Physics For Scientists And Engineers With Modern Physics, 9th Edition, The Ohio State University
9th Edition
ISBN: 9781305372337
Author: Raymond A. Serway | John W. Jewett
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 33, Problem 56P
(a)
To determine
The ratio of the amplitude of the output voltage to that of the input voltage is
(b)
To determine
The value of the ratio as the frequency decreases towards zero.
(c)
To determine
The value of ratio as the frequency increases without limit.
(d)
To determine
The frequency at which the ratio will be one half.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
. A capacitor of capacitance 80 µF is giving supply voltage V= 10 Sin ωt to one end of an oscillator. How can you evaluate the peak voltage of the circuit, if ω is changing from 10 to 100 rad/sec? Evaluate the difference between the peak values during the change of ω from 10 to 100 rad/sec. The capacitor acts an open circuit here. Justify your answer?
A 2.44 kΩ resistor is connected to an AC voltage source with an rms voltage of 230 V.
a)What is the maximum potential difference across the resistor (in V)?
b)What is the maximum current through the resistor (in A)?
c)What is the rms current through the resistor (in A)?
d)What is the average power dissipated by the resistor (in W)?
Impedance plethysmography is a technique that can be used to detect thrombosis—the presence of clots in a blood vessel—by measuring the electrical resistance of a limb, such as the calf of the leg. In a typical clinical setting, a current of 200 mA is passed through the leg from the upper thigh to the foot. The voltage is measured at two points along the calf separated by 13 cm.a. If the voltage measured is 17 mV, what is the resistance of the calf between the electrodes?b. If the average calf diameter between the electrodes is 12 cm, what is the average resistivity of this part of the leg?
Chapter 33 Solutions
Physics For Scientists And Engineers With Modern Physics, 9th Edition, The Ohio State University
Ch. 33.2 - Consider the voltage phasor in Figure 32.4, shown...Ch. 33.3 - Consider the AC circuit in Figure 32.8. The...Ch. 33.4 - Consider the AC circuit in Figure 32.11. The...Ch. 33.4 - Consider the AC circuit in Figure 32.12. The...Ch. 33.5 - Label each part of Figure 32.16, (a), (b), and...Ch. 33.6 - Prob. 33.6QQCh. 33.7 - Prob. 33.7QQCh. 33 - Prob. 1OQCh. 33 - Prob. 2OQCh. 33 - Prob. 3OQ
Ch. 33 - Prob. 4OQCh. 33 - Prob. 5OQCh. 33 - Prob. 6OQCh. 33 - Prob. 7OQCh. 33 - A resistor, a capacitor, and an inductor are...Ch. 33 - Under what conditions is the impedance of a series...Ch. 33 - Prob. 10OQCh. 33 - Prob. 11OQCh. 33 - Prob. 12OQCh. 33 - Prob. 13OQCh. 33 - Prob. 1CQCh. 33 - Prob. 2CQCh. 33 - Prob. 3CQCh. 33 - Prob. 4CQCh. 33 - Prob. 5CQCh. 33 - Prob. 6CQCh. 33 - Prob. 7CQCh. 33 - Prob. 8CQCh. 33 - Prob. 9CQCh. 33 - Prob. 10CQCh. 33 - Prob. 1PCh. 33 - (a) What is the resistance of a lightbulb that...Ch. 33 - Prob. 3PCh. 33 - Prob. 4PCh. 33 - Prob. 5PCh. 33 - Prob. 6PCh. 33 - Prob. 7PCh. 33 - Prob. 8PCh. 33 - Prob. 9PCh. 33 - Prob. 10PCh. 33 - Prob. 11PCh. 33 - Prob. 12PCh. 33 - An AC source has an output rms voltage of 78.0 V...Ch. 33 - Prob. 14PCh. 33 - Prob. 15PCh. 33 - Prob. 16PCh. 33 - Prob. 17PCh. 33 - An AC source with an output rms voltage of 86.0 V...Ch. 33 - Prob. 19PCh. 33 - Prob. 20PCh. 33 - Prob. 21PCh. 33 - Prob. 22PCh. 33 - What is the maximum current in a 2.20-F capacitor...Ch. 33 - Prob. 24PCh. 33 - In addition to phasor diagrams showing voltages...Ch. 33 - Prob. 26PCh. 33 - Prob. 27PCh. 33 - Prob. 28PCh. 33 - Prob. 29PCh. 33 - Prob. 30PCh. 33 - Prob. 31PCh. 33 - A 60.0-ft resistor is connected in series with a...Ch. 33 - Prob. 33PCh. 33 - Prob. 34PCh. 33 - A series RLC circuit has a resistance of 45.0 and...Ch. 33 - Prob. 36PCh. 33 - Prob. 37PCh. 33 - An AC voltage of the form v = 90.0 sin 350t, where...Ch. 33 - Prob. 39PCh. 33 - Prob. 40PCh. 33 - Prob. 41PCh. 33 - A series RLC circuit has components with the...Ch. 33 - Prob. 43PCh. 33 - Prob. 44PCh. 33 - A 10.0- resistor, 10.0-mH inductor, and 100-F...Ch. 33 - Prob. 46PCh. 33 - Prob. 47PCh. 33 - Prob. 48PCh. 33 - The primary coil of a transformer has N1 = 350...Ch. 33 - A transmission line that has a resistance per unit...Ch. 33 - Prob. 51PCh. 33 - Prob. 52PCh. 33 - Prob. 53PCh. 33 - Consider the RC highpass filter circuit shown in...Ch. 33 - Prob. 55PCh. 33 - Prob. 56PCh. 33 - Prob. 57APCh. 33 - Prob. 58APCh. 33 - Prob. 59APCh. 33 - Prob. 60APCh. 33 - Prob. 61APCh. 33 - Prob. 62APCh. 33 - Prob. 63APCh. 33 - Prob. 64APCh. 33 - Prob. 65APCh. 33 - Prob. 66APCh. 33 - Prob. 67APCh. 33 - Prob. 68APCh. 33 - Prob. 69APCh. 33 - (a) Sketch a graph of the phase angle for an RLC...Ch. 33 - Prob. 71APCh. 33 - Prob. 72APCh. 33 - A series RLC circuit contains the following...Ch. 33 - Prob. 74APCh. 33 - Prob. 75APCh. 33 - A series RLC circuit in which R = l.00 , L = 1.00...Ch. 33 - Prob. 77CPCh. 33 - Prob. 78CPCh. 33 - Prob. 79CPCh. 33 - Figure P33.80a shows a parallel RLC circuit. The...Ch. 33 - Prob. 81CP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- Consider the Filter circuit shown in Figure P33.56. (a) Show that the ratio of the amplitude of the output voltage to that of the input voltage is to that of input voltage is VoutVin=1/CR2+(1C)2 (b) What value does this ratio approach as the frequency decreases toward zero? (c) What value does this ratio approach as the frequency increases without limit? (d) At what frequency is the ratio equal to one-half?arrow_forward(a) What is the resistance of a light bulb that uses an average power of 75.0 W when connected to a 60.0-Hz power source having a maximum voltage of 170. V? (b) What is the resistance of a 100.