ELECTRICITY FOR TRADES (LL W/ACCESS)
3rd Edition
ISBN: 9781260699487
Author: Petruzella
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Question
Chapter 4.1, Problem 2RQ
To determine
Define electric current.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Q2- What are the parameters and loss that can be determined during open-circuit test of
singlephase transformer. Draw the circuit diagram of open-circuit test and explain how can you
calculate the Parameters and loss.
Q6- the open circuit and short circuit tests on a 10 KVA, 125/250 v, 50 Hz single phase transformer
gave the following results: O.C. Test: 125 V,0.6 A, 50 W ( on L.V.) S.C. Test: 20 V, 40 A, 177.78 W (on
H.V. side) Calculate: i) Copper losses on half load ii) Full load efficiency at 0.8 leading p.f. iii) Half load
efficiency at 0.8 leading p.f. iv) Regulation at full load at 0.9 leading p.f. Ans: 44.445 W, 97.23%,
97.69%, -1.8015%
Q3-A two-winding transformer has a primary winding with 208 turns and a secondary winding with 6
turns. The primary winding is connected to a 4160V system. What is the secondary voltage at no
load? What is the current in the primary winding with a 50-amp load connected to the secondary
winding? What is the apparent power flowing in the primary and secondary circuits? Ans. 120 V,
1.44 A, 6000 VA
Chapter 4 Solutions
ELECTRICITY FOR TRADES (LL W/ACCESS)
Ch. 4.1 - What is the practical unit of electric charge?Ch. 4.1 - Prob. 2RQCh. 4.1 - Prob. 3RQCh. 4.1 - Explain what a current flow of 1 ampere can be...Ch. 4.1 - Account for the fact that electric current travels...Ch. 4.1 - Prob. 6RQCh. 4.1 - Prob. 7RQCh. 4.1 - Prob. 8RQCh. 4.1 - Prob. 9RQCh. 4.1 - Prob. 10RQ
Ch. 4.1 - Prob. 11RQCh. 4.1 - Prob. 12RQCh. 4.1 - What is the cause and effect of resistance?Ch. 4.1 - When using an ohmmeter to measure resistance, what...Ch. 4.1 - Convert the following data: a. 12,000 A to kA b....Ch. 4.1 - Prob. 16RQCh. 4.2 - Define electric power.Ch. 4.2 - What is the basic unit used to measure electric...Ch. 4.2 - A toaster draws 8 amperes when connected to a...Ch. 4.2 - Prob. 4RQCh. 4.2 - Prob. 5RQCh. 4.2 - Prob. 6RQCh. 4.2 - Prob. 7RQCh. 4.2 - Compare a closed and an open electric circuit.Ch. 4.2 - Prob. 9RQCh. 4.2 - What does Ohms law tell us about current flow in a...Ch. 4.2 - Ohms law is applied to a circuit using what three...Ch. 4.2 - Prob. 12RQCh. 4.2 - Prob. 13RQCh. 4.2 - Prob. 14RQCh. 4.2 - Prob. 15RQCh. 4.2 - Prob. 16RQCh. 4.2 - Prob. 17RQCh. 4.2 - Prob. 18RQ
Knowledge Booster
Similar questions
- Q12- A three phase transformer 3300/400 V,has D/Y connected and working on 50Hz. The line current on the primary side is 12A and secondary has a balanced load at 0.8 lagging p.f. Determine the i) Secondary phase voltage ii) Line current iii) Output power Ans. (230.95 V, 99.11 A, 54.94 kW)arrow_forwardQ1- A single phase transformer consumes 2 A on no load at p.f. 0.208 lagging. The turns ratio is 2/1 (step down). If the loads on the secondary is 25 A at a p.f. 0.866 lagging. Find the primary current and power factor.arrow_forwardQ7- A 5 KVA, 500/250 V,50 Hz, single phase transformer gave the following reading: O.C. Test: 250 V,2 A, 50 W (H.V. side open) S.C. Test: 25 V10 A, 60 W (L.V. side shorted) Determine: i) The efficiency on full load, 0.8 lagging p.f. ii) The voltage regulation on full load, 0.8 leading p.f. iii) Draw the equivalent circuit referred to primary and insert all the values it.arrow_forward
- Q4- A single phase transformer has 350 primary and secondary 1050 turns. The primary is connected to 400 V,50 Hz a.c. supply. If the net cross sectional area of core is 50 cm2, calculate i) The maximum value of the flux density in the core. ii) The induced e.m.f in the secondary winding. Ans: 1.029 T, 1200Varrow_forwardpower systems engineeringarrow_forwardpower systemsarrow_forward
- power system engineeringarrow_forwardTwo PCM encoders, PCMI is used to encode a signal which has maximum frequency of 8 kHz and has 150 voltage levels, while PCM2 is used to encode a signal with maximum frequency of 12.8 kHz and 29 voltage levels. Find the bit rate at the output of each encoder. then apply bit multiplexing and find the bit rate at the output of the multiplexer.arrow_forwardNO AI PLEASEarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning