Delmar's Standard Textbook Of Electricity
7th Edition
ISBN: 9781337900348
Author: Stephen L. Herman
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 30, Problem 8RQ
To determine
The parameter that limits the amount of current flow through the armature when power is first applied to the motor.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A DPSK has the following data input: d(n) =101011010001
1. Find the output coded sequence and the carrier phase.
2. Recover the input data from the output coded sequence.
Q9 A single-phase transformer, 2500 / 250 V, 50 kVA, 50 Hz has the following parameters, the
Primary and secondary resistances are 0.8 ohm and 0.012 ohm respectively, the primary and
secondary reactance are 4 ohm and 0.04 ohm respectively and the transformer gives 96% maximum
efficiency at 75% full-load. The magnetizing component of-load current is 1.2 A on 2500 V side. 1-
Draw the equivalent circuit referred to primary (H.V side) and inserts all the values in it 2- Find out
Ammeter, voltmeter and wattmeter readings on open-circuit and short-circuit test. If supply is given
to 2500 V side in both cases. Ans. O.C. Test (Vo= 2500 V, lo=1.24 A, Wo=781.25 w) S.C. Test (Vsc
=164.924 V, Isc =20 A, Wsc =800 w )
A modulating signal f(t) is bandlimited to 5.5 kHz is sampled at a rate of 15000 samples/sec.
The samples are quantized into 1024 levels. Calculate transmission bandwidth if the following
modulation types are used for signal transmission:
1-ASK, QAM
2-QPSK, 8-PSK
3-FSK, 8-FSK with Af = 20 kHz
Chapter 30 Solutions
Delmar's Standard Textbook Of Electricity
Ch. 30 - Prob. 1RQCh. 30 - Prob. 2RQCh. 30 - Prob. 3RQCh. 30 - Prob. 4RQCh. 30 - What type of motor is known as a constant-speed...Ch. 30 - What is CEMF?Ch. 30 - Prob. 7RQCh. 30 - Prob. 8RQCh. 30 - Prob. 9RQCh. 30 - What type of motor should never be operated at no...
Ch. 30 - Prob. 11RQCh. 30 - What is the most common way of changing the...Ch. 30 - Prob. 13RQCh. 30 - Prob. 14RQCh. 30 - What device is used to disconnect power to the...Ch. 30 - Prob. 16RQCh. 30 - Who was the first person to establish a...Ch. 30 - One horsepower is equal to how many W?Ch. 30 - A motor is operating a load that requires a torque...Ch. 30 - The motor in Question 19 is connected to a 250-VDC...Ch. 30 - Prob. 1PA
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q10 The full-load copper loss on the H.V. side of 100KVA, 11000/317 V, single-phase transformer is 0.62 kw and on the L.V. side is 0.48 kW. i) Calculate R1, R2 in ohms ii) Find X1,X2,if the percentage equivalent reactance is 4%, and reactance is divided in same proportion as resistance. Ans, 27.30, 0.175), 0.00482 . (7.5)arrow_forwardFind the binary sequence, for the following Differential Manchester code.arrow_forwardQ2- What are the parameters and loss that can be determined during open-circuit test of singlephase transformer. Draw the circuit diagram of open-circuit test and explain how can you calculate the Parameters and loss.arrow_forward
- Q6- the open circuit and short circuit tests on a 10 KVA, 125/250 v, 50 Hz single phase transformer gave the following results: O.C. Test: 125 V,0.6 A, 50 W ( on L.V.) S.C. Test: 20 V, 40 A, 177.78 W (on H.V. side) Calculate: i) Copper losses on half load ii) Full load efficiency at 0.8 leading p.f. iii) Half load efficiency at 0.8 leading p.f. iv) Regulation at full load at 0.9 leading p.f. Ans: 44.445 W, 97.23%, 97.69%, -1.8015%arrow_forwardQ3-A two-winding transformer has a primary winding with 208 turns and a secondary winding with 6 turns. The primary winding is connected to a 4160V system. What is the secondary voltage at no load? What is the current in the primary winding with a 50-amp load connected to the secondary winding? What is the apparent power flowing in the primary and secondary circuits? Ans. 120 V, 1.44 A, 6000 VAarrow_forwardQ12- A three phase transformer 3300/400 V,has D/Y connected and working on 50Hz. The line current on the primary side is 12A and secondary has a balanced load at 0.8 lagging p.f. Determine the i) Secondary phase voltage ii) Line current iii) Output power Ans. (230.95 V, 99.11 A, 54.94 kW)arrow_forward
- Q1- A single phase transformer consumes 2 A on no load at p.f. 0.208 lagging. The turns ratio is 2/1 (step down). If the loads on the secondary is 25 A at a p.f. 0.866 lagging. Find the primary current and power factor.arrow_forwardQ7- A 5 KVA, 500/250 V,50 Hz, single phase transformer gave the following reading: O.C. Test: 250 V,2 A, 50 W (H.V. side open) S.C. Test: 25 V10 A, 60 W (L.V. side shorted) Determine: i) The efficiency on full load, 0.8 lagging p.f. ii) The voltage regulation on full load, 0.8 leading p.f. iii) Draw the equivalent circuit referred to primary and insert all the values it.arrow_forwardQ4- A single phase transformer has 350 primary and secondary 1050 turns. The primary is connected to 400 V,50 Hz a.c. supply. If the net cross sectional area of core is 50 cm2, calculate i) The maximum value of the flux density in the core. ii) The induced e.m.f in the secondary winding. Ans: 1.029 T, 1200Varrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:9781337900348
Author:Stephen L. Herman
Publisher:Cengage Learning