Electric Motor Control
10th Edition
ISBN: 9781133702818
Author: Herman
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 22, Problem 1SQ
Describe what is meant by sequence control.
Expert Solution & Answer
To determine
Describe the meaning of sequence control.
Explanation of Solution
Sequence control:
Sequence control is a method of control to activate all the elements in a sequence manner.
This type of control is necessary wherever the activation of an auxiliary component depends on the main components.
In this control method, the starters are connected in a system such that one motor cannot be energized until another one is in operation.
Applications:
- Using in the systems wherever auxiliary equipment is associated with main systems. For example: hydraulic and lubricating oil pumps.
- Using in conveyor systems (subassembly or main line).
Conclusion:
Thus, the meaning of sequence control has been explained.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Instruction's:
Q2 02: Required Handwritten Answer with explanation , Dont send Ai Answers , Straight Forward will be Reported to team & a detailed review will be done against that tutor for wasting the students time.
Instruction's:
Q4 1: Required Handwritten Answer with explanation , Dont send Ai Answers , Straight Forward will be Reported to team & a detailed review will be done against that tutor for wasting the students time.
Instruction's:
Q2: Required Handwritten Answer with explanation , Dont send Ai Answers , Straight Forward will be Reported to team & a detailed review will be done against that tutor for wasting the students time.
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Instruction's: Q3 01: Required Handwritten Answer with explanation , Dont send Ai Answers , Straight Forward will be Reported to team & a detailed review will be done against that tutor for wasting the students time.arrow_forwardDon't use ai to answer I will report you answerarrow_forwardA periodic signal whose period is given by x(t) = Δ(t/τ), where τ = 1/20. The signal x(t) is band-limited by an ideal analog low-pass filter with a cutoff frequency fc. The signal x(t), ideally sampled at a rate of 80 Hz, is reconstructed using an ideal low-pass filter with a cutoff frequency of 40 Hz, resulting in the signal y(t). a) Plot the spectrum of y(t) if fc = 40 Hzb) Plot the spectrum of y(t) if fc = 20 Hzarrow_forward
- Q1 Q2 03 Find the total steel reinforcement (As) and the number of 20 mm bars that must be spread along the long direction of rectangular concrete footing of width B-2.10m which supports concrete column dimensions (0.4x 0.4) m. Given: D.L-900kN, L.L-800KN, qall-185kN/m², fc-21MPa, fy-400MPa. 300 450 Answer the following: A-Compare between the plate load test and standard penetration test, B-Define the disturbed samples, C- Find the depth of borehole for this case. B-2m. Dr=1.5m and qs =18ton/ m². The SPT records Versus depth are given in table below. Find qan for the raft foundation with B x B=10x10m and Df=2m, the allowable settlement is 50mm. 95 13 18 25arrow_forwardProject Statement A. It is required to introduce an additional load to cause maximum power transfer from the circuit below at the terminals a and b. The parallel loads resistances already connected are 50 Ω, 40 Ω, 30 Ω, 20 Ω, 10 Ω. 10 A 30022 w 8 Ω 5.2 Ω w w a + 500 V 12 Ω B. The circuit below is connected for long time to the terminal a and b of the circuit above after witch the switch is disconnected to allow the inductance system to discharge its stored energy. Determine the discharge current each τ and for 20 t and plot the current discharge behaviour. a 7 H 100 Ω 8 H 6H 10 H b C. Modify the 100 2 resistor or the inductor setup or both resistor and inductor setup to force the discharge current to be at least three times slower than in case B during the discharge. Your report must show the design steps and calculation then the relevant plots.arrow_forwardDraw the spectrum at the intermediate points and at the output of the cascaded systems. The input is x(t) = 6sinc(6t). The sampler operates at S = 12 Hz and performs ideal sampling. The cutoff frequency of the ideal low-pass filter is 5 Hz. X(t) → Sampler → Ideal Low-Pass Filter → Y(t)arrow_forward
- The signal x(t) is band-limited to 40 Hz and is modulated with a 320 Hz carrier, which generates y(t). This signal is then processed by a quadratic-law device that produces the output g(t) = y²(t). a) What is the minimum sampling rate for x(t) that avoids aliasing?b) What is the minimum sampling rate for y(t) that avoids aliasing?c) What is the minimum sampling rate for g(t) that avoids aliasing?arrow_forward1) Applying the bit mask to toggle the bits in positions 0 through 3 of the register AL, while passing through the bits in positions 7 through 4.What is the binary value of the AL after performing the following two instructions?MOV AL, 10111011 B;XOR AL, mask;arrow_forwardNeed a soluarrow_forward
- According to the book the answers are (а) 2.98 × 10-9 (b) 1.49 × 10-9arrow_forwardInstruction's: Q1: Required Handwritten Answer with explanation , Dont send Ai Answers , Straight Forward will be Reported to team & a detailed review will be done against that tutor for wasting the students time.arrow_forwardDon't use ai to answer I will report you answerarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Lead and lag compensation using Bode diagrams; Author: John Rossiter;https://www.youtube.com/watch?v=UBE-Tp173vk;License: Standard Youtube License