Degarmo's Materials And Processes In Manufacturing

13th Edition

ISBN: 9781119492825

Author: Black, J. Temple, Kohser, Ronald A., Author.

Publisher: Wiley,

See similar textbooks

Videos

Textbook Question

Chapter 35, Problem 2P

Two pieces of AISI 1025 steel are being shielded-metal-arc welded with E6012 electrodes. Some difficulty is being experienced with cracking in the weld beads and in the heat-affected zones. What possible corrective measures might you suggest?

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 35, Problem 1P

Chapter 35, Problem 3P

Students have asked these similar questions

A bracket to be welded into a steel channel using E-60 electrode 345 Mpa) Two welding sets are suggested as shown in Fig. (1)Based on maximum shear stress failure theory and safety factor of (2.5) (a) Find the weld size for each set. (b) Which set would you recommend A or B ?

An axially-loaded welded angular connection is shown SD-002 . The angular section 150 x 100 x 10 mm having an area of 2400 mm? is welded to a gusset plate having a thickness of 10 mm. All steel is A 36 (Fy = 248 MPa, Fu = 400 MPa) and E (70) electrodes (Fu = 484 MPa) is used. Using the shielded metal-arc welding process. Compute the value of "a" if T = 500 kN. (Please do not round-off to whole number the required thickness, use the exact (2 decimal) value.) 150 mm SD-002

Assume that two 1.5-mm thick steel sheets are being spot welded at a current of 4000 A and current-flow time is 0.3 s. Using electrodes 5 mm in diameter, estimate the amount of heat generated and the amount of heat required to melt the weld nugget. Use an effective resistance of 350 un. Take u= 9,7 Joule/mm Which one of the following are correct? O a. If the electrodes were 7 mm diameter, the amount of heat generated would decrease b. The amount of heat generated by the equipment is between 1600 to 1700 Joules c. The equipment has enough power to weld the steel sheets. d. The equipment does not have enough power to weld the steel sheets e. The amount of heat required is between 700 and 750 Joules

Chapter 35 Solutions

Degarmo's Materials And Processes In Manufacturing

Ch. 35 - What types of design features favor manufacture as...Ch. 35 - What types of manufacturing processes fall under...Ch. 35 - Define welding.Ch. 35 - What conditions are required to produce an ideal...Ch. 35 - What are some of the ways in which welding...Ch. 35 - What are some possible problems associated with...Ch. 35 - What are the three primary aspects required to...Ch. 35 - How are welding processes identified by the...Ch. 35 - What is thermal cutting?Ch. 35 - What are some of the common types of weld defects?

Additional Engineering Textbook Solutions

Find more solutions based on key concepts

1.1 What is the difference between an atom and a molecule? A molecule and a crystal?

Manufacturing Engineering & Technology

along the v axis. Prob. F2-6

Engineering Mechanics: Statics

Figure 8.12shows a portion of a fire protection system in which a pump draws water at 60 F from a reservoir and...

Applied Fluid Mechanics (7th Edition)

The R4l0A in Problem 3.1 2c is at 1000kPa,50C with a mass of 0.1kg . It is cooled so that the volume is reduced...

Fundamentals Of Thermodynamics

A cooling coil consists of a bank of aluminum (k=237W/mK) finned tubes having the core configuration of Figure ...

Fundamentals of Heat and Mass Transfer

What parts are included in the vehicle chassis?

Automotive Technology: Principles, Diagnosis, and Service (5th Edition)

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.