Electric Motor Control
10th Edition
ISBN: 9781133702818
Author: Herman
Publisher: CENGAGE L
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 2, Problem 7SQ
To determine
Choose the correct option that represents the achievement of an automatic operation for the manual starters.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
QUESTION 12
The proper way to determine the required over-current protection is to:
determine the FLA based on the nameplate.
Use the standard rule of thumb that the over-current protection shall be 7 to 10x the locked rotor amps.
determine the watts by converting the HP rating on the nameplate to watts.
to determine the FLC by looking up the value in the appropriate table(s) in the NEC as they relate to the horsepower of the motor.
A 5-hp 230-volt shunt motor takes 18 amp when operating at full-load. The shunt filed resistance is 115 ohms and the armature resistance is 0.25 ohms. Calculate the value of the starter resistor if the armature current is limited to 1.5 times the rated value of the starting instant. (Assume a 3-volts brush contact).
Choose the best
Chapter 2 Solutions
Electric Motor Control
Ch. 2 - If the contacts on a manual starter cannot be...Ch. 2 - If the handle of an installed motor starter is in...Ch. 2 - How may an automatic operation be achieved when a...Ch. 2 - What does the term trip-free mean as it relates to...Ch. 2 - Prob. 5SQCh. 2 - Prob. 6SQCh. 2 - Prob. 7SQCh. 2 - Prob. 8SQCh. 2 - Select the best answer for each of the following....Ch. 2 - Select the best answer for each of the following....
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A starting resistor will most likely be needed in a/ an A. line starter.B. reduced-voltage starter.C. full-voltage starter. D. across-the-line starter.arrow_forward6.a. When you're taking a PM motor apart you should exercise special care not to damage theA. end bells.B. commutator.C. permanent magnets.D. brush holders.6.b. A PM field servo motor may be equipped with a resolver that is used toA. excite the armature windings.B. create a voltage that increases with velocity.C. prevent the brushes from sparking.D. feed back position information.arrow_forwardI will be grateful thanks a lot. An automatic starter circuit is to be designed for a shunt motor rated at 20 hp, 240 V, and 75 A. The armature resistance of the motor is 0.12 W, and the shunt field resistance is 40 W. The motor is to start with no more than 250 percent of its rated armature current, and as soon as the current falls to rated value, a starting resistor stage is to be cut out. How many stages of starting resistance are needed, and how big should each one be?arrow_forward
- Q51 Which NEC table is used to determine the full-load current of a torque motor? Select one: A. NEC TABLE 430.6(B) B. NEC TABLE 430.7(B) C. NEC TABLE 430.24 D. NEC TABLE 430.22arrow_forwardDraw an electrical diagram for a Star Delta starter with a forward rotation and reverse rotation switch.arrow_forwardMark the correct statements about armature controlled DC motors given below. (You can select multiple statements) 口 A) The armature voltage and the output speed is directly coupled B) The armature voltage and the output torque is directly coupled 口 C) The armature current and the output speed is directly coupled D) The armature current and the output torque is directly coupledarrow_forward
- What is the necessity of 3point starter? What is starter ?arrow_forwardCan you please explain in details so I can understand even better. Topic: Electrical Machinesarrow_forward7- The increase of the DC voltage feeding the switched reluctance motor will increase: a- Its speed. b- Its torque. c- Its efficiency. 8- The increase of the DC voltage feeding the stepper motor will increase: a- Its slew range. b- Its efficiency c- Its reliability 9- The reluctance motor is used in applications in: a- Calm environment. b- Harsh environment. c- Polluted environment. 10- The stepper motor used in a- Position control application. b- High speed applications. c- Heavy duty applications.arrow_forward
- I want questions from 2 to 10 to be answered. Question 2 - 10. Thats (2 through 10)arrow_forwardQuestion 4 A 55 hp, 440 V, 400 rpm DC shunt motor draws 107 A when operating at rated conditions. The motor has an armature-circuit resistance of 100 m2 and a total field-circuit resistance of 55 2. Draw a schematic of the motor in the space below showing all known quantities (resistances, currents, voltages and load). Show only symbols for unknowns. Determine the following for rated operation What is the motor armature current? (a) 99 A (b) 102 A (c) 107 A (d) 110 A (e) 115 A (i) What is the CEMF developed in the armature? (a) 449.9 V (b) 440.0 V (c) 430.1 V (d) 429.3 V (e) 428.5 V (i) What is the total windings (copper) losses in the motor? (a) 4842.5 W (b) 4500.1 W (c) 3520 0 W (d) 1145 W (e) 980.1 Warrow_forwardDo fast pleasearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
