Operations Management: Processes And Supply Chains (12th Global Edition) - Does Not Include Mylab Operations Management
12th Edition
ISBN: 9780134890357
Author: Lee J. Krajewski, Manoj K. Malhotra
Publisher: Pearson Global Edition
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 3, Problem 4P
Summary Introduction
Interpretation: A control chart is used to detect the variations in a process.
Concept introduction:
A mean control chart
R charts are utilized to monitor the variation of a procedure based on samples brought from the process at a provided period. Variable shiftsare measures and detected by R charts. To monitor the variation the processR charts control limits may be applied.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Management at Webster Chemical Company is concerned as to whether caulking tubes are being properly capped. If a significant proportion of the tubes are not being sealed, Webster is placing its
customers in a messy situation. Tubes are packaged in large boxes of 135. Several boxes are inspected, and the following numbers of leaking tubes are found:
View an example
Sample
1
2
3
Get more help.
4
Tubes
7
7
8
5
1
5
6
7
Calculate p-chart three-sigma control limits to assess whether the capping process is in statistical control.
The UCL, equals
1
Sample
8
8
9
10
11
12
13
14
Tubes
7
2
4
8
6
9
MacBook Pro
3
Sample
15
16
17
18
19
20
Total
Tubes
8
3
3
5
and the LCL equals (Enter your responses rounded to three decimal places. If your answer for LCL, is negative, enter this value as 0.)
3
6
104
Clear all
Check answer
O
snip
An e-commerce website has received some complaints on Billing errors. Managers ask the accounting department to monitor the
shipping process and make sure of the quality in their process. To monitor the process, for 10 consecutive weeks, they look into the
first 100 shipments and count the number of Billing errors as shown in table below:
45
52
6
3
63
7
8
9 10
1 6
1
2
Construct a two-sigma limit control chart to show whether the shipping process in this e-commerce firm needs any improvement or
performs at an acceptable level. (Round your answer to three decimal places.)
Week
1
2
3
Number of Billing errors.
5
1
3
Upper Control Limit
Lower Control Limit
Chapter 3 Solutions
Operations Management: Processes And Supply Chains (12th Global Edition) - Does Not Include Mylab Operations Management
Ch. 3 - Should a very pricey handcrafted object of beauty...Ch. 3 - Prob. 2DQCh. 3 - Prob. 3DQCh. 3 - Prob. 1PCh. 3 - Prob. 2PCh. 3 - Prob. 3PCh. 3 - Prob. 4PCh. 3 - Prob. 5PCh. 3 - Prob. 6PCh. 3 - Prob. 7P
Ch. 3 - Prob. 8PCh. 3 - Prob. 9PCh. 3 - Prob. 10PCh. 3 - Prob. 11PCh. 3 - Prob. 12PCh. 3 - Prob. 13PCh. 3 - Prob. 14PCh. 3 - Prob. 15PCh. 3 - Prob. 16PCh. 3 - Prob. 17PCh. 3 - Prob. 18PCh. 3 - Prob. 19PCh. 3 - Prob. 20PCh. 3 - Prob. 21PCh. 3 - Prob. 26PCh. 3 - Prob. 27PCh. 3 - Prob. 28PCh. 3 - Prob. 29PCh. 3 - Prob. 31PCh. 3 - Prob. 1AMECh. 3 - Prob. 2AMECh. 3 - Prob. 3AMECh. 3 - Prob. 4AMECh. 3 - Prob. 5AMECh. 3 - Prob. 1VCCh. 3 - Prob. 2VC
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, operations-management and related others by exploring similar questions and additional content below.Similar questions
- 2- Quality Control Charts A local brewery and bottling plant wants to keep track of the bottling filling equipment's accuracy, Bottles are to be filled with exactly 16 ounces of the drink. The following is data from the bottling equipment where 5 samples of bottles filled were pulled every hour and measured for actual quantity filled. 1- Calculate the UCL, LCL and mean for the X-bar and R data 2- Draw an X-Bar chart and a R chart. 3- Is this filling process in control or out of control? Hour X-bar R 1 16.05 .20 2 16.03 3 15.96 4 15.97 16.03 16.06 15.98 16.09 15.94 16.01 5 6 7 8 9 10 @n-5: A2 = 0.58, D3 =0, D4 = 2.11 .25 .62 .58 .71 .37 .46 .21 .35 .29arrow_forwardA distributor buys Tires from manufacturers. In his store, Phillip Johnson, the supplier quality manager for the distribution company, selects a tire at random which was received in the warehouse the prior day. Small imperfections (minor wears in trade, uneven surfaces, etc) are counted. Recent data show an average of six imperfections (nonconformities) in each sample. Using the formulas for a c chart, calculate the control limits and centerline for this situation. If management wants a process capability of five nonconformities per sample, will this supplier be able to meet that requirement?arrow_forwardFactors for Computing Control Chart Limits (3 sigma) Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced each day, the mean and the range of this diameter have been as follows: Day Mean x (mm) Range R (mm) 1 156.9 4.2 2 153.2 4.6 3 153.6 4.1 4 155.5 5.0 5 156.6 4.5 Part 4 c) What are the (UCLx) and (LCLx) using 3-sigma? (UCLx) = mm (round your response to two decimal places). (LCLx) = mmarrow_forward
