Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 39, Problem 3MC
Worn teeth on a speed gear can cause_______.
a. gear clash
b. hard shifting
c. the transmission to shift into a gear
d. the gear to jump out
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
When an idler gear is placed between the driving and driven gears, the driven gear:a. rotates the opposite direction as the drive gearb. rotates the same direction as the drive gearc. reduces the torque transfer from the drivegear to the driven geard. none of the above
Using a lubricant that is thicker than the specifiedlubricant can lead to __ .a. the gear to jump outb. hard shiftingc. gear lockupd. gear slippage
How to draw an involute spur gear.
Chapter 39 Solutions
Automotive Technology
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2SACh. 39 - Prob. 3SACh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - What should you do to properly identify the type...Ch. 39 - List at least five items that are typically...Ch. 39 - Prob. 1TFCh. 39 - True or False? Bearing noise increases under load...
Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - Technician A says that shims may be used to adjust...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following gear ratios indicates an over-drive condition? a. 2.15:1 b. 1:1 c. 0.85:1 d. None of the abovearrow_forwardIn a simple planetary gearset, when the planetary carrier is held, the gearset produces a______. a. reverse b. direct drive c. fast overdrive d. forward reductionarrow_forwardTechnician A says that when a car is moving straight ahead, all differential gears rotate as a unit. Technician B says that when a car is turning a corner, the inside differential side gear rotates slowly on the pinion, causing the outside side gear to rotate faster. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Using a lubricant that is thicker than the specified lubricant can lead to_____. a. the gear to jump out b. hard shifting c. gear lockup d. gear slippagearrow_forwardDefine the purpose of the final drive gears.arrow_forwardTechnician A says that a gear tooth pattern identifies ring gear runout. Technician B says that gear patterns are not accurate if there is excessive ring gear runout. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- what occurs in a differential during cornering? a. the inside axle side gear turns faster than the outer axle side gear b the case turns at the same speed as the drive shaft c the crown gear will slow down slightly d the pinion/spider gears rotate on the pinion shaftarrow_forwardIn a transaxle, the pinion gear on the pinionshaft meshes with the ___.a. reverse idler gearb. ring gearc. countershaft drive geard. input geararrow_forwardWhat TWO main characteristics do idler gears offer when used in a gear system?arrow_forward
- QUESTION 1: THE GEAR DRIVE Figure 1 Example of a simple spur gear train with an idler A simple spur gear train with an idler must transmit 650 W power. The pinion A is rotating at 92 rpm in an anticlockwise direction. Gear C has 45 teeth. Both the pinion and the idler are of the same size. Material proposed for pinion A and gear C is heavy- duty 817M40 steel, while for idler B is heavy-duty 655M13 Case hardened steel.arrow_forwardThe component used to ensure that the mainshaft (output shaft) and main (speed) gear locked to it are rotating at the same speed is known as a_____. a. synchronizer b. shift detent c. shift fork d. transfer casearrow_forwardA clicking noise during transrnission/transaxle operation may be an indication of ________. a. worn mainshaft (input shaft) bearings b. faulty synchronizer operation c. failed oil seals d. worn, broken, or chipped gear teetharrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License