Study Guide with Lab Manual for Jeffus' Welding: Principles and Applications, 8th
8th Edition
ISBN: 9781305494701
Author: Larry Jeffus
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 22, Problem 26R
What dimensions can be given for a plug weld?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
An AISI 1018 steel ball with 1.100-in diameter is used as a roller between a flat plate
made from 2024 T3 aluminum and a flat table surface made from ASTM No. 30 gray
cast iron. Determine the maximum amount of weight that can be stacked on the
aluminum plate without exceeding a maximum shear stress of 19.00 kpsi in any of the
three pieces. Assume the figure given below, which is based on a typical Poisson's
ratio of 0.3, is applicable to estimate the depth at which the maximum shear stress
occurs for these materials.
1.0
0.8
Ratio of stress to Pmax
0.4
90
0.6
στ
Tmax
0.2
0.5a
a
1.5a
2a
2.5a
За
Distance from contact surface
The maximum amount of weight that can be stacked on the aluminum plate is
lbf.
A carbon steel ball with 27.00-mm diameter is pressed together with an aluminum ball
with a 36.00-mm diameter by a force of 11.00 N. Determine the maximum shear
stress and the depth at which it will occur for the aluminum ball. Assume the figure
given below, which is based on a typical Poisson's ratio of 0.3, is applicable to estimate
the depth at which the maximum shear stress occurs for these materials.
1.0
0.8
Ratio of stress to Pma
9 0.6
στ
24
0.4
Tmax
0.2
0
0.5a
a
1.5a
Z
2a
2.5a
За
Distance from contact surface
The maximum shear stress is determined to be
MPa.
The depth in the aluminum ball at which the maximum shear stress will occur is
determined to be [
mm.
Show all work please
Chapter 22 Solutions
Study Guide with Lab Manual for Jeffus' Welding: Principles and Applications, 8th
Ch. 22 - List the five joint types used in welding.Ch. 22 - What stresses must a welded joint withstand?Ch. 22 - Sketch and label five edge preparations used for...Ch. 22 - Sketch a V-grooved butt joint, and label all of...Ch. 22 - Sketch a weld on plates in the 1G and 1F...Ch. 22 - Sketch a weld on plates in the 2G and 2F...Ch. 22 - Sketch a weld on plates in the 4G and 4F...Ch. 22 - Sketch a weld on plates in the 4G and 4F...Ch. 22 - Sketch a weld on a pipe in the 1G position.Ch. 22 - Sketch a weld on a pipe in the 5G position.
Ch. 22 - Sketch a weld on a pipe in the 2G position.Ch. 22 - Sketch a weld on a pipe in the 6G position.Ch. 22 - Sketch a weld on a pipe in the 6GR position.Ch. 22 - Why are some joints back gouged?Ch. 22 - Why is it usually better to make a weld in the...Ch. 22 - What is a prequalified joint?Ch. 22 - Why is cost a consideration in joint design?Ch. 22 - Why are welding symbols used?Ch. 22 - What types of information can be included on a...Ch. 22 - Why is a tail added to the basic welding symbol?Ch. 22 - What types of information may appear on the...Ch. 22 - What are the different classifications of welds...Ch. 22 - How is the reference line always drawn?Ch. 22 - What is meant if the weld symbol is placed below...Ch. 22 - How are the dimensions for a fillet weld given?Ch. 22 - What dimensions can be given for a plug weld?Ch. 22 - What two units are used to show the minimum shear...Ch. 22 - How is the strength of a seam weld specified?Ch. 22 - How can the groove be cut on the edge of a plate?Ch. 22 - Sketch and dimension a V-groove weld symbol for a...Ch. 22 - How is the removal of the backing strip noted on a...Ch. 22 - How are flanged edges formed?Ch. 22 - Sketch two NDT symbols illustrating different...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Draw top, side, front view With pen(cil) and paper Multi view drawing and handwriting all of itarrow_forwardA wheel of diameter 150.0 mm and width 37.00 mm carrying a load 2.200 kN rolls on a flat rail. Take the wheel material as steel and the rail material as cast iron. Assume the figure given, which is based on a Poisson's ratio of 0.3, is applicable to estimate the depth at which the maximum shear stress occurs for these materials. At this critical depth, calculate the Hertzian stresses σr, σy, σz, and Tmax for the wheel. 1.0 0.8 0, т Ratio of stress to Pmax 0.4 0.6 90 69 0.2 0.5b b 1.5b Tmax 2b Distance from contact surface The Hertizian stresses are as follows: 02 = or = -23.8 psi for the wheel =| necessary.) σy for the wheel =| MPa σz for the wheel = MPa V4 for the wheel = | MPa 2.5b ཡི 3b MPa (Include a minus sign ifarrow_forwardOnly question 3arrow_forward
- In cold isostatic pressing, the mold is most typically made of which one of the following: thermosetting polymer tool steel sheet metal textile rubberarrow_forwardThe coefficient of friction between the part and the tool in cold working tends to be: lower higher no different relative to its value in hot workingarrow_forwardThe force F={25i−45j+15k}F={25i−45j+15k} lblb acts at the end A of the pipe assembly shown in (Figure 1). Determine the magnitude of the component F1 which acts along the member AB. Determine the magnitude of the component F2 which acts perpendicular to the AB.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Differences between Temporary Joining and Permanent Joining.; Author: Academic Gain Tutorials;https://www.youtube.com/watch?v=PTr8QZhgXyg;License: Standard Youtube License