(a)
The average temperature of the hot surface of the board when it is vertical.
(a)
Explanation of Solution
Given:
The length of the board
The width of the board
The temperature of the room
The heat dissipated by the board
The emissivity of the surface of the board
The film temperature
Calculation:
Calculate the surface temperature of board
Refer Table A-22 “Properties of air at 1 atm pressure”.
Obtain the following values of different properties corresponding film temperature
Calculate the volume expansion coefficient
Calculate the characteristics length
Calculate the Rayleigh number
Calculate the Nusselt number
Calculate the area of heat transfer
Calculate the heat transfer coefficient of convection
Calculate the rate of heat transfer
By use of trial and error approach the surface temperature obtained is
Thus, the average temperature of the hot surface of the board is
(b)
The average temperature of the hot surface of the board when it is horizontal and hot surface facing up.
(b)
Explanation of Solution
Calculation:
Calculate the characteristic length
Calculate the Rayleigh number
Calculate the Nusselt number
Calculate the heat transfer coefficient of convection
Calculate the rate of heat transfer
Thus, the average temperature of the hot surface of the board is
(c)
The average temperature of the hot surface of the board when it is horizontal and hot surface facing down.
(c)
Explanation of Solution
Calculation:
Calculate the characteristic length
Calculate the Rayleigh number
Calculate the Nusselt number
Calculate the heat transfer coefficient of convection
Calculate the rate of heat transfer
Thus, the average temperature of the hot surface of the board is
Want to see more full solutions like this?
Chapter 20 Solutions
Fundamentals of Thermal-Fluid Sciences
- Solve this problem and show all of the workarrow_forwardaversity of Baoyion aculty of Engineering-AIMusyab Automobile Eng. Dep. Year: 2022-2023, st Course, 1st Attempt Stage: 3rd Subject: Heat Transfer I Date: 2023\01\23- Monday Time: 3 Hours Q4: A thick slab of copper initially at a uniform temperature of 20°C is suddenly exposed to radiation at one surface such that the net heat flux is maintained at a constant value of 3×105 W/m². Using the explicit finite-difference techniques with a space increment of Ax = = 75 mm, determine the temperature at the irradiated surface and at an interior point that is 150 mm from the surface after 2 min have elapsed. Q5: (12.5 M) A) A steel bar 2.5 cm square and 7.5 cm long is initially at a temperature of 250°C. It is immersed in a tank of oil maintained at 30°C. The heat-transfer coefficient is 570 W/m². C. Calculate the temperature in the center of the bar after 3 min. B) Air at 90°C and atmospheric pressure flows over a horizontal flat plate at 60 m/s. The plate is 60 cm square and is maintained at a…arrow_forwardUniversity of Baby on Faculty of Engineering-AIMusyab Automobile Eng. Dep. Year: 2022-2023. 1 Course, 1" Attempt Stage 3 Subject Heat Transfer I Date: 2023 01 23- Monday Time: 3 Hours Notes: Q1: • • Answer four questions only Use Troles and Appendices A) A flat wall is exposed to an environmental temperature of 38°C. The wall is covered with a layer of insulation 2.5 cm thick whose thermal conductivity is 1.4 W/m. C, and the temperature of the wall on the inside of the insulation is 315°C. The wall loses heat to the environment by convection. Compute the value of the convection heat-transfer coefficient that must be maintained on the outer surface of the insulation to ensure that the outer-surface temperature does not exceed 41°C. B) A vertical square plate, 30 cm on a side, is maintained at 50°C and exposed to room air at 20°C. The surface emissivity is 0.8. Calculate the total heat lost by both sides of the plate. (12.5 M) Q2: An aluminum fin 1.5 mm thick is placed on a circular tube…arrow_forward
- Solve this and show all of the workarrow_forwardNeed helparrow_forwardY F1 α В X F2 You and your friends are planning to move the log. The log. needs to be moved straight in the x-axis direction and it takes a combined force of 2.9 kN. You (F1) are able to exert 610 N at a = 32°. What magnitude (F2) and direction (B) do you needs your friends to pull? Your friends had to pull at: magnitude in Newton, F2 = direction in degrees, ẞ = N degarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY