EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 9780100793439
Author: KALPAKJIAN
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 4, Problem 29QLP
To determine
Explain your understanding of size distortion and shape distortion in heat-treated parts, and describe their causes.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Can someone please help me to answer the following question completely. PLEASE AND THANK YOU!!!
It's important to explain the fundamentals of strain hardening. Is this technique still reliable in hot conditions? Explain
describe the effect that tempering has on material properties
Chapter 4 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 4 - Describe the difference between a solute and a...Ch. 4 - What is a solid solution?Ch. 4 - Prob. 3RQCh. 4 - Describe the difference between a single-phase and...Ch. 4 - What is an induction heater? What kind of part...Ch. 4 - Describe the major features of a phase diagram.Ch. 4 - What do the terms equilibrium and constitutional,...Ch. 4 - Prob. 8RQCh. 4 - What is tempering? Why is it performed?Ch. 4 - Explain what is meant by severity of quenching.
Ch. 4 - What are precipitates? Why are they significant in...Ch. 4 - Prob. 12RQCh. 4 - Prob. 13RQCh. 4 - Prob. 14RQCh. 4 - Prob. 15RQCh. 4 - You may have seen some technical literature on...Ch. 4 - Prob. 17QLPCh. 4 - What is the difference between hardness and...Ch. 4 - Prob. 19QLPCh. 4 - Prob. 20QLPCh. 4 - Prob. 21QLPCh. 4 - Describe the characteristics of (a) an alloy, (b)...Ch. 4 - Explain why carbon, among all elements, is so...Ch. 4 - Prob. 24QLPCh. 4 - In Section 4.8.2, several fluids are listed in...Ch. 4 - Why is it important to know the characteristics of...Ch. 4 - Explain why, in the abscissa of Fig. 4.16c, the...Ch. 4 - Prob. 28QLPCh. 4 - Prob. 29QLPCh. 4 - Prob. 30QLPCh. 4 - Design a heat-treating cycle for carbon steel,...Ch. 4 - Using Fig. 4.4, estimate the following quantities...Ch. 4 - Prob. 33QTPCh. 4 - Prob. 34QTPCh. 4 - Prob. 35SDPCh. 4 - Figure 4.18b shows hardness distributions in...Ch. 4 - Throughout this chapter, you have seen specific...Ch. 4 - Refer to Fig. 4.24, and think of a variety of...Ch. 4 - Inspect various parts in your car or home, and...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Explain how do the cold work processes, such as extrusion or rolling, increase the strength of the single-phase metals? Mention the underlying mechanism in detailsarrow_forwardPlease solvearrow_forwardSingle-crystal technology is applied to nickel alloys that are used as gas turbine blades in aerospace engines. With the aid of sketches describe how a single-crystal casting can be manufactured and explain why a single-crystal casting is likely to have superior creep resistance than a directly-solidified one. Demonstrate the application of the Ten-percent Rule by calculating the approximate tensile strength and elastic modulus in the 0° direction of a carbon-fibre reinforced polymer composite if the strength and elastic modulus in the 0' single ply are 3620 MPa and 143 GPa respectively. The lay-up sequence of the composite is [0,/+45/-45/90-],.arrow_forward
- Ceramics are much stronger in compression rather than indentation explain why?arrow_forwardThe basics of strain hardening should be explained. Is this method still effective at high temperatures? explainarrow_forwardThe same alloy is used to fabricate two different components, both of which result in identical mechanical properties. Cold working yields a microstructure with a much higher incidence of symmetrical grain boundaries for Component 1 as compared with that of Component 2. Which item will most likely have a higher resistance to dynamic embrittlement?arrow_forward
- Determine the % Cold Work of a sample of brass with starting dimensions of Length (L)= 3.0 inches, Width (W)=0.6 inches, and Thickness (T)=0.25 inches, and dimensions after cold work of L=3.5 inches, W= 0.65inches, and T=0.10 inches. Please explain...TIAarrow_forwardWhich one statement is true. Explainarrow_forwardEnumerate and explain each briefly the FOUR (4) Properties of the Bernoulli Process.arrow_forward
- Nickel-based alloys are used for gas turbine blades in aerospace engines. Briefly discuss the characteristics that make these alloys the choice for this application. Single-crystal technology is applied to nickel alloys that are used as gas turbine blades in aerospace engines. With the aid of sketches describe how a single-crystal casting can be manufactured and explain why a single-crystal casting is likely to have superior creep resistance than a directly-solidified one. Demonstrate the application of the Ten-percent Rule by calculating the approximate tensile strength and elastic modulus in the 0° direction of a carbon-fibre reinforced polymer composite if the strength and elastic moduluş in the 0° single ply are 3620 MPa and 143 GPa respectively. The lay-up sequence of the composite is [02/+45/-45/902]s.arrow_forwardCold forming method is applied to many metals and alloys such as steel, aluminum, copper at room temperature and temperatures below it, its strength increases after cold. Explain the factor that causes increased material strength.arrow_forwardA 20 foot long x 4 feet wide x ½ inch thick sheet of an aluminum alloy is cold rolled to a thickness of ¼ inch. During the rolling operation the with of the sheet increases by 10%. The strength coefficient (K) and the strain hardening coefficient (n ) for the aluminum alloy are 25,500 psi and 0.3, respectively. Calculate the length of the sheet after the rolling operation in feet.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
An Introduction to Stress and Strain; Author: The Efficient Engineer;https://www.youtube.com/watch?v=aQf6Q8t1FQE;License: Standard YouTube License, CC-BY