Integrated Science
Integrated Science
7th Edition
ISBN: 9780077862602
Author: Tillery, Bill W.
Publisher: Mcgraw-hill,
bartleby

Concept explainers

bartleby

Videos

Question
Book Icon
Chapter 4, Problem 11PEA
To determine

The amount of heat absorbed when 100.0g of water at 20.0°C is heated to steam at 125.0°C.

Expert Solution & Answer
Check Mark

Answer to Problem 11PEA

The amount of heat absorbed when 100.0g of water at 20.0°C is heated to steam at 125.0°C is 63.20kcal.

Explanation of Solution

To change the water at 20.0°C into steam at 125.0°C, three different quantities of heat are required.

First is the heat required to raise the temperature of water to 100.0°C. Second is the heat required to cause a phase change from water to steam at 100.0°C. Third is the heat required to raise the temperature of steam to 125.0°C.

Write the expression for the total heat absorbed.

    Q=Q1+Q2+Q3                                                               (I)

Here, Q is the total heat energy absorbed, Q1 is the heat required to raise the temperature of water, Q2 is the heat required for phase change of water and Q3 is the heat required to raise the temperature of steam.

Write the expression for the heat required to raise the temperature of water.

    Q1=mcwaterΔTwater                                                           (II)

Here, m is the mass of the water, cwater is the specific heat of water and ΔTwater is the change in temperature of water.

Water completely changes to steam. Hence, the mass of water is same as the mass of steam.

Write the expression for the heat required for phase change of water.

    Q2=mLv                                                                      (III)

Here, Q2 is the heat required for phase change of water, m is the mass of water and Lv is the latent heat of vaporization for water.

Write the expression for the heat required to raise the temperature of steam.

    Q3=mcsteamΔTsteam                                                        (IV)

Here, m is the mass of the steam, csteam is the specific heat of steam and ΔTsteam is the change in temperature of steam.

Write the expression for the change in temperature.

    ΔT=T2T1                                                                  (V)

Here, T2 is the final temperature and T1 is the initial temperature.

Conclusion:

Substitute 20.0°C for T1 and 100.0°C for T2 in equation (V) to find ΔTwater.

    ΔTwater=100.0°C20.0°C=80.0°C

Substitute 80.0°C for ΔTwater, 100.0g for m and 1.00cal/g°C for cwater in equation (II) to find Q1.

    Q1=(100.0g)(1.00cal/g°C)(80.0°C)=8000cal

Substitute 100.0g for m and 540.0cal/g for Lv in equation (III) to find Q2.

    Q2=(100.0g)(540.0cal/g)=54000cal

Substitute 100.0°C for T1 and 125.0°C for T2 in equation (V) to find ΔTsteam.

    ΔTsteam=125.0°C100.0°C=25.0°C

Substitute 25.0°C for ΔTsteam, 100.0g for m and 0.480cal/g°C for csteam in equation (IV) to find Q3.

    Q3=(100.0g)(0.480cal/g°C)(25.0°C)=1200cal

Substitute 8000cal for Q1, 54000cal for Q2 and 1200cal for Q3 in equation (I) to find Q.

    Q=8000cal+54000cal+1200cal=(63200cal×103kcal1cal)=63.20kcal

Therefore, the amount of heat absorbed when 100.0g of water at 20.0°C is heated to steam at 125.0°C is 63.20kcal.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
How can you tell which vowel is being produced here ( “ee,” “ah,” or “oo”)? Also, how would you be able to tell for the other vowels?
You want to fabricate a soft microfluidic chip like the one below. How would you go about fabricating this chip knowing that you are targeting a channel with a square cross-sectional profile of 200 μm by 200 μm. What materials and steps would you use and why? Disregard the process to form the inlet and outlet. Square Cross Section
1. What are the key steps involved in the fabrication of a semiconductor device. 2. You are hired by a chip manufacturing company, and you are asked to prepare a silicon wafer with the pattern below. Describe the process you would use. High Aspect Ratio Trenches Undoped Si Wafer P-doped Si 3. You would like to deposit material within a high aspect ratio trench. What approach would you use and why? 4. A person is setting up a small clean room space to carry out an outreach activity to educate high school students about patterning using photolithography. They obtained a positive photoresist, a used spin coater, a high energy light lamp for exposure and ordered a plastic transparency mask with a pattern on it to reduce cost. Upon trying this set up multiple times they find that the full resist gets developed, and they are unable to transfer the pattern onto the resist. Help them troubleshoot and find out why pattern of transfer has not been successful. 5. You are given a composite…
Knowledge Booster
Background pattern image
Physics
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Text book image
College Physics
Physics
ISBN:9781285737027
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
Text book image
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Text book image
College Physics
Physics
ISBN:9781305952300
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
Text book image
An Introduction to Physical Science
Physics
ISBN:9781305079137
Author:James Shipman, Jerry D. Wilson, Charles A. Higgins, Omar Torres
Publisher:Cengage Learning
Text book image
Physics for Scientists and Engineers, Technology ...
Physics
ISBN:9781305116399
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Heat Transfer: Crash Course Engineering #14; Author: CrashCourse;https://www.youtube.com/watch?v=YK7G6l_K6sA;License: Standard YouTube License, CC-BY