Concept explainers
(a)
The estimation of the resistivity and
(a)
Answer to Problem 28PQ
The estimation of the resistivity and conductivity of a roll of the pure copper pennies are
Explanation of Solution
The estimated values of pure substances are given in Table 28.2.
For the pure copper, the resistivity
Conclusion:
Therefore, the estimation of the resistivity and conductivity of a roll of the pure copper pennies are
(b)
The estimation of the resistance of the roll of pure copper pennies.
(b)
Answer to Problem 28PQ
The estimation of the resistance of the roll of pure copper pennies is
Explanation of Solution
The radius and the length of a stack of 50 pennies are
Write the relation for the resistance of the role of pure copper pennies.
Here,
Write the relation for the cross-sectional area of the copper penny.
Here,
Use equation (II) in equation (I) to get
Conclusion:
Substitute
Therefore, the estimation of the resistance of the roll of pure copper pennies is
(b)
The estimation of the resistance of the roll of pure aluminum pennies.
(b)
Answer to Problem 28PQ
The estimation of the resistance of the roll of pure aluminum pennies is
Explanation of Solution
Rewrite the equation (III) for the resistance of the aluminum pennies
Conclusion:
Substitute
Therefore, the estimation of the resistance of the roll of pure aluminum pennies is
Want to see more full solutions like this?
Chapter 28 Solutions
Physics for Scientists and Engineers: Foundations and Connections
- The quantity of charge q (in coulombs) that has passed through a surface of area 2.00 cm2 varies with time according to the equation q = 4t3 + 5t + 6, where t is in seconds. (a) What is the instantaneous current through the surface at t = 1.00 s? (b) What is the value of the current density?arrow_forwardUnreasonable Results (a) What current is needed to transmit 1.00 102 MW of power at 10.0kV? (b) Find the resistance of 1.00 km of wire that would cause a 0.0100% power loss. (c) What is the diameter of a 1.00-km-long copper wire having this resistance? (d) What is unreasonable about these results? (e) Which assumptions are unreasonable, or which premises are inconsistent?arrow_forwardAn aluminum wire 1.628 mm in diameter (14-gauge) carries a current of 3.00 amps, (a) What is the absolute value of the charge density in the wire? (b) What is the drift velocity of the electrons? (c) What would be the drift velocity if the same gauge copper were used instead of aluminum? The density of copper is 8.96 g/cm3 and thedensity of aluminum is 2.70 g/cm3. The molar mass ofaluminum is 26.98 g/mol and the molar mass of copper is 63.5 g/mol. Assume each atom of metal contributes one free electron.arrow_forward
- A regular tetrahedron is a pyramid with a triangular base and triangular sides as shown in Figure P28.73. Imagine the six straight lines in Figure P28.73 are each 10.0- resistors, with junctions at the four vertices. A 12.0-V battery is connected to any two of the vertices. Find (a) the equivalent resistance of the tetrahedron between these vertices and (b) the current in the batten.arrow_forwardThe current I is measured through a sample of an ohmic material as a voltage V is applied, (a) What is the current when the voltage is doubled to 2V (assume the change in temperature of the material is negligible)? (b) What is the voltage applied is the current measured is 0.27 (assume the change in temperature of the material is negligible)? What will happen to the current if the material if the voltage remains constant, but the temperature of the material increases significantly?arrow_forwardUnreasonable Results (a) To what temperature must you raise a resistor made of constantan to double its resistance, assuming a constant temperature coefficient of resistivity? (b) To cut it in half? (c) What is unreasonable about these results? (d) Which assumptions are unreasonable, or which premises are inconsistent?arrow_forward
- An iron wire is used to determine the melting point of material X. The resistance of the iron wire is 3.5 N at 30°C and increases to 5.5 N as material X starts to melt. What is the melting point of material X? [The temperature coefficient of resistivity for iron is 6.4 × 10-3 /C°] a. 157°C b. 119°C c. 100°C d. 27°Carrow_forward1. Silver is composed of 5.8 x 1028 free electrons per cubic meter. If a silver wire with a diameter of 1.8 mm can allow charges of 360 C to flow in 1 hour,a. What is the current in the conducting wire?b. What is the magnitude of the drift velocity of the electrons in the conducting wire?arrow_forwardA rod of length 2.3 m, with a rectangular cross section (1.5mm x 3.0 mm) is made ofa material with a resistivity of 6.1 × 10^-8 Ohm. A potential difference of 5.0 V isplaces across the ends of the rod.a. Draw a clear physics diagram of the problem.b. At what initial rate is heat generated in the rod?c. Will the rate from part (b) increase, decrease, or remain constantover time, as the rod remains connected to the 2.5 V potential difference?Explain brieflyarrow_forward
- Two pieces of copper wire have the same length, but wire A has square cross section of side s, whereas wire B has circular cross section of diameter s. Which of the following is TRUE? A. The resistivity of both wires is the same B. The resistance of both wires is the same C. The resistance of wire A is greater than B D. The resistance of wire B is greater than Aarrow_forward4. One technique for removing warts is to run an electrical current through them. The patient sits on a large, metal plate (called a “butt plate") and a metal needle connected to a power supply is touched to the wart. A current runs through the wart, heating it until it is removed. a. A large amount of energy needs to be delivered quickly. The resistance of human tissue is also large but the current is usually kept small. Given these facts, what can you predict about the voltage that is used? Why? b. Why does the patient need to sit on the butt plate (rather than on the plastic examining table)? c. Why (electrically) does the butt plate need to be large? d. How, if at all, will you need to change the voltage if you are removing a wart from someone's foot compared to removing one from the side of their hip? Why do you think so? You need to keep the amount of energy the same. e. Suppose you are removing a wart from a patient's lower leg. This patient has a metal rod running the length of…arrow_forwardShown below is a copper wire with the following characteristics: Diameter: 1.45 mm.00145m 1.45 × 10-8 m Number density of electrons: 8.47 x 1028 electrons/m³. Conductivity: 5.96 x 107 S/m a. Calculate the drift velocity (magnitude and direction) of the electrons in the wire when a current of 5.00 A is running through it. b. What direction is the current moving? c. Remembering that current density is a vector, calculate the magnitude and direction of the current density of this wire. d. Calculate the resistivity of the wire. e. Calculate the resistance of this wire if it were 10.0 m in length.arrow_forward
- Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage LearningPrinciples of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
- Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning