The resistance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm 2 and resistivity 1.7 × 10 − 8 Ω ⋅ m . The wire is wound on a plastic tube with 780 turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Question

Want to see the full answer?

Answer 1

Question

Chapter 21, Problem 48P

(a)

To determine

The resistance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780 turns, having a diameter of 4.0 cm and a length of 10.0 cm.

(b)

To determine

The inductance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

(c)

To determine

The frequency of the alternating current at which the inductive reactance of the solenoid is equal to its resistance, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

Part A: kg (a) Water at 20 °C (p = 998.3 and v = 1 × 10-6 m²/s) flows through a galvanised m³ iron pipe (k = 0.15 mm) with a diameter of 25 mm, entering the room at point A and discharging at point C from the fully opened gate valve B at a volumetric flow rate of 0.003 m³/s. Determine the required pressure at A, considering all the losses that occur in the system described in Figure Q1. Loss coefficients for pipe fittings have been provided in Table 1. [25 marks] (b) Due to corrosion within the pipe, the average flow velocity at C is observed to be V2 m/s after 10 years of operation whilst the pressure at A remains the same as determined in (a). Determine the average annual rate of growth of k within the pipe. [15 marks] 4₁ Figure Q1. Pipe system Page 2 25 mm

For an independent study project, you design an experiment to measure the speed of light. You propose to bounce laser light off a mirror that is 53.5 km due east and have it detected by a light sensor that is 119 m due south of the laser. The first problem is to orient the mirror so that the laser light reflects off the mirror and into the light sensor. (a) Determine the angle that the normal to the mirror should make with respect to due west.(b) Since you can read your protractor only so accurately, the mirror is slightly misaligned and the actual angle between the normal to the mirror and due west exceeds the desired amount by 0.003°. Determine how far south you need to move the light sensor in order to detect the reflected laser light.

A mirror hangs 1.67 m above the floor on a vertical wall. A ray of sunlight, reflected off the mirror, forms a spot on the floor 1.41 m from the wall. Later in the day, the spot has moved to a point 2.50 m from the wall. (a) What is the change in the angle of elevation of the Sun, between the two observations?

Answer 2

Question

Chapter 21, Problem 48P

(a)

To determine

The resistance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780 turns, having a diameter of 4.0 cm and a length of 10.0 cm.

(b)

To determine

The inductance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

(c)

To determine

The frequency of the alternating current at which the inductive reactance of the solenoid is equal to its resistance, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 3

Question

Chapter 21, Problem 48P

(a)

To determine

The resistance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780 turns, having a diameter of 4.0 cm and a length of 10.0 cm.

(b)

To determine

The inductance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

(c)

To determine

The frequency of the alternating current at which the inductive reactance of the solenoid is equal to its resistance, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 4

Question

Chapter 21, Problem 48P

(a)

To determine

The resistance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780 turns, having a diameter of 4.0 cm and a length of 10.0 cm.

(b)

To determine

The inductance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

(c)

To determine

The frequency of the alternating current at which the inductive reactance of the solenoid is equal to its resistance, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 5

Chapter 21, Problem 48P

(a)

To determine

The resistance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780 turns, having a diameter of 4.0 cm and a length of 10.0 cm.

(b)

To determine

The inductance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

(c)

To determine

The frequency of the alternating current at which the inductive reactance of the solenoid is equal to its resistance, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Answer 6

Chapter 21, Problem 48P

(a)

To determine

The resistance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780 turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Answer 7

Chapter 21, Problem 48P

(a)

To determine

The resistance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780 turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Answer 8

(b)

To determine

The inductance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Answer 9

(b)

To determine

The inductance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Answer 10

(c)

To determine

The frequency of the alternating current at which the inductive reactance of the solenoid is equal to its resistance, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Answer 11

(c)

To determine

The frequency of the alternating current at which the inductive reactance of the solenoid is equal to its resistance, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Answer 12

Expert Solution & Answer

Answer 13

Expert Solution & Answer

Answer 14

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 15

Ch. 21 - Review Question 21.1 Your friend thinks that...Ch. 21 - Review Question 21.2 You have a bar magnet and a...Ch. 21 - Review Question 21.3 What difficulty would occur...Ch. 21 - Review Question 21.4 Why do we write the law of...Ch. 21 - Review Question 21.5 How does the law of...Ch. 21 - Review Question 21.6 A capacitor in an electric...Ch. 21 - Prob. 7RQ Ch. 21 - Review Question 21.8 Explain how (a) an electric...Ch. 21 - 1. In which of the experiments with a loop and a...Ch. 21 - If you move the coil in Figure Q21.2 toward the N...

The resistance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm 2 and resistivity 1.7 × 10 − 8 Ω ⋅ m . The wire is wound on a plastic tube with 780 turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Concept explainers

The resistance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780 turns, having a diameter of 4.0 cm and a length of 10.0 cm.

The inductance of the solenoid, if it is made from a 100 m copper wire with cross-sectional area 0.2 mm2 and resistivity 1.7×10−8Ω⋅m. The wire is wound on a plastic tube with 780-turns, having a diameter of 4.0 cm and a length of 10.0 cm.

Want to see the full answer?

Chapter 21 Solutions