To draw out inferences for the given questions on the basis of the table that shows the water potential measurements in a 100-meter tall tree and its surroundings, with the gravity force of –0.01 MPa (megapascal) per meter of height above the ground and states the reasons for: (a) Sufficient leaf water potential in order to draw the water to the top of the tree, (b) Continuation of transpiration if the soil potential is decreased to –1.0 MPa, and (c) Effect on water potential of xylem if all the stomata are closed. Introduction: Water potential refers to the relative measurement of the tendency of water to flow along a concentration gradient, that is, from the region of high potential to the lower potential regions. It is caused by osmosis, surface tension, and any physical pressure. It is measured in MPa (megapascals) and represented by the Greek letter “psi” ( Ψ ). The following table represents the region of the plant and the water potential values in these regions: Region Water potential (MPa) Soil water –0.3 Xylem of root –0.6 Xylem of trunk –1.2 Inside of leaf –2.0 Outside air –58.5

Question

Want to see the full answer?

Answer 1

Question

Chapter 34.2, Problem 2R

Summary Introduction

To review:

To draw out inferences for the given questions on the basis of the table that shows the water potential measurements in a 100-meter tall tree and its surroundings, with the gravity force of –0.01 MPa (megapascal) per meter of height above the ground and states the reasons for:

(a) Sufficient leaf water potential in order to draw the water to the top of the tree,

(b) Continuation of transpiration if the soil potential is decreased to –1.0 MPa, and

(c) Effect on water potential of xylem if all the stomata are closed.

Introduction:

Water potential refers to the relative measurement of the tendency of water to flow along a concentration gradient, that is, from the region of high potential to the lower potential regions. It is caused by osmosis, surface tension, and any physical pressure. It is measured in MPa (megapascals) and represented by the Greek letter “psi” (Ψ).

The following table represents the region of the plant and the water potential values in these regions:

Region Water potential (MPa)

Soil water –0.3

Xylem of root –0.6

Xylem of trunk –1.2

Inside of leaf –2.0

Outside air –58.5

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

A sample of blood was taken from the above individual and prepared for haemoglobin analysis. However, when water was added the cells did not lyse and looked normal in size and shape. The technician suspected that they had may have made an error in the protocol – what is the most likely explanation? The cell membranes are more resistant than normal. An isotonic solution had been added instead of water. A solution of 0.1 M NaCl had been added instead of water. Not enough water had been added to the red blood cell pellet. The man had sickle-cell anaemia.

With reference to their absorption spectra of the oxy haemoglobin intact line) and deoxyhemoglobin (broken line) shown in Figure 2 below, how would you best explain the reason why there are differences in the major peaks of the spectra? Figure 2. SPECTRA OF OXYGENATED AND DEOXYGENATED HAEMOGLOBIN OBTAINED WITH THE RECORDING SPECTROPHOTOMETER 1.4 Abs < 0.8 06 0.4 400 420 440 460 480 500 520 540 560 580 600 nm 1. The difference in the spectra is due to a pH change in the deoxy-haemoglobin due to uptake of CO2- 2. There is more oxygen-carrying plasma in the oxy-haemoglobin sample. 3. The change in Mr due to oxygen binding causes the oxy haemoglobin to have a higher absorbance peak. 4. Oxy-haemoglobin is contaminated by carbaminohemoglobin, and therefore has a higher absorbance peak 5. Oxy-haemoglobin absorbs more light of blue wavelengths and less of red wavelengths than deoxy-haemoglobin