
(a)
The magnitude of impedance of the circuit.
(a)

Answer to Problem 95P
The impedance of the circuit is
Explanation of Solution
Write the expression to calculate the impedance of the circuit.
Write the expression to calculate
Here, f is the frequency.
Rewrite the equation for Z using the above equation.
Conclusion:
Substitute
(b)
The magnitude of rms value of current.
(b)

Answer to Problem 95P
The rms value of current is
Explanation of Solution
Write the expression to calculate the rms current.
Here,
Conclusion:
Substitute
(c)
The magnitude of phase angle.
(c)

Answer to Problem 95P
The phase angle is
Explanation of Solution
Write the expression to calculate the phase angle.
Here,
Conclusion:
Substitute
Since the inductive reactance is less than capacitive reactance, the phase angle is negative. Thus, the phase angle is
(d)
Whether the current lead or lag the voltage.
(d)

Answer to Problem 95P
The rms value of current is
Explanation of Solution
Write the expression to calculate the ratio of capacitive reactance to the inductive reactance.
Here, r is the ratio.
Rewrite the above expression using the expression for
Substitute
Since the ratio is greater than 1, the value of capacitive reactance is greater than the inductive reactance. Thus, the current leads the voltage.
Conclusion:
(e)
The magnitude of rms voltages across the elements.
(e)

Answer to Problem 95P
The rms voltage across the resistor, inductor and capacitor is respectively
Explanation of Solution
Write the expression to calculate the voltage across the resistor.
Here,
Substitute
Write the expression to calculate the voltage across the inductor.
Here,
Rewrite the above equation using the expression for
Substitute
Write the expression to calculate the voltage across the capacitor.
Rewrite the above equation using the expression for
Here,
Substitute
Conclusion:
Therefore, the rms voltage across the resistor, inductor and capacitor is respectively
Want to see more full solutions like this?
Chapter 21 Solutions
Physics
- Part A: kg (a) Water at 20 °C (p = 998.3 and v = 1 × 10-6 m²/s) flows through a galvanised m³ iron pipe (k = 0.15 mm) with a diameter of 25 mm, entering the room at point A and discharging at point C from the fully opened gate valve B at a volumetric flow rate of 0.003 m³/s. Determine the required pressure at A, considering all the losses that occur in the system described in Figure Q1. Loss coefficients for pipe fittings have been provided in Table 1. [25 marks] (b) Due to corrosion within the pipe, the average flow velocity at C is observed to be V2 m/s after 10 years of operation whilst the pressure at A remains the same as determined in (a). Determine the average annual rate of growth of k within the pipe. [15 marks] 4₁ Figure Q1. Pipe system Page 2 25 mmarrow_forwardFor an independent study project, you design an experiment to measure the speed of light. You propose to bounce laser light off a mirror that is 53.5 km due east and have it detected by a light sensor that is 119 m due south of the laser. The first problem is to orient the mirror so that the laser light reflects off the mirror and into the light sensor. (a) Determine the angle that the normal to the mirror should make with respect to due west.(b) Since you can read your protractor only so accurately, the mirror is slightly misaligned and the actual angle between the normal to the mirror and due west exceeds the desired amount by 0.003°. Determine how far south you need to move the light sensor in order to detect the reflected laser light.arrow_forwardA mirror hangs 1.67 m above the floor on a vertical wall. A ray of sunlight, reflected off the mirror, forms a spot on the floor 1.41 m from the wall. Later in the day, the spot has moved to a point 2.50 m from the wall. (a) What is the change in the angle of elevation of the Sun, between the two observations?arrow_forward
- It is not (theta 1i) or (pi/2 - theta 2i)arrow_forwardAssume the helium-neon lasers commonly used in student physics laboratories have power outputs of 0.250 mW. (a) If such a laser beam is projected onto a circular spot 3.40 mm in diameter, what is its intensity (in watts per meter squared)? 27.5 W/m² (b) Find the peak magnetic field strength (in teslas). 8.57e-7 X T (c) Find the peak electric field strength (in volts per meter). 144 V/marrow_forwardIdentify the most likely substancearrow_forward
- College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningUniversity Physics (14th Edition)PhysicsISBN:9780133969290Author:Hugh D. Young, Roger A. FreedmanPublisher:PEARSONIntroduction To Quantum MechanicsPhysicsISBN:9781107189638Author:Griffiths, David J., Schroeter, Darrell F.Publisher:Cambridge University Press
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningLecture- Tutorials for Introductory AstronomyPhysicsISBN:9780321820464Author:Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina BrissendenPublisher:Addison-WesleyCollege Physics: A Strategic Approach (4th Editio...PhysicsISBN:9780134609034Author:Randall D. Knight (Professor Emeritus), Brian Jones, Stuart FieldPublisher:PEARSON





