Concept explainers
Consider a 2100-kg car cruising at constant speed of 70 km/h. Now the car starts to pass another car by accelerating to 110 km/h in 5 s. Determine the additional power needed to achieve this acceleration. What would your answer be if the total mass of the car were only 700 kg?
The additional power needed to achieve the acceleration.
If the total mass of the car is 700 kg, what would be the answer in order to achieve the acceleration?
Answer to Problem 50P
The additional power needed to achieve the acceleration is
If the total mass of the car is 700 kg, the answer in order to achieve the acceleration is
Explanation of Solution
Write the energy balance equation for a control volume when car cruising is taken as the system.
Here, the rate of energy transfer entering and leaving the system is
Since no energy is leaving the room,
Substitute 0 for
Here, the change in the internal energy of the system is
Rewrite Equation (II) when rate of work done on the system.
Here, velocity at inlet and outlet is
If the total mass of the car is 700 kg, calculate the additional power needed to achieve the acceleration.
Conclusion:
Substitute 2100 kg for m, 110 km/h for
Thus, the additional power needed to achieve the acceleration is
Substitute 700 kg for m, 110 km/h for
Thus, if the total mass of the car is 700 kg, the answer in order to achieve the acceleration is
Want to see more full solutions like this?
Chapter 2 Solutions
THERMODYNAMICS LLF W/ CONNECT ACCESS
Additional Engineering Textbook Solutions
Statics and Mechanics of Materials (5th Edition)
Applied Statics and Strength of Materials (6th Edition)
Fluid Mechanics Fundamentals And Applications
Machine Elements in Mechanical Design (6th Edition) (What's New in Trades & Technology)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Fluid Mechanics: Fundamentals and Applications
- A 16276 kg helicopter moves upward with a constant acceleration from rest to a height of 493 m. The spinning blades create an upward thrust of 352370 N that lifts the helicopter into the air. How long does it take the helicopter to reach the height of 493 m? t =arrow_forwardOne engine works with constant power P and the other one increases its power linearly with time. What is the ratio of the work done by the engines (engine two to engine one) if the second engine increased its power from zero to 3.6 P during the observed time?arrow_forward6. Determine the energy required to accelerate a 1300- kg car from 10 to 60 km/h on an uph road with a vertical rise of 40 m. 7. Determine the torque applied to the shaft of a car that transmits 450 hp and rotates at rate of 3000 rpm.arrow_forward
- A hydraulic elevator is lifting two women, a child, and a cat at a rate of 50 ft/min. If their combined mass is 282 Ibm and the mass of the elevator is 1250 lbm, what is the minimum power rating required? Express this quantity in units of Watts. The elevator is 78% efficient.arrow_forwardA 10-kg rock is thrown upward with a force of 280 N at a location where the local gravitational acceleration is 9.79 m/s2. Determine the acceleration of the rock, in m/s2.arrow_forwardThe elevator car, including passengers, has a mass of 1800 kg. Each floor of the building is separated by 4 m (i.e., the ground floor is at 0 m, the 1st floor is at 4 m, the 2nd floor is at 8 m, etc.) and the top floor is the 10th floor. The elevator goes up from the ground floor, starting at rest. It accelerates at a constant rate of 0.25 m/s2 up to the 5th floor, then decelerates at the same rate (acceleration of -0.25 m/s2 ) until coming to a stop at the 10th floor. a. At which floor (or, if you prefer, what height from the ground) does the elevator have the maximum total energy? b. Assuming that friction and drag forces are negligible, how much work is done by the tension force (in the cable that pulls the elevator up) in moving the elevator from the ground floor to the top floor? c. Assuming instead that friction and drag forces are constant over the entire ascension, and equal to 250 N, how much work is done by the tension force in moving the elevator from the ground floor to…arrow_forward
- An object initially at rest experiences a constant horizontal acceleration due to the action of a resultant force applied for 10 s. The work of the resultant force is 10 Btu. The mass of the object is 45 lb. Determine the constant horizontal acceleration in ft/s². ax i ft/s²arrow_forwardA mass of 7 kg undergoes a process during which velocity decreases from 32 m/s to 19m/s, while the elevation remain unchanged. The initial specific internal energy of the mass is 1.24 kJ/kg and the final specific internal energy is 2.08 kJ/kg. During the process, the mass receives 2 kJ of energy by heat transfer through its bottom surface and loses 0.8 kJ by heat transfer through its top surface. How much is the work in kJ? (hint: be consistent with units) ( 2 decimal places)arrow_forwardA 1380 kg block is being pulled across the floor by a rope which is wrapped around a motorized winch. The coefficient of kinetic friction between the block and the floor is 0.41, and the block moves at a constant speed of 1.34 m/s.What is the power output of the motor, in Watts (W)?Calculate the total work done by the winch if the box moves a total of 4.50 meters. Give your answer in Joules (J).arrow_forward
- A 7.0-kg block on a horizontal frictionless surface is attached to a light spring (force constant - 1.2 kN/m). The block is initially at rest at its equilibrium position when a force of magnitude P acting parallel to the surface is applied to the block, as shown. When the block is 8.0 cm from the equilibrium position, it has a speed of 0.80 m/s. How much work is done on the block by the force P as the block moves the 8.0 cm? xxxxxxxxarrow_forwardA power of 6 kW is supplied to the motor of a crane. The motor has an efficiency of 90%. With what constant speed does the crane lift an 800 lb weight. The correct answer is 1.5 m/s.arrow_forwardAn electric motor is used to drive the shaft of a small water pump. During a performance test, the torque on the motor shaft is found to be 5.549 N.m when the motor is drawing 687.12 W of electrical power. What's the rotational speed of the shaft in rpm?arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY