EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 9780100793439
Author: KALPAKJIAN
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 33, Problem 15RQ
To determine
Explain why graphite and molybdenum disulfide are effective solid lubricants.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Metallography Questions
A. Explain why metallographic samples must be kept cool during cutting and grinding
B. Explain the purpose of mounting samples in materials such as Bakelite.
A form of boron nitride (BN) known as hexagonal boron nitride is used as a solid lubricant. Explain how this may be possible by comparing this situation with that encountered in two forms of carbon, namely diamond and graphite.
There are two common manufacturing processes that create long metal parts with
a constant cross-section. With the aid of diagrams, explain these two processes
and identify the similarities and differences between them.
Chapter 33 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 33 - What is tribology?Ch. 33 - Explain what is meant by (a) surface texture and...Ch. 33 - List and explain the types of defects typically...Ch. 33 - Define the terms (a) roughness, and (b) waviness.Ch. 33 - Explain why the results from a profilometer are...Ch. 33 - Prob. 6RQCh. 33 - List the types of wear generally observed in...Ch. 33 - Define the terms wear, friction, and lubricant.Ch. 33 - How can adhesive wear be reduced? Abrasive wear?Ch. 33 - Prob. 10RQ
Ch. 33 - Explain the functions of a lubricant in...Ch. 33 - Prob. 12RQCh. 33 - Prob. 13RQCh. 33 - Describe the factors involved in lubricant...Ch. 33 - Prob. 15RQCh. 33 - Prob. 16QLPCh. 33 - Explain the significance of the fact that the...Ch. 33 - Prob. 18QLPCh. 33 - Explain why identical surface-roughness values do...Ch. 33 - Prob. 20QLPCh. 33 - Prob. 21QLPCh. 33 - Prob. 22QLPCh. 33 - Prob. 23QLPCh. 33 - Comment on the surface roughness of various parts...Ch. 33 - Prob. 25QLPCh. 33 - Do the same as for Problem 33.25, but for surface...Ch. 33 - Describe your observations regarding Fig. 33.7.Ch. 33 - Give the reasons that an originally round specimen...Ch. 33 - Prob. 29QLPCh. 33 - Explain the reason that the abrasive-wear...Ch. 33 - Prob. 31QLPCh. 33 - List the similarities and differences between...Ch. 33 - Explain why the types of wear shown in Fig. 33.11...Ch. 33 - List the requirements of a lubricant.Ch. 33 - List manufacturing operations in which high...Ch. 33 - List manufacturing operations in which high wear...Ch. 33 - Prob. 37QLPCh. 33 - Prob. 38QTPCh. 33 - A surface with a triangular sawtooth roughness...Ch. 33 - List the steps you would follow if you wished to...Ch. 33 - Discuss the tribological differences between...Ch. 33 - Section 33.2 listed major surface defects. How...Ch. 33 - Describe your own thoughts regarding biological...Ch. 33 - Prob. 48SDPCh. 33 - Prob. 49SDPCh. 33 - Prob. 50SDPCh. 33 - Describe your thoughts on the desirability of...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Explain how macroscopic plasticity in metals occurs from the point of view of microscopic mechanisms (covered in the chapters indicated in the Callister book). (maximum of 5 lines, not counting the space for possible schematic figures)arrow_forwardCalculate the surface to volume ratio of nanomaterials obtained by breaking a cube of bulkmaterial into 8 small cubes of equal edge. The edge of the bulk cube is 6 cm.arrow_forward(c) Sketch a diagram showing impact energy as a function of temperature, of (i) 0.1% carbon steel; (ii) 1.0% carbon steel. Give the name of the observed phenomenon and explain how the behaviour would be expected to be different for bcc and fcc alloys.arrow_forward
- Explain the surface finishing operation in which stainless steel spoon is coated with silver.arrow_forwardQUESTION 1 (a) Powder Metallurgy (PM) enables the processing of materials with very high melting points, including refractory metals such as tungsten, molybdenum and tantalum. Such metals are very difficult to produce by melting and casting and are often very brittle in the cast state. As a manufacturing engineer, state and explain at least SIX (6) limitations of powder metallurgy that is not applicable in particular engineering industries. In a case where you were assigned to use powder metallurgy in metal forming, justify at least THREE (3) PM requirements. (b) A coil of sheet metal is placed in a furnace and annealed in order to improve its ductility. Nonetheless, it is found that the sheet metal has a lower limiting drawing (LDR) than it had before the annealing process. Describe the meaning of LDR and explain the reasons for this behaviour by referring to the microstructure and materials' properties point of view for different types of materials. In addition, discuss the process…arrow_forwardDescribe and discuss, using sketches, the difference between substitution andinterstitial solid solutions of metal alloysarrow_forward
- What is the difference between coarse and fine pearlite in terms of (1) microstructure and (2) mechanical properties? explain why the difference exist in (1) and (2).arrow_forwardAnalyse, using an accredited data source, the microstructures of non-processed and processed metallic materials to correctly identify the material, including how the processing history affects the mechanical properties of the materials.arrow_forwardneed a good explanatory answer. 14. Diamond is harder than steel. -Do you believe the statement above is a good or bad hypothesis? Explain.arrow_forward
- 3) What are high density and hard alpha inclusions in titanium metallurgy? Explain the method of removing them from titanium.arrow_forwardWhat are Heisler charts? Explain its significance.arrow_forwardExplain and discuss the differences on the mechanical properties/behaviours of i) metals, ii) ceramics, iii) polymers and iv) composite materials by drawing figures.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Types of Manufacturing Process | Manufacturing Processes; Author: Magic Marks;https://www.youtube.com/watch?v=koULXptaBTs;License: Standard Youtube License