The rms value of
a.
b.
c.
d.
The rms value of the voltage function
Answer to Problem 2.1MCQ
The option (b) is correct, therms value of the voltage function
Explanation of Solution
Given:
The expression for voltage
Concept used:
Write the standard sinusoidal expression for voltage
Here,
Write the expression for rms value of voltage.
Here,
Calculation:
Compare equation (1) with given expression.
Substitute
The rms value of the voltage function
Conclusion:
Thus, option
Want to see more full solutions like this?
Chapter 2 Solutions
POWER SYSTEM ANALYSIS+DESIGN-EBK >I<
- For the system below: if == m₁ =m₂ = 1 kg. k₁ = k₂ =1 Nm1, b = 20 N/ms"; then: 1) Find the transfer function () f(s) 2) Check the stability by Routh criteria method.arrow_forwardIf you have T.F.C.L.= k then: s2+2 5+k • 1) Find the open loop G(s). 2) Determine Steady state error for (unit step, ramp input, and acceleration input) 3) If es = 0.2, for ramp input, then find k,wn, 8. 4) For values in (3), then find t,,,,t, and M.. 5) For values in (4), then plot transient response with these values.arrow_forwardQ2) A. A three phase half wave controlled rectifier shown in fig (1) with a delay angle a, the input voltages are specified as va=100 cos(wt), v = 100 cos(wt + 120°), vc = 100cos (wt-120°) 1) Draw the average output voltage for a = 0°,30° and 60°. 2) Draw the la, land i, for each a 3) Calculate the average output voltage for each a n Va Vs Th, * Thz D Th3 R لے E Loadarrow_forward
- I hope the solution is on paper and not by artificial intelligencearrow_forwardObtain the number of roots in the RHP of D(s)=s+s+ 6s+5s3 + 10 s2 +58 +5arrow_forwardFor circuit below, if L = 0.5H, R=10,C=2, then 1) Find the transfer function Vo(s) u(s) of circuit below. 2) if u = k(v(t)- v,(t)), for feedback is added, find the value of k if peak overshoot is 0.2. 3) if u=(v(t)- v,(t)), for feedback is added, find the value of k if ess 0.2 for ramp input. - 4) if u = (1) ((t) vo(t)). Check the stability with varying the value of k for characteristic equation. R Votarrow_forward
- The question was sent hours ago and you sent an unclear answer. I hope the solution is on the paper and clear.arrow_forwardThe control system, shown in Fig. below, is subjected to a unit ramp function, a) Determine the value of k and k, such that the system has an overshoot of 16.303% and a damped natural frequency of 3.4641 rad/sec. b) Calculate the rise time, peak time and settling time. c) Define the system type d) Calculate the steady-state error of that system R(s) K (x+2) K ((s)arrow_forwardI hope the solution is on the paper and cleararrow_forward
- I hope the solution is on the paper and cleararrow_forwardPlease solve by pen and paper correctly step by step. Do not use chatgpt Or any AI tool.arrow_forwardConsider the circuit shown below, Vac 0- H Vdc ли R1 R2 where R₁ = 2.2KQ, R₂ = 4.7KQ, C = 0.1uF, Vdc = +5V, and Vac = 3V peak f = 1KHz. • Use superposition to calculate the DC voltage at point X; VDC = • Use superposition to calculate the AC (peak) voltage at point X; VAC =arrow_forward
- Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning