![EBK THINKING LIKE AN ENGINEER](https://www.bartleby.com/isbn_cover_images/8220103633512/8220103633512_largeCoverImage.jpg)
EBK THINKING LIKE AN ENGINEER
4th Edition
ISBN: 8220103633512
Author: OHLAND
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 4, Problem 1RQ
- 1. When thinking about how you will phrase things for a talk, you should
- A. Mirror your exact wording in your slides.
- B. Be sure to use words that demonstrate your mastery of the topic.
- C. Find a way to capture the attention of the audience.
- D. Split your topic into as many points as you can.
Expert Solution & Answer
![Check Mark](/static/check-mark.png)
To determine
Choose the correct option.
Answer to Problem 1RQ
The correct option is C. One should find a way to capture the attention of the audience.
Explanation of Solution
In any speech, know your audience is the foremost step of the preparation. The ultimate purpose of the talk is to keep the audience interested. They will continue to pay an attention only if the speech is interesting and relevant to them. Therefore, the speaker should find an exact way to capture the attention of the audience when thinking about to phrase the things for a talk.
Therefore from the given option (C) is correct and options (A), (B), and (D) are incorrect.
Conclusion:
Hence, the correct option is C. One should find a way to capture the attention of the audience.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Draw top, side, front view With pen(cil) and paper
Multi view drawing and handwriting all of it
A wheel of diameter 150.0 mm and width 37.00 mm carrying a load 2.200 kN rolls on a
flat rail. Take the wheel material as steel and the rail material as cast iron. Assume the
figure given, which is based on a Poisson's ratio of 0.3, is applicable to estimate
the depth at which the maximum shear stress occurs for these materials. At this critical
depth, calculate the Hertzian stresses σr, σy, σz, and Tmax for the wheel.
1.0
0.8
0, т
Ratio of stress to Pmax
0.4
0.6
90
69
0.2
0.5b
b
1.5b
Tmax
2b
Distance from contact surface
The Hertizian stresses are as follows:
02 = or = -23.8 psi for the wheel =|
necessary.)
σy for the wheel =|
MPa
σz for the wheel =
MPa
V4 for the wheel = |
MPa
2.5b
ཡི
3b
MPa (Include a minus sign if
Only question 3
Chapter 4 Solutions
EBK THINKING LIKE AN ENGINEER
Ch. 4 - 1. When thinking about how you will phrase things...Ch. 4 - 2. Which statement is NOT good advice for...Ch. 4 - Prob. 3RQCh. 4 - 4. Which of the following sentences is the best...Ch. 4 - In researching a topic, which method is NOT a good...Ch. 4 - 6. When writing a memo or short report, where...Ch. 4 - 7. When writing a memo or short report, where...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In cold isostatic pressing, the mold is most typically made of which one of the following: thermosetting polymer tool steel sheet metal textile rubberarrow_forwardThe coefficient of friction between the part and the tool in cold working tends to be: lower higher no different relative to its value in hot workingarrow_forwardThe force F={25i−45j+15k}F={25i−45j+15k} lblb acts at the end A of the pipe assembly shown in (Figure 1). Determine the magnitude of the component F1 which acts along the member AB. Determine the magnitude of the component F2 which acts perpendicular to the AB.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9781133612315/9781133612315_smallCoverImage.gif)
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Quality Control and Quality Assurance; Author: AISC Education;https://www.youtube.com/watch?v=C2PFj9YZ_mw;License: Standard Youtube License