Refrigeration and Air Conditioning Technology (MindTap Course List)
8th Edition
ISBN: 9781305578296
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 33, Problem 25RQ
The temperature of the water at the outlet of a three-way mixing valve will most likely be
A. equal to the temperature of the water at the hot water inlet.
B. lower than the temperature of the water at the cold water inlet.
C. higher than the temperature of the water at the hot water inlet.
D. higher than the temperature of the water at the cold water inlet.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
1. When the pressure of the evaporator chamber is decreased, the boiling point of the solutions inside the chamber will:
2. It states that for a given concentration, the boiling point of the solution is a linear function of the boiling point of the solvent.
a.Boiling point rise
b.Enthalpy-concentration chart
c.Duhring's rule
d.Dalton's law
3.
Draft a sketch of this system describe below
What kind of circuit balancing valve is used in the hot and chilled water piping?
a. balancing globe valve
b. shut-off balancing valve
c. pressure balancing valve
d. pressure by-pass valve
Chapter 33 Solutions
Refrigeration and Air Conditioning Technology (MindTap Course List)
Ch. 33 - A hydronic heating system uses ______to move heat...Ch. 33 - Describe a zone in a hydronic heating system.Ch. 33 - Name four sources of heat commonly used for...Ch. 33 - Give three reasons that air is detrimental to a...Ch. 33 - Explain the difference between a wet-base and a...Ch. 33 - Where is air vented from a hydronic heating...Ch. 33 - The "point of no pressure change" is located at...Ch. 33 - The purpose of a limit control in a boiler is to...Ch. 33 - The device that relieves the pressure in a boiler...Ch. 33 - Describe the function of a low-water cutoff.
Ch. 33 - The relief valve setting for a typical...Ch. 33 - Describe how an air cushion tank functions in a...Ch. 33 - True or False: City water does not contain air.Ch. 33 - State two ways that air can get into a hydronic...Ch. 33 - The most common type of pump used for hydronic...Ch. 33 - Another term for pump pressure is feet of _______.Ch. 33 - Two types of zone control valves are the _____and...Ch. 33 - Why must expansion be considered when sizing...Ch. 33 - How is expansion in hot water pipes handled?Ch. 33 - Sketch the following systems: one pipe, two-pipe...Ch. 33 - Describe the advantage of a two-pipe...Ch. 33 - The pressure differential bypass valve is most...Ch. 33 - What is the heat output, in Btu/h, of a terminal...Ch. 33 - In a primary-secondary pumping arrangement, the...Ch. 33 - The temperature of the water at the outlet of a...Ch. 33 - A tankless water-heating system gets its heat from...Ch. 33 - How much of the sun's energy actually reaches the...Ch. 33 - The varying intensity of the sun's energy that...Ch. 33 - Drain-down systems would best be used in which...Ch. 33 - Why are solar systems intended to be used as a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When an evaporator experiences a heat- load increase,the suction pressureA. remains constant.B. decreases.C. varies up and down.D. increases.arrow_forwardWhich is the most accurate description of one of the system's processes? A Fluid moves from the secondary pipes into the ground. B Fluid moves from the primary pipe into the building. Fluids circulate separately inside both pipes. D Fluid moves from the secondary pipe through the heat exchanger to the primary pipe.arrow_forwardWhich one of the following statement is correct for steam nozzle? a. Outlet velocity of the steam is greater than inlet velocity of the steam b. Work done by the steam nozzle O C. The height difference between inlet and outlet nozzle is more o d. Heat is rejected by the steam nozzlearrow_forward
- 2. (i) Which of the following is not a centrifugal fan design? A. Fan array. B. Roof ventilator. C. Axial fan. D. Utility set. (ii) Which are advantages of fan arrays? Select all that apply. A. They offer redundancy. B. They are compact in length. C. They operate at lower speed.arrow_forwardWhen two fluids differ in densities, which of the following will always occur?A. The denser fluid will always stay at the bottom of the container.B. The denser fluid is heavier in mass if the volume of the liquids is equal.C. The lighter fluid experiences more vapor pressure than the denser fluid.D. The lighter fluid has more tendency to exhibit capillary movement.arrow_forwardPlease show complete solution, and if possible a sketch of diagram. Thank you. Will like automatically ofr correct answer.arrow_forward
- The evaporator is also known as the cooling coil, because the purpose of the evaporator is to absorb heatarrow_forwardGive me correct options with explanation please solve all questions thanksarrow_forwardThe thermocouple couldn't be directly used for temperature measurement, unless a reference point is defined. This reference point is: Select one: O a. The boiling temperature. b. All of the above. c. The ambient temperature. d. The mixture of ice-water temperature.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Hydronics Step by Step; Author: Taco Comfort Solutions;https://www.youtube.com/watch?v=-XGNl9kppR8;License: Standard Youtube License