To determine Calculate the voltage v o for the given circuit of Figure P4.96 in PSPICE by using superposition principle. Explanation Given data: Refer to the given Figure in the textbook, The voltage sources are 240 V and 84 V , the current source is 16 A . Calculation: In the circuit, since there are three sources, let v o = v 1 + v 2 + v 3 Where v 1 , v 2 , and v 3 are contributions due to the 240 V and 84 V voltage sources, and 16 A current source. PSPICE Simulation: When 240 V voltage source is active: Draw the circuit diagram in PSPICE as shown in Figure 1. Save the circuit and provide the Simulation Settings as shown in Figure 2. Now run the simulation and the results will be displayed as shown in Figure 3 by enabling “Enable Bias Voltage Display” icon. When 84 V voltage source is active: Draw the circuit diagram in PSPICE as shown in Figure 4. Save the circuit and provide the Simulation Settings as shown in Figure 5. Now run the simulation and the results will be displayed as shown in Figure 6 by enabling “Enable Bias Voltage Display” icon. When 6 A current source is active: Draw the circuit diagram in PSPICE as shown in Figure 7.

Electrical Circuits and Modified MasteringEngineering - With Access

10th Edition

ISBN: 9780133992793

Author: NILSSON

Publisher: PEARSON

See similar textbooks

Concept explainers

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysi…

Videos

Question

Chapter 4, Problem 96P

To determine

Calculate the voltage vo for the given circuit of Figure P4.96 in PSPICE by using superposition principle.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 4, Problem 95P

Chapter 4, Problem 97P

Students have asked these similar questions

Using D flip-flops, design a synchronous counter. The counter counts in the sequence 1,3,5,7, 1,7,5,3,1,3,5,7,.... when its enable input x is equal to 1; otherwise, the counter count 0. Present state Next state x=0 Next state x=1 Output SO 52 S1 1 S1 54 53 3 52 53 S2 56 51 0 $5 5 54 S4 53 0 55 58 57 7 56 56 55 0 57 S10 59 1 58 58 S7 0 59 S12 S11 7 $10 $10 59 0 $11 $14 $13 5 $12 S12 $11 0 513 $15 SO 3 S14 $14 S13 0 $15 515 SO 0 Explain how to get the table step by step with drawing the state diagram and finding the Karnaugh map.

For the oscillator resonance circuit shown in Fig. (5), derive the oscillation frequency Feedback and open-loop gains. L₁ 5 mH (a) ell +10 V R₁ ww R3 S C2 HH 1 με 1000 pF 100 pF R₂ 1 με RA H (b) +9 V R4 CA 470 pF C₁ R3 HH 1 με R₁ ww L₁ 000 1.5 mH R₂ ww Hi 1 μF L2 m 10 mH

Expert handwritten solution only

Chapter 4 Solutions

Electrical Circuits and Modified MasteringEngineering - With Access

Ch. 4.2 - a) For the circuit shown, use the node-voltage...Ch. 4.2 - Use the node-voltage method to find v in the...Ch. 4.3 - Use the node-voltage method to find the power...Ch. 4.4 - Use the node-voltage method to find vo in the...Ch. 4.4 - Use the node-voltage method to find v in the...Ch. 4.4 - Use the node-voltage method to find v1 in the...Ch. 4.5 - Use the mesh-current method to find (a) the power...Ch. 4.6 - Determine the number of mesh-current equations...Ch. 4.6 - Use the mesh-current method to find vo in the...Ch. 4.7 - Use the mesh-current method to find the power...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.