Explanation Given data: Refer to Figure given in the textbook. The current source is I g 1 = 12 A and I g 2 = 16 A . The resistors R 1 = 25 Ω , R 2 = 5 Ω , R 3 = 50 Ω , and R 4 = 75 Ω . Calculation: Refer to the equation given in the textbook, the sensitivity of the node voltage v 1 for the given circuit is as follows, v 1 = R 1 { R 3 R 4 I g 2 − [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] I g 1 } ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (1) The sensitivity of v 1 with respect to I g 1 is calculated by differentiating equation (1) with respect to I g 1 as follows, d v 1 d I g 1 = R 1 { R 3 R 4 ( 0 ) − [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] ( 1 ) } ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 { ∵ I g 2 = 0 , I g 1 = 1 } = R 1 { 0 − [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] } ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 d v 1 d I g 1 = − R 1 [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (2) The sensitivity of v 1 with respect to I g 2 is calculated by differentiating equation (1) with respect to I g 2 as follows, d v 1 d I g 2 = R 1 { R 3 R 4 ( 1 ) − [ R 2 ( R 3 + R 4 ) + R 3 R 4 ] ( 0 ) } ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 { ∵ I g 1 = 0 , I g 2 = 1 } = R 1 [ R 3 R 4 − 0 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 d v 1 d I g 2 = R 1 R 3 R 4 ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (3) Refer to the equation given in the textbook, the sensitivity of the node voltage v 2 for the given circuit is as follows, v 2 = R 3 R 4 [ ( R 1 + R 2 ) I g 2 − R 1 I g 1 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (4) The sensitivity of v 2 with respect to I g 1 is calculated by differentiating equation (4) with respect to I g 1 as follows, d v 2 d I g 1 = R 3 R 4 [ ( R 1 + R 2 ) ( 0 ) − R 1 ( 1 ) ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 { ∵ I g 2 = 0 , I g 1 = 1 } = R 3 R 4 [ 0 − R 1 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 d v 2 d I g 1 = − R 1 R 3 R 4 ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (5) The sensitivity of v 2 with respect to I g 2 is calculated by differentiating equation (4) with respect to I g 2 as follows, d v 2 d I g 2 = R 3 R 4 [ ( R 1 + R 2 ) ( 1 ) − R 1 ( 0 ) ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 { ∵ I g 1 = 0 , I g 2 = 1 } = R 3 R 4 [ ( R 1 + R 2 ) − 0 ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 d v 2 d I g 2 = R 3 R 4 [ ( R 1 + R 2 ) ] ( R 1 + R 2 ) ( R 3 + R 4 ) + R 3 R 4 (6) Substitute 25 for R 1 , 5 for R 2 , 50 for R 3 , and 75 for R 4 in equation (2) to find the sensitivity of v 1 with respect to I g 1

11th Edition

ISBN: 9780134746968

Author: James W. Nilsson, Susan Riedel

Publisher: PEARSON

See similar textbooks

Concept explainers

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Mori…

Videos

Question

Chapter 4, Problem 107P

To determine

Find the values of node voltage v1 and v2 if Ig1 is decreased to 11 A and Ig2 is increased to 17 A of the given circuit using PSPICE.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 4, Problem 106P

Chapter 4, Problem 108P

Students have asked these similar questions

A robot gripper is shown on Fig.1a. The block diagram of the control system is shown in Fig.1b. This system is conditionally stable because it is stable only for a range of the gain K. Using the Routh-Hurwitz criterion method to determine the range of gain for which the system is stable. Find the steady-state error due to unit step input. Sketch the root locus of the system and analyze its stability. Find the value of K so that the phase margin is minimum, and record the values of the phase margin, gain margin, Mr, and BW. Then draw the Bode plot of the system and discuss its stability using the Nyquist stability method. What is the value of this maximum overshoot for both large and small values of K due to unit step input? Draw the response of the open-loop and closed-loop of the system according to the unit step system for k=15, 25, 50. Discuss how to improve the system response if needed.

Please show the steps

Don't use ai to answer I will report you answer

Chapter 4 Solutions

Electric Circuits. (11th Edition)

Ch. 4.2 - a) For the circuit shown, use the node-voltage...Ch. 4.2 - Use the node-voltage method to find v in the...Ch. 4.3 - Use the node-voltage method to find the power...Ch. 4.4 - Use the node-voltage method to find vo in the...Ch. 4.4 - Use the node-voltage method to find v in the...Ch. 4.4 - Use the node-voltage method to find v1 in the...Ch. 4.5 - Use the mesh-current method to find (a) the power...Ch. 4.6 - Determine the number of mesh-current equations...Ch. 4.6 - Use the mesh-current method to find vo in the...Ch. 4.7 - Use the mesh-current method to find the power...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Find the values of node voltage v 1 and v 2 if I g 1 is decreased to 11 A and I g 2 is increased to 17 A of the given circuit using PSPICE.

Concept explainers

Videos

Find the values of node voltage v1 and v2 if Ig1 is decreased to 11 A and Ig2 is increased to 17 A of the given circuit using PSPICE.

Want to see the full answer?

Chapter 4 Solutions