Each compound is to be named. Concept introduction: Molecular compounds contain only nonmetals that are covalently bonded to each other. While naming any molecular compound, the name of the first element is written first, followed by the name of the second element and then, by a suffix “ide” or “ate.” Ionic compounds are named by writing the name of the cation (metal), followed by the name of the anion (nonmetal) and then, by a suffix “ide”. While naming ionic compounds, prefixes, such as di or tri, are not used to indicate the number of atoms. Use the suffix “ide” for monoatomic anion and “ate” for polyatomic anion.

Question

In the Thermo Fisher application note about wine analysis (Lesson 3), the following chromatogram was collected of nine components of wine. If peak 3 has a retention time of 3.15 minutes and a peak width of 0.070 minutes, and peak 4 has a retention time of 3.24 minutes and a peak width of 0.075 minutes, what is the resolution factor between the two peaks? [Hint: it will help to review Lesson 2 for this question.] MAU 300 200 T 34 5 100- 1 2 CO 6 7 8 9 0 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 Minutes 3.22 0.62 1.04 O 1.24

Answer 1

Question

Chapter 4, Problem 23E

Interpretation Introduction

Interpretation:

Each compound is to be named.

Concept introduction:

Molecular compounds contain only nonmetals that are covalently bonded to each other.

While naming any molecular compound, the name of the first element is written first, followed by the name of the second element and then, by a suffix “ide” or “ate.”

Ionic compounds are named by writing the name of the cation (metal), followed by the name of the anion (nonmetal) and then, by a suffix “ide”.

While naming ionic compounds, prefixes, such as di or tri, are not used to indicate the number of atoms.

Use the suffix “ide” for monoatomic anion and “ate” for polyatomic anion.

Expert Solution & Answer

Trending nowThis is a popular solution!

See solution

Check out sample textbook solution

Students have asked these similar questions

In the Thermo Fisher application note about wine analysis (Lesson 3), the following chromatogram was collected of nine components of wine. If peak 3 has a retention time of 3.15 minutes and a peak width of 0.070 minutes, and peak 4 has a retention time of 3.24 minutes and a peak width of 0.075 minutes, what is the resolution factor between the two peaks? [Hint: it will help to review Lesson 2 for this question.] MAU 300 200 T 34 5 100- 1 2 CO 6 7 8 9 0 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 Minutes 3.22 0.62 1.04 O 1.24

The diagram shows two metals, A and B, which melt at 1000°C and 1400°C. State the weight percentage of the primary constituent (grains of C) that would be obtained by solidifying a 20% alloy of B. 1000°C a+L L+C 900°С 12 α a+C 45 1200 C L+y 140096 C+Y a+ß 800°C 700°C C+B 96 92 a+B 0 10 20 30 40 50 60 70 80 90 100 A % peso B B

8. Choose the compound that will produce the spectrum below and assign the signals to the corresponding protons. 2 4 3 ō (ppm) OH 4 6 6 СОН 2 1 0