- A manufacturer of precision machine parts produces round shafts for use in the construction of drill presses. The average diameter of a shaft is .56 inch. Inspection samples contain 6 shafts each. The average range of these samples is .006 inch. Determine the upper and lower x control chart limits.arrow_forwardAspen Plastics produces plastic bottles to customer order.The quality inspector randomly selects four bottles fromthe bottle machine and measures the outside diameter ofthe bottle neck, a critical quality dimension that determineswhether the bottle cap will fit properly. The dimensions(inch) from the last six samples are Assume that only these six samples are sufficient, and use thedata to determine control limits for an R- and an x-chart.arrow_forwardA manufacturer uses statistical process control to control the quality of the firm's products. Samples of 50 of Product A are taken, and a defective/acceptable decision is made on each unit sampled. For Product B, the number of flaws per unit is counted. What type(s) of control charts should be used? Select one: a. c-chart for A, mean and range charts for B b. p-chart for A , mean and range charts for B c. c-chart for both A and B d. p-chart for A, c-chart for B e. p-charts for both A and Barrow_forward
- DESIGNING A CONTROL CHART EXAMPLE Fujiyama Electronics, Inc. has been having difficulties with circuit boards purchased from an outside supplier. Unacceptable variability occurs between two drilled holes that are supposed to be 5 cm apart on the circuit boards. Thirty samples of 4 boards each were taken from shipments from the supplier as shown in the data listed below. Construct x and R charts for the process using the following data. DATA Sample No Samples 1 4.92 4.26 4.94 4.29 2 4.65 5.54 5.00 5.42 3 5.77 5.26 4.76 4.79 4 6.25 4.88 5.66 4.44 5 5.27 5.41 6.02 4.91 6 5.22 5.38 5.08 4.65 7 5.47 4.68 4.56 4.70 8 5.71 4.54 4.17 4.87 9 5.24 5.58 4.72 5.41 10 4.42 5.18 4.79 4.73 11 5.14 4.26 4.71 5.48 12 4.92 5.78 5.50 5.05 13 5.79 3.83 4.30 4.78 14 4.92 4.80 4.75 5.59 15 5.68…arrow_forwardIf there are 400 total defects from 8 samples, each sample consisting of 20 individual items in a production process, what is the fraction defective that can be used in a "p" chart for quality control purposes?arrow_forwardA metal fabricator produces connecting rods with an outer diameter that has a 1 ± 0.04 inch specification. A machine operator takes several sample measurements over time and determines the sample mean outer diameter to be 1.002 inches with a standard deviation of 0.009 inch. Calculate the process capability. 1.56 1.62 1.48 1.41 1.35arrow_forward
- In a fabric manufacturing factory, the quality control process using control charts from SPC. In an hour there are a total of 5 samples are taken each having 5 observations regarding the thickness of fabric in measured in millimeters. In a particular hour, the sample means (X-bar) are noted to be: 172.11, 219.51 . 208.24, 112.44 and 123.30 respectively. In the same sample, the corresponding ranges are: 13.1713.3815.34, 13.04, and 13.02 respectively What are the lower and upper control limits for the R chart?arrow_forwardA shirt manufacturer buys clothes by the 100-yard roll from a supplier. For setting a control chart to manage the irregularities (e.g., loose threads and tears), the following data were collected from a sample provided by the supplier. Sample 1 2 3 4 5 6 7 8 9 10 Irregularities 3 5 2 6 5 4 6 3 4 5 Which type of control chart should be used? Construct a control chart with two-sigma control limits. Suppose the next five rolls from the supplier had three, two, five, three, and seven irregularities. Is the supplier process under control? Explain and show workarrow_forwardThe Road King Tire Company in Birmingham wants to moni-tor the quality of the tires it manufactures. Each day the com-pany quality-control manager takes a sample of 100 tires, tests them, and determines the number of defective tires. The re-sults of 20 samples have been recorded as follows:Construct a p-chart for this process using 2 limits and for each of the last 30 weekdays are shown as follows:describe the variation in the process. Sample Defectives Sample Defectives1 14 11 182 12 12 103 9 13 194 10 14 205 11 15 176 7 16 187 8 17 188 14 18 229 16 19 2410 17 20 23arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Practical Management ScienceOperations ManagementISBN:9781337406659Author:WINSTON, Wayne L.Publisher:Cengage,
Operations ManagementOperations ManagementISBN:9781259667473Author:William J StevensonPublisher:McGraw-Hill Education
Operations and Supply Chain Management (Mcgraw-hi...Operations ManagementISBN:9781259666100Author:F. Robert Jacobs, Richard B ChasePublisher:McGraw-Hill Education
Purchasing and Supply Chain ManagementOperations ManagementISBN:9781285869681Author:Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. PattersonPublisher:Cengage Learning
Production and Operations Analysis, Seventh Editi...Operations ManagementISBN:9781478623069Author:Steven Nahmias, Tava Lennon OlsenPublisher:Waveland Press, Inc.
Practical Management Science
Operations Management
ISBN:9781337406659
Author:WINSTON, Wayne L.
Publisher:Cengage,
Operations Management
Operations Management
ISBN:9781259667473
Author:William J Stevenson
Publisher:McGraw-Hill Education
Operations and Supply Chain Management (Mcgraw-hi...
Operations Management
ISBN:9781259666100
Author:F. Robert Jacobs, Richard B Chase
Publisher:McGraw-Hill Education
Purchasing and Supply Chain Management
Operations Management
ISBN:9781285869681
Author:Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson
Publisher:Cengage Learning
Production and Operations Analysis, Seventh Editi...
Operations Management
ISBN:9781478623069
Author:Steven Nahmias, Tava Lennon Olsen
Publisher:Waveland Press, Inc.