Solve part a of Prob. 3.78, assuming that two 15-N vertical forces have been added, one acting upward at A and the other downward at C.
(a)
The net couple acting on the rectangular co-ordinates.
Answer to Problem 3.79P
The net couple acting on the rectangular co-ordinates is
Explanation of Solution
Write the equation of the couple acting at the reactangular side
Here, moment of couple at the point
Substitute
Write the equation of the couple acting at the reactangular side
Here, moment of couple at the point
Substitute
Write the equation of the couple vector acting at the reactangular co-ordinates at point
Here, the projection angle is
Substitute
Write the equation of the couple vector acting at the reactangular co-ordinates at point
Substitute
Sketch the moment of additional couple is added to the moment about
Write the equation of the additional couple vector acting at the point
Here, the additional couple vector formed by the force at the point
The negative sign of the force shows that the force acting downward direction.
Substitute
Conclusion:
Write the equation for the net couple acting on the rectangular co-ordinates.
Adding the equations (I), (II), and (III) to obtained the net couple.
Write the equation for the magnitude of net couple.
Therefore, the net couple acting on the rectangular co-ordinates is
(b)
The direction of the two forces acting on the point
Answer to Problem 3.79P
The direction of the two forces acting on the point
Explanation of Solution
Write the equation for direction of the moment of couple formed by the forces at point
Here, the angle formed by the moment of couple due to the force located at the point
Rewrite the equation for
Write the equation for direction of the moment of couple formed by the forces at point
Here, the angle formed by the moment of couple due to the force located at the point
Rewrite the equation for
Write the equation for direction of the moment of couple formed by the forces at point
Here, the angle formed by the moment of couple due to the force located at the point
Rewrite the equation for
Conclusion:
Substitute
Substitute
Substitute
Therefore, the direction of the two forces acting on the point
Want to see more full solutions like this?
Chapter 3 Solutions
VECTOR MECHANICS FOR ENGINEERS: STATICS
- An 8-m long cantilever beam is loaded with vertical forces A = 60 kN and B = 108 kN, separated by a distance d = 5.6 m, as shown. Replace the two forces with a single equivalent force R and determine the distance x-bar (x¯) from the left end of the beam to the line of action of R.arrow_forwardDetermine the horizontal and vertical components of force that the pins at A and B exert on the frame. 4.1 The magnitude of the horizontal component Ax at the hinged support A is Blank 1 kN. 4.2 The magnitude of the vertical component Ay at the hinged support A is Blank 2 kN. 4.3 The magnitude of the horizontal component Bx at the hinged support B is Blank 3 kN. 4.4 The magnitude of the vertical component By at the hinged support B is Blank 4 kN.arrow_forward4. The block shown is acted on by its weight W=400 lb, a horizontal F=600 lb, and the pressure P exerted by the inclined plane. The resultant R of these forces is parallel to the incline. Determine the values of P and R.arrow_forward
- A couple M and three forces P-6 lb, Q-27 lb, and R = 46 lb shown are applied to an angle bracket as shown. a 14 in and b-6.5 in. First, reduce the three forces to an equivalent set of forces Bz, By and couple CB at B. Second, determine the magnitude (with the correct sign, (+) for counter-clockwise and (-) for clockwise) of the couple M so that the final equivalent system has zero couple and consisting only of forces at B NOTE: Give the answer up to THREE significant digits. M P a Q 60° b Rarrow_forwardNeeds Complete solution with 100 % accuracy.arrow_forward45 N Ans. (a) 34 N, 0=280 (b) dRA = 11.64 mm from B to the left; dRc3D62 mm below B 36 Dr. M.S. Meddah 3.116 A 160-N motor is mounted on the floor. Find the resultant of the weight and the forces exerted on the belt, and determine where the line of action of the resultant intersects the floor. 700 N 30° 50 mm -300 N 50 mm Final result: Resultant, R = 925.92 N and 0 = 11.840 x= -582.22 mm i.e. resultant intersects the floor 582.22 mm to the left of the vertical centerline through O. 37arrow_forward
- A dirigible is tethered by a cable attached to its cabin at B. If the tension in the cable is 1040 N, replace the force exerted by the cable at B with an equivalent system formed by two parallel forces applied at A and C. A B 6.7 m '4 m 60° Darrow_forwardThe bracket, which is fastened to a wall by anchor bolts at A and B, is loaded by the force P = 140 N and the couple C = 180 N · m. Replace P and C with (a) an equivalent force-couple system, the force of which acts at A; and (b) two vertical forces, one acting at A and the other at B.arrow_forwardQ3) Determine the maximum weight of block A for which the maximum tension in cable CD does not exceed 160 N B 60 13 Determine the resultant of the coplanar force system shown in (FIG. Q1) and locate it with respect to point A? 360 N 500 N 220 Narrow_forward
- The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a thrust hinge at A, a slider hinge at B, and the cable CD. Find the force in the cable and the magnitudes of the hinge reactions.arrow_forwardReplace the wrench shown with an equivalent system consisting of two forces perpendicular to the y axis and applied respectively at A amd B.arrow_forward0.4 m B A 4.8 m 0.6 m 5.6 m E F 4.8 m x PROBLEM 3.51 A farmer uses cables and winch pullers B and E to plumb one side of a small barn. If it is known that the sum of the moments about the x axis of the forces exerted by the cables on the barn at Points A and D is equal to 7.6 kN-m, determine the magnitude of TDE when TAB = 1.02 kN. IDE = 1.14 KNarrow_forward
- International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L