Refrigeration and Air Conditioning Technology (MindTap Course List)
8th Edition
ISBN: 9781305578296
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 33, Problem 7RQ
The "point of no pressure change" is located at the
A. outlet of the circulator pump.
B. inlet of the expansion tank.
C. inlet of the pressure-reducing valve.
D. outlet of the pressure relief valve.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The process of filling the liquid into the suction pipe and pump casing upto the level of delivery valve is called as _________.
a.
leveling
b.
pumping
c.
priming
d.
filling
What part of the circulating system has the maximum pressure drop across it?
a. Drill pipe
b. Surface line
c. Drill collar
d. Bit nozzles
For a hydraulic power unit, this part protects the pump from taking in any harmful particles that may be in the reservoir
a. liquid level gauge
b. filler/breather
c. pressure gauge
d. suction strainer
Chapter 33 Solutions
Refrigeration and Air Conditioning Technology (MindTap Course List)
Ch. 33 - A hydronic heating system uses ______to move heat...Ch. 33 - Describe a zone in a hydronic heating system.Ch. 33 - Name four sources of heat commonly used for...Ch. 33 - Give three reasons that air is detrimental to a...Ch. 33 - Explain the difference between a wet-base and a...Ch. 33 - Where is air vented from a hydronic heating...Ch. 33 - The "point of no pressure change" is located at...Ch. 33 - The purpose of a limit control in a boiler is to...Ch. 33 - The device that relieves the pressure in a boiler...Ch. 33 - Describe the function of a low-water cutoff.
Ch. 33 - The relief valve setting for a typical...Ch. 33 - Describe how an air cushion tank functions in a...Ch. 33 - True or False: City water does not contain air.Ch. 33 - State two ways that air can get into a hydronic...Ch. 33 - The most common type of pump used for hydronic...Ch. 33 - Another term for pump pressure is feet of _______.Ch. 33 - Two types of zone control valves are the _____and...Ch. 33 - Why must expansion be considered when sizing...Ch. 33 - How is expansion in hot water pipes handled?Ch. 33 - Sketch the following systems: one pipe, two-pipe...Ch. 33 - Describe the advantage of a two-pipe...Ch. 33 - The pressure differential bypass valve is most...Ch. 33 - What is the heat output, in Btu/h, of a terminal...Ch. 33 - In a primary-secondary pumping arrangement, the...Ch. 33 - The temperature of the water at the outlet of a...Ch. 33 - A tankless water-heating system gets its heat from...Ch. 33 - How much of the sun's energy actually reaches the...Ch. 33 - The varying intensity of the sun's energy that...Ch. 33 - Drain-down systems would best be used in which...Ch. 33 - Why are solar systems intended to be used as a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The name of the fitting where the branch line connects to the main duct is the ________.arrow_forwardWhat is the advantage of using an injector-type mixing chamber?arrow_forwardSpeed of the actuator is affected by a. pipe diameter b. all of the mentioned c. cross-section area of the orifice d. velocity of flowarrow_forward
- When there is an excess potential energy during the fluid flow, it can be stored using O a. pressure relief valve. O b. pressure reducing valve. O C. accumulator. O d. pressure absorbing valve.arrow_forwardWhat kind of circuit balancing valve is used in the hot and chilled water piping? a. balancing globe valve b. shut-off balancing valve c. pressure balancing valve d. pressure by-pass valvearrow_forward17. Which of the following relief valves is designed to vent refrigerant under excessive pressure and then close when the system pressure has been lowered? A. Fusible plug. B. Manifold valve. ytor C. Rupture disc. D. Spring-loaded relief valve. e quicaarrow_forward
- Pleasearrow_forwardWhat will happen when the pressure at any point inside a centrifugal pump goes below the vapor pressure corresponding to the temperature of the liquid a. priming b. turbulent flow c. cavitation d. laminar flowarrow_forwardPressure relief valves: Select one: a. Open manually upon overloading in pressure O b. Open automatically upon overloading in pressure c. Two directional valve d. Oil flow control valvearrow_forward
- Blocked suction cylinder unloading is accomplished by A. keeping the suction valve closed. B. closing the discharge. C. closing the suction service valve. D. using a device in the low-pressure side of the system to close it off.arrow_forwardSuction accumulatorarrow_forwardLeaks that occur only when the unit is in operation are called ______dependent leaks.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license