Bundle: Refrigeration And Air Conditioning Technology, 8th + Lab Manual + Lms Integrated For Mindtap Hvac-r, 4 Terms (24 Months) Printed Access Card
8th Edition
ISBN: 9781337087315
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
thumb_up100%
Chapter 24, Problem 1RQ
Which is not a pressure or force acting on a TXV diaphragm?
A. Head pressure
B. Evaporator pressure
C. Spring pressure
D. Bulb pressure
Expert Solution & Answer
To determine
The type of pressure or force that does not act on a TXV diaphragm.
Answer to Problem 1RQ
The type of pressure or force that does not act on a TXV diaphragm is Head Pressure.
Explanation of Solution
TXV is a thermostatic expansion valve. It is a component which is used in a refrigeration and air conditioning cycle. It is used for the expansion of refrigerant from the condenser pressure to the evaporator pressure. It controls the amount of refrigerant that which has to be fed from condenser to evaporator. Thermal sensors are installed in this type of expansion device, which maintains a constant superheat in the evaporator.
TXV expansion valve consists of a valve body, a diaphragm, spring, needle and seat, and different types of sensors. The diaphragm which is used in this expansion valve measures the evaporator pressure. The seat in the valve body of a TXV valve is stationary. The needle has an ability to move in the diaphragm. The pressure caused by the bulb acts on the diaphragm and from the other side, its pressure is applied by the evaporator and the spring. The diaphragm moves up and down due to these pressures applied by the different components of TXV. These pressure forces regulate the valve needle at a regular time to open and close.
Therefore, Evaporator pressure, Bulb pressure, and Spring pressure are the active forces which work to move the needle in a TXV diaphragm.
Conclusion:
The pressure or force that does not act on a TXV diaphragm is Head Pressure.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
It is required to treat 130 kmol/hr of chloroform-air feed gas mixture that contains
12% chloroform. It is required to remove 93% of chloroform using 150 kmol/hr of
solvent that contains 99.6% water and 0.4% chloroform. The cross sectional area of the
column is 0.8 m². Calculate the column height using the following data; kx'.a = 1.35
(kmol/m³.s (Ax)), and ky'.a = 0.06 (kmol/m³.s (Ay)), kx/ky = 1.35, and the equilibrium
data are:
X 0 0.0133 0.033
y 0 0.01 0.0266
0.049 0.064 0.0747 0.0933 0.1053
0.0433 0.06 0.0733
0.111
0.1
0.12
0.14
४
B:
Find the numerical solution for the 2D equation below and calculate the temperature values for
each grid point shown in Fig. 2 (show all steps).
(Do only one trail using following initial values and show the final matrix)
[T1]
T₂
T3
[T] 1
=
[0]
0
0
d
dx
dx)
(ka)+4(ka)
=
dy
-20xy, k = 1 + 0.3 T
ge
L=3cm, 4x= Ay
B.Cs.:
at x=0=LT=0°C
at y=0-L T=10°C
Fig. (2)
: +0
العنوان
use only
Two rods fins) having same dimensions, one made orass (k = 85 Wm
K) and the mer of copper (k = 375 W/m K), having of their ends inserted
into a furna. At a section 10.5 cm a way from furnace, the temperature of
brass rod 120 Find the distance at which the ame temperature would be
reached in the per rod ? both ends are ex osed to the same environment.