-W lightbulb?arrow_forwardIn a purely inductive AC circuit as shown in Figure P21.15, Vmax = 100. V. (a) The maximum current is 7.50 A at 50.0 Hz. Calculate the inductance L. (b) At what angular frequency is the maximum current 2.50A? Figure p21.15arrow_forward
- An inductor and a resistor are connected in series across an AC source as in Figure OQ33.1. Immediately after the switch is closed, which of the following statements is true? (a) The current in the circuit is V/R. (b) The voltage across the inductor is zero, (c) The current in the circuit is zero, (d) The voltage across the resistor is V (e) The voltage across the inductor is half its maximum value.arrow_forwardAn AC source with Vmax = 150 V and f = 50.0 Hz is connected between points a and d in Figure P32.16. Calculate the maximum voltages between (a) points a and b, (b) points b and c, (c) points c and d, and (d) points b and d. Figure P32.16 Problems 16 and 51.arrow_forwardIn the AC circuit shown in Figure P32.3, R = 70.0 and the output voltage of the AC source is Vmax sin t. (a) If VR = 0.250 Vmax for the first time at t = 0.0100 s, what is the angular frequency of the source? (b) What is the next value of t for which VR = 0.250 Vmax? Figure P32.6 Problem 3 and 5.arrow_forward
- An audio amplifier, represented by the AC I source and resistor in Figure P33.7, delivers to the speaker alternating voltage at audio frequencies. If the source voltage has an amplitude of 15.0 V, R = 8.20 . and the speaker is equivalent to a resistance of 10.4 . what is the time-averaged power transferred to it?arrow_forwardAn ac source of voltage amplitude 100 V and frequency 1.0 kHz drives an PLC series circuit with R=20, L = 4.0 mH, and C=50F . (a) Determine the rms current through the circuit, (b) What are the rms voltages across the three elements? (c) What is the phase angle between the emf and the current? (d) What is the power output of the source? (e) What is the power dissipated in the resistor?arrow_forwardIn an RLC series circuit, the voltage amplitude and frequency of the source are 100 V and 500 Hz, respectively, an R = 5O0. L=0.20H, and C=2.0F . (a)What is the impedance of the circuit? (b) What is the amplitude of the current from the source? (C) If the emf of the source Is given by v(tt)=(100V)sin , how does the current vary with time? (d) Repeat the calculations with C changed to 0.20F .arrow_forward
- The resistor in Figure P32.49 represents the midrange speaker in a three-speaker system. Assume its resistance to be constant at 8.00 . The source represents an audio amplifier producing signals of uniform amplitude Vmax = 10.0 V at all audio frequencies. The inductor and capacitor are to function as a band-pass filter with Vout/Vin=12 at 200 Hz and at 4.00 103 Hz. Determine the required values of (a) L and (b) C. Find (c) the maximum value of the ratio Vout/Vin; (d) the frequency fo at which the ratio has its maximum value; (e) the phase shift between vin and vout at 200 Hz, at fo, and at 4.00 103 Hz; and (f) the average power transferred to the speaker at 200 Hz, at f0, and at 4.00 103 Hz. (g) Recognizing that the diagram represents an RLC circuit driven by an AC source, find its quality factor. Figure P32.49arrow_forwardRemove the capacitor from the circuit in the figure and set R = 151 N, L = 230 mH, fa 60.0 Hz, and ɛm = 42.0 V. What are (a) Z, (b) p, and (c) I? R C ll (a) Number 174 Units (b) Number Units ° (degrees) -40.2 (c) Number 0.207 Units Aarrow_forwardA 300. Q resistor is connected in series with a 4.00 F capacitor and a sinusoidal source of emf with Vrms = 40.0 V. a) Draw a phasor diagram showing the appropriate relationship among the voltage phasors across each of the three elements and the (single) current phasor. b) At what frequency will the amplitude of the potential difference across the capacitor equal the amplitude of the potential difference across the resistor? c) What is the rms current through the circuit at the frequency from part (b)?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Physics for Scientists and Engineers, Technology ...
Physics
ISBN:9781305116399
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
College Physics
Physics
ISBN:9781305952300
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Introduction To Alternating Current; Author: Tutorials Point (India) Ltd;https://www.youtube.com/watch?v=0m142qAZZpE;License: Standard YouTube License, CC-BY