AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
7th Edition
ISBN: 9780357096789
Author: ERJAVEC
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 37, Problem 2ASRQ
While discussing ways to determine if a pilot bushing is faulty: Technician A says that if it operated quietly, it does not need to be replaced. Technician B says that a careful inspection of the transmission’s input shaft can determine the condition of the pilot bushing. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says that some small cracks in
the accessory drive belt may be within
tolerance. Technician B says that serpentine
belts can be checked with a wear gauge.
Who is correct?
Select one:
a. Technician A only
b. Technician B only
C. Both A and B
d. Neither A nor B
When discussing shift problems,
Technician A says that worn or broken engine and
transaxle mounts can cause a transaxle to have
shifting problems.
Technician B that poor shift boot alignment
can cause a transaxle to jump out of gear.
says
Who is correct?
A. A only
C. Both A and B
B. B only
D. Neither A nor B
A discussion concerning CV joint testing is being held.
Technician A says that a recommended method to check CV joints is to raise the vehícle so that the lower control arms are hanging freely; at this point the engine can be
accelerated while noise checks can be performed.
Technician B says that the vehicle should be road tested so that the CV joints can be checked under load.
Who is correct?
O a. A only
O b. B only
c. Both A and B
d. Neither A nor B
Chapter 37 Solutions
AUTOMOTIVE TECHNOLOGY -W/MINDTAP ACCESS
Ch. 37 - What is another name for the diaphragm spring?Ch. 37 - What is used to measure clutch pedal play?Ch. 37 - The pressure plate moves away from the flywheel...Ch. 37 - Name three types of clutch linkages.Ch. 37 - True or False? If the fluid reservoir for a...Ch. 37 - True or False? Both the clutch and the brake...Ch. 37 - The clutch, or friction, disc is connected to the....Ch. 37 - Torsional coil springs in the clutch disc_____. a....Ch. 37 - Which of the following is probably not the cause...Ch. 37 - When the clutch pedal is released on a hydraulic...
Ch. 37 - When the clutch is disengaged, the power flow...Ch. 37 - Insufficient clutch pedal clearance results...Ch. 37 - Before making a clutch adjustment, it is necessary...Ch. 37 - The surface of the pressure plate contacts the. a....Ch. 37 - Which of the following would not cause clutch...Ch. 37 - Technician A says that clutch slippage is most...Ch. 37 - While discussing ways to determine if a pilot...Ch. 37 - While discussing the different types of pressure...Ch. 37 - While discussing the purpose of a clutch pressure...Ch. 37 - Technician A says that an oil-soaked clutch disc...Ch. 37 - While discussing different abnormal clutch noises:...Ch. 37 - Technician A says that incorrect clutch adjustment...Ch. 37 - While discussing the cause of a pulsating clutch...Ch. 37 - Technician A says that if the hydraulic clutch...Ch. 37 - Technician A says that all manual transmission...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is still apparent but is less pronounced. Technician A says that the left inner CV joint may be the source of the noise. Technician B says that the left outer CV joint may be causing the noise. Who is correct? O a. A only Ob.B only O c. Both A and B O d. Neither A nor Barrow_forwardFrom the following identify a true statement regarding the adjustment of drive belt tension. a. Less than 8 mm should be the correct a deflection for each belt which is under tension b. More than 6 mm should be the correct a deflection for each belt which is under tension c. More than 8 mm should be the correct a deflection for each belt which is under tension. d. More than 6 mm and less than 8 mm should be the correct a deflection for each belt which is under tension.arrow_forwardWhen reviewing the procedure for replacing an axle boot, Technician A says that the position of the old boot should be marked on the shaft before removing it. Technician B says that if the boot is dimpled or collapsed after the new boot is installed, a dulled screwdriver should be used to allow air to enter the boot. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forward
- All of the following are functions of the flywheel, except it ____ . a. provides a mounting place for the clutch assembly b. smooths out cylinder firing pulsations c. has marks used to set the valve timing d. meshes with the starter drive geararrow_forwardThe CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the right side of the vehicle appear to be stretched apart. Technician A says that one or more of the engine/transaxle's mounts may be broken. Technician B says that one or more of the engine/transaxle's subframe mounts may be broken. Who is correct? O a. A only O b.B only C. Both A and B O d. Neither A nor Barrow_forwardWhich of the following components is replaced as an assembly?a. The transfer caseb. the viscous clutchc. The interaxle differentiald. all wheel drive transaxlesarrow_forward
- Technician A says that broken or worn engine and transaxle mounts can cause a transaxie to have shiftinf problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear.Who is correct? a.Technician A only b.Technician B only c. both A and B d. Neither A or nor B.arrow_forwardWhen installing a new release bearing, Technician A says the outer surface of thetransmission's front bearing retainer should be lubricated. Technician B says the release lever and pivot shuold be lubricated who is correct? a. techincian A b. Technician B c. both A and B d. Neither A or Barrow_forwardTechnician A says that shift solenoids direct fluid flow to and away from the apply devices in the transmission. Technician B says that shift solenoids are used to mechanically apply a friction brake or multiple-disc clutch assembly. Who is correct?arrow_forward
- Pinion gear-to-flywheel ring gear clearance is beingdiscussed: Technician A says that if there is too muchclearance, there will be a high pitch while the enginecranks. Technician B says that if there is too littleclearance, there will be a high pitch noise after theengine is started. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forwardA car jumps out of gear into neutral, particularlywhen decelerating or going down hills: Technician Achecks the shift lever and external gearshift linkagefirst. Technician B says that the clutch pilot bearingcould be the problem. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor Barrow_forwardTechnician A says a sticking inboard joint can cause the car to shimmy during acceleration. Technician B says a worn inboard joint can cause a clunking during acceleration and deceleration. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
General Industrial Safety; Author: Jim Pytel;https://www.youtube.com/watch?v=RXtF_vQRebM;License: Standard youtube license