ns
2.05
۲/۱
ostrar
Chapter 24 Solutions
Bundle: Refrigeration And Air Conditioning Technology, 8th + Lab Manual + Lms Integrated For Mindtap Hvac-r, 4 Terms (24 Months) Printed Access Card
Ch. 24 - Which is not a pressure or force acting on a TXV...Ch. 24 - The needle and seat of a TXV are normally made of...Ch. 24 - The TXV tries to maintain a constant _____in...Ch. 24 - The four types of charges that the TXV uses to...Ch. 24 - Prob. 5RQCh. 24 - When do some TXVs require an external an external...Ch. 24 - Draw a diagram showing how an external equalizer...Ch. 24 - The TXV responds to an increased heat load by A....Ch. 24 - The three factors that determine the capacity of a...Ch. 24 - Explain why the entering liquid pressure has no...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- For the beam show below, draw A.F.D, S.F.D, B.M.D 6 kN/m 1 M B. 3 M Marrow_forward1. Two long rods of the same diameter-one made of brass (k=85w/m.k) and the other made of copper (k=375 w/m.k) have one of their ends inserted into a furnace (as shown in the following figure). Both rods are exposed to the same environment. At a distance of 105 mm from the furnace, the temperature of the brass rod is 120°C. At what distance from the furnace will the same temperature be reached in the copper rod? Furnace 105 mm T₁ Brass rod ⑪ h Too- x2- Ti Copper rodarrow_forward: +0 العنوان use only Two rods fins) having same dimensions, one made orass (k = 85 Wm K) and the mer of copper (k = 375 W/m K), having of their ends inserted into a furna. At a section 10.5 cm a way from furnace, the temperature of brass rod 120 Find the distance at which the ame temperature would be reached in the per rod ? both ends are ex osed to the same environment. ns 2.05 ۲/۱ ostrararrow_forward
- مشر on ۲/۱ Two rods (fins) having same dimensions, one made of brass(k=85 m K) and the other of copper (k = 375 W/m K), having one of their ends inserted into a furnace. At a section 10.5 cm a way from the furnace, the temperature brass rod 120°C. Find the distance at which the same temperature would be reached in the copper rod ? both ends are exposed to the same environment. 22.05 ofthearrow_forwardThe composite wall of oven with A= 1m² as in Fig.1 consists of three materials, two of with kA = 20 W/m K and kc = 50 W/m K with thickness, LA=0.3 m, L= 0.15 m and Lc 0.15 m. The inner surface temperature T1=900 K and the outer surface temperature T4 300 K, and an oven air temperature of To=1100 K, h=25 W/m². K. Determine kɛ and the temperatures T2 and T3 also draw the thermal resistance networkarrow_forwardTwo rods (fins) having same dimensions, one made of brass (k = 85 Wm K) and the other of copper (k = 375 W/m K), having one of their ends inserted into a furnace. At a section 10.5 cm a way from the furnace, the temperature of brass rod 120°C. Find the distance at which the same temperature would be reached in the copper rod ? both ends are exposed to the same environment. Ans 22.05arrow_forward
- A long wire (k-8 W/m °C.) with ro 5 mm and surface temperature Ts=180°C as shown in Fig.2. Heat is generated in the wire uniformly at a rate of 5 x107 W/m³. If the energy equation is given by: d 11(77) + - =0 k r dr dr Derive an expression for T(r) and determine the temperature at the center of the wire and at r=2 mm. Air Th T KA LA T2 T3 T Fig.1 KB kc 180°C Го Fig.2arrow_forwardB: Find the numerical solution for the 2D equation below and calculate the temperature values for each grid point shown in Fig. 2 (show all steps). (Do only one trail using following initial values and show the final matrix) T₂ 0 T3 0 I need a real solution, not artificial intelligence locarrow_forwardCan I solve this problem by calculating the initial kinetic energy with respect to G instead of A.arrow_forward
- B: Find the numerical solution for the 2D equation below and calculate the temperature values for each grid point shown in Fig. 2 (show all steps). (Do only one trail using following initial values and show the final matrix) T₂ 0 T3 0 locarrow_forwardShow all work. Indicate the origin that is used for each plane. Identify the Miller indices for the following planes. N 23 1 A) X B) yarrow_forwardthe following table gives weight gain time data for the oxidation of some metal at an elevated temperature W(mg/cm2). Time (min) 4.66 20 11.7 50 41.1 175 a) determin whether the oxidation kinetics obey a linear, parabolic, or logarithmic rate expression. b) Now compute W after a time of 1000 minarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Mechanical SPRING DESIGN Strategy and Restrictions in Under 15 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=dsWQrzfQt3s;License: Standard Youtube License