Concept explainers
For the boom and loading shown, determine (a) the tension in cord BD, (b) the reaction at C.
Fig.P4.71
(a)

The tension in the cord
Answer to Problem 4.71P
The tension in the cord
Explanation of Solution
Calculation:
If the rigid body subjected to three forces, such a body is commonly called a three-force body. If a two force body is in equilibrium the lines of action of the three forces must be either concurrent or parallel.
The figure 1 represents the free body diagram of the system.
Write the expression for the angle
Here,
Write the expression for the angle
Write the relations connecting the sides of the triangle.
Figure 2 represents a force triangle as shown in the above figure with its interior angles computed from the known directions of the forces. Then use the law of sines to find the unknown forces.
Write the expression for the law of sines from the force triangle.
Conclusion:
Substitute
Substitute
Substitute
Substitute
On rearranging the above equation to find
Therefore, the tension in the cord
(b)

The reaction at
Answer to Problem 4.71P
The reaction at
Explanation of Solution
Calculation:
If the rigid body subjected to three forces, such a body is commonly called a three-force body. If a two force body is in equilibrium the lines of action of the three forces must be either concurrent or parallel.
Write the expression for the angle
Here,
Write the expression for the angle
Write the relations connecting the sides of the triangle.
Figure 2 represents a force triangle as shown in the above figure with its interior angles computed from the known directions of the forces. Then use the law of sines to find the unknown forces.
Write the expression for the law of sines from the force triangle.
Conclusion:
Substitute
Substitute
Substitute
Substitute
On rearranging the above equation to find
Therefore, reaction at
Want to see more full solutions like this?
Chapter 4 Solutions
VECTOR MECHANICS FOR ENGINEERS: STATICS
- (read image) (answer given)arrow_forwardA cylinder and a disk are used as pulleys, as shown in the figure. Using the data given in the figure, if a body of mass m = 3 kg is released from rest after falling a height h 1.5 m, find: a) The velocity of the body. b) The angular velocity of the disk. c) The number of revolutions the cylinder has made. T₁ F Rd = 0.2 m md = 2 kg T T₂1 Rc = 0.4 m mc = 5 kg ☐ m = 3 kgarrow_forward(read image) (answer given)arrow_forward
- 11-5. Compute all the dimensional changes for the steel bar when subjected to the loads shown. The proportional limit of the steel is 230 MPa. 265 kN 100 mm 600 kN 25 mm thickness X Z 600 kN 450 mm E=207×103 MPa; μ= 0.25 265 kNarrow_forwardT₁ F Rd = 0.2 m md = 2 kg T₂ Tz1 Rc = 0.4 m mc = 5 kg m = 3 kgarrow_forward2. Find a basis of solutions by the Frobenius method. Try to identify the series as expansions of known functions. (x + 2)²y" + (x + 2)y' - y = 0 ; Hint: Let: z = x+2arrow_forward
- 1. Find a power series solution in powers of x. y" - y' + x²y = 0arrow_forward3. Find a basis of solutions by the Frobenius method. Try to identify the series as expansions of known functions. 8x2y" +10xy' + (x 1)y = 0 -arrow_forwardHello I was going over the solution for this probem and I'm a bit confused on the last part. Can you please explain to me 1^4 was used for the Co of the tubular cross section? Thank you!arrow_forward
- Blood (HD = 0.45 in large diameter tubes) is forced through hollow fiber tubes that are 20 µm in diameter.Equating the volumetric flowrate expressions from (1) assuming marginal zone theory and (2) using an apparentviscosity for the blood, estimate the marginal zone thickness at this diameter. The viscosity of plasma is 1.2 cParrow_forwardQ2: Find the shear load on bolt A for the connection shown in Figure 2. Dimensions are in mm Fig. 2 24 0-0 0-0 A 180kN (10 Markarrow_forwarddetermine the direction and magnitude of angular velocity ω3 of link CD in the four-bar linkage using the relative velocity graphical methodarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





