Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 39, Problem 4MC
Using a lubricant that is thicker than the specified lubricant can lead to_____.
a. the gear to jump out
b. hard shifting
c. gear lockup
d. gear slippage
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
what occurs in a differential during cornering?
a. the inside axle side gear turns faster than the outer axle side gear
b the case turns at the same speed as the drive shaft
c the crown gear will slow down slightly
d the pinion/spider gears rotate on the pinion shaft
When an idler gear is placed between the driving and driven gears, the driven gear:a. rotates the opposite direction as the drive gearb. rotates the same direction as the drive gearc. reduces the torque transfer from the drivegear to the driven geard. none of the above
Please do it quickly
Chapter 39 Solutions
Automotive Technology
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2SACh. 39 - Prob. 3SACh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - What should you do to properly identify the type...Ch. 39 - List at least five items that are typically...Ch. 39 - Prob. 1TFCh. 39 - True or False? Bearing noise increases under load...
Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - Technician A says that shims may be used to adjust...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that a gear tooth pattern identifies ring gear runout. Technician B says that gear patterns are not accurate if there is excessive ring gear runout. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhen servicing transfer cases, all of the following are correct, except_____. a. it must be supported on a transmission jack or safety stands b. the chain drive and a planetary gearset must be adjusted to specifications c. visual inspections for leaks and damage are necessary d. follow the manufacturers recommendations for lubricantsarrow_forwardTech A says that if a noise is caused by a set of worn gears, it will normally be loudest in that gear while driving under a load. Tech B says that if the bearings on the input shaft, countershaft, or main shaft are worn, either front or rear, a growling noise will result when stopped in gear. Who is correct?arrow_forward
- In a transaxle, the pinion gear on the pinionshaft meshes with the ___.a. reverse idler gearb. ring gearc. countershaft drive geard. input geararrow_forwardWords: Accelerating, Float, Gear, Noise, Tooth, VehicleCrown wheel and pinion noise originates from poor ________________ contact and may be noticed on drive, overdrive or________________. It can be more pronounced on one of these than on the others.Drive noise is most pronounced when ________________, as the gear teeth are under load. The bearings are also under loadso that any lack of preload will allow the ________________ teeth to change their area of contact.Noise on overdrive occurs as the ________________ decelerates from medium speeds, while float ________________occurs under light cruising conditions.arrow_forwardA clicking noise during transrnission/transaxle operation may be an indication of ________. a. worn mainshaft (input shaft) bearings b. faulty synchronizer operation c. failed oil seals d. worn, broken, or chipped gear teetharrow_forward
- A clicking noise during transmission/transaxle operationmay be an indication of __ .a. worn mainshaft (input shaft) bearingsb. faulty synchronizer operationc. failed oil sealsd. worn, broken, or chipped gear teetharrow_forwardType the name of the part in the blank provided below. We have flywheel present in manual gear cars but We have ___________in automatic gear cars.arrow_forwardWhat can too much clutch pedal free play cause? a.hard gear shifting b.fast release bearing wear c.release fork wear d.clutch slippingarrow_forward
- While discussing a pressure test: Technician A says that this test is the most valuable diagnostic check for slippage when a gear is engaged. Technician B says that the test can identify the cause of late or harsh shifting. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardIn a simple planetary gearset, when the planetary carrier is held, the gearset produces a______. a. reverse b. direct drive c. fast overdrive d. forward reductionarrow_forwardPlease answer 1, 2 and 3arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Principles of Lubrication | Automobile Engineering; Author: Magic Marks;https://www.youtube.com/watch?v=MGbbSxZTdCQ;License: Standard Youtube License