The identity of the element with the given ground-state electron configuration should be identified. Concept Introduction: An orbital is a region of space in which electrons are filled. It can hold up to two electrons. An atomic orbital is the region of space in which the probability of finding the electrons is highest. It is subdivided into 4 orbitals such as s , p , d a n d f orbitals which depend upon the number of electrons present in the nucleus of a particular atom. The orders in which orbitals are filled by the electrons are governed by three basic principles. 1. Aufbau principle: In the ground state of an atom, an electron enters the orbital with lowest energy first and subsequent electrons are fed in the order of increasing energies. The word 'aufbau' in German means 'building up'. Here, it refers to the filling up of orbitals with electrons. 2. Pauli exclusion principle: As an orbital can contain a maximum of only two electrons, the two electrons must have opposing spins. 3. Hund’s rule: Every orbital in a subshell is singly occupied with one electron before any one orbital is paired and all electrons in singly occupied orbitals have the same spin. The electron configuration is the distribution of electrons of an atom in atomic orbitals. By following these three principles, electronic configuration of a particular atom is written. To identify: Identify the symbol of the element with the given ground-state electron configuration [ Xe ] 6 s 2 4 f 14 5 d 10 6 p 5

Question

Want to see the full answer?

Answer 1

Question

Chapter 3.10, Problem 11PPB

Interpretation Introduction

Interpretation:

The identity of the element with the given ground-state electron configuration should be identified.

Concept Introduction:

An orbital is a region of space in which electrons are filled. It can hold up to two electrons.

An atomic orbital is the region of space in which the probability of finding the electrons is highest. It is subdivided into 4 orbitals such as s, p, d and f orbitals which depend upon the number of electrons present in the nucleus of a particular atom.

The orders in which orbitals are filled by the electrons are governed by three basic principles.

1. Aufbau principle: In the ground state of an atom, an electron enters the orbital with lowest energy first and subsequent electrons are fed in the order of increasing energies. The word 'aufbau' in German means 'building up'. Here, it refers to the filling up of orbitals with electrons.

2. Pauli exclusion principle: As an orbital can contain a maximum of only two electrons, the two electrons must have opposing spins.

3. Hund’s rule: Every orbital in a subshell is singly occupied with one electron before any one orbital is paired and all electrons in singly occupied orbitals have the same spin.

The electron configuration is the distribution of electrons of an atom in atomic orbitals. By following these three principles, electronic configuration of a particular atom is written.

To identify: Identify the symbol of the element with the given ground-state electron configuration [Xe]6s24f145d106p5

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

There is an instrument in Johnson 334 that measures total-reflectance x-ray fluorescence (TXRF) to do elemental analysis (i.e., determine what elements are present in a sample). A researcher is preparing a to measure calcium content in a series of well water samples by TXRF with an internal standard of vanadium (atomic symbol: V). She has prepared a series of standard solutions to ensure a linear instrument response over the expected Ca concentration range of 40-80 ppm. The concentrations of Ca and V (ppm) and the instrument response (peak area, arbitrary units) are shown below. Also included is a sample spectrum. Equation 1 describes the response factor, K, relating the analyte signal (SA) and the standard signal (SIS) to their respective concentrations (CA and CIS). Ca, ppm V, ppm SCa, arb. units SV, arb. units 20.0 10.0 14375.11 14261.02 40.0 10.0 36182.15 17997.10 60.0 10.0 39275.74 12988.01 80.0 10.0 57530.75 14268.54 100.0…

A mixture of 0.568 M H₂O, 0.438 M Cl₂O, and 0.710 M HClO are enclosed in a vessel at 25 °C. H₂O(g) + C₁₂O(g) = 2 HOCl(g) K = 0.0900 at 25°C с Calculate the equilibrium concentrations of each gas at 25 °C. [H₂O]= [C₁₂O]= [HOCI]= M Σ M

What units (if any) does the response factor (K) have? Does the response factor (K) depend upon how the concentration is expressed (e.g. molarity, ppm, ppb, etc.)?