could be the cause. Technician B says that insufficient differential gear backlash could be the cause of the problem. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forwardName the three main driveline components that are added to a RWD vehicle to make it a 4WD vehicle.arrow_forward
- 2. Technician A says that the purpose of the steering wheel holder is to make sure that the steeringwheel is centered after the alignment. Technician B says that if the steering wheel is not centered after an alignment, it should be pulled offthe column and positioned correctly. Who iscorrect?a. Technician A c. Both A and B b. Technician B d. Neither A nor Barrow_forwardTech A says that the purpose of a steering wheel holder is to make sure that the steering wheel is centered after the alignment. Tech B says that if the steering wheel is not centered after an alignment, it should be pulled off the column and positioned correctly. Who is correctarrow_forwardTechnician A says that play in the steering gear is the probable cause of a shimmy. Technician B says that it could be loose steering linkage. Who is correct?arrow_forward
- Technician A says that a malfunction of the ABS causes the control module to shut off or inhibit the system. Technician B says that a loss of hydraulic fluid or power booster pressure disables the antilock brake system. Who is correct? a. Technician A only b.Technician B only c.Both A and B d.Neither A nor Barrow_forwardWhen discussing shift problems, Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. Technician B that poor shift boot alignment can cause a transaxle to jump out of gear. says Who is correct? A. A only C. Both A and B B. B only D. Neither A nor Barrow_forwardTechnician A says that throttle position is an important input in most electronic shift control systems. Technician B says that vehicle speed is an important input for most electronic shift control systems. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
The Robot Revolution: The New Age of Manufacturing | Moving Upstream; Author: Wall Street Journal;https://www.youtube.com/watch?v=HX6M4QunVmA;License: Standard Youtube License