Explanation Given information: The weight ( W ) of the flywheel is 85 lb. The period ( τ n ) of small oscillation is 1.26 sec. Assuming the acceleration due to gravity ( g ) is 32.2 ft/s 2 . Calculation: Show the position of the flywheel as in Figure (1). Calculate the mass ( m ) using the relation: m = W g Substitute 85 lb for W and 32.2 ft/s 2 for g . m = 85 32.2 = 2.6398 lb ⋅ s 2 / ft Calculate the radius ( r ) using the relation: r = d 2 Substitute 14 in . for d . r = 14 in . 2 = 7 in . × 1 ft 12 in . = 0.583 ft For position 1: Write the expression for kinetic energy ( T 1 ) : T 1 = 1 2 I 0 θ ˙ m 2 Write the expression for potential energy ( V 1 ) : V 1 = 0 For position 2. Write the expression displacement ( h ): h = r ( 1 − cos θ m ) ( ∵ ( 1 − cos θ m ) = 2 sin 2 θ m 2 ) = r ( 2 sin 2 θ m 2 ) Here, θ ˙ m is maximum angular velocity. For small oscillation sin θ ≈ θ . h = r θ m 2 2 Write the expression for kinetic energy ( T 2 ) : T 2 = 0 Write the expression for potential energy ( V 2 ) : V 2 = m g h Substitute r θ m 2 2 for h . V 2 = m g r θ m 2 2 Write the expression for maximum angular velocity ( θ ˙ m ) : θ ˙ m = ω n θ m Expression for conservation of energy: T 1 + V 1 = T 2 + V 2 Substitute 1 2 I 0 θ ˙ m 2 for T 1 , 0 for V 1 , 0 for T 2 , and m g r θ m 2 2 for V 2

Loose Leaf for Vector Mechanics for Engineers: Statics and Dynamics

12th Edition

ISBN: 9781259977206

Author: BEER, Ferdinand P., Johnston Jr., E. Russell, Mazurek, David, Cornwell, Phillip J., SELF, Brian

Publisher: McGraw-Hill Education

See similar textbooks

Concept explainers

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaf…

Videos

Question

Chapter 19.3, Problem 19.73P

To determine

The centroidal moment of inertia (I¯) of the flywheel.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 19.3, Problem 19.72P

Chapter 19.3, Problem 19.74P

Students have asked these similar questions

Complete the following problems. Show your work/calculations, save as.pdf and upload to the assignment in Blackboard. 1. What are the x and y dimensions for the center position of holes 1,2, and 3 in the part shown in Figure 26.2 (below)? 6.0000 7118 Zero reference point 1.0005 1.0000 1.252 Bore C' bore 1.250 6.0000 .7118 0.2180 deep (3 holes) 2.6563 1.9445 3.000 diam. slot 0.3000 deep. 0.3000 wide 2.6563 1.9445

Complete the following problems. Show your work/calculations, save as.pdf and upload to the assignment in Blackboard. missing information to present a completed program. (Hint: You may have to look up geometry for the center drill and standard 0.5000 in twist drill to know the required depth to drill). 1. What are the x and y dimensions for the center position of holes 1,2, and 3 in the part shown in Figure 26.2 (below)? 6.0000 Zero reference point 7118 1.0005 1.0000 1.252 Bore 6.0000 .7118 Cbore 0.2180 deep (3 holes) 2.6563 1.9445 Figure 26.2 026022 (8lot and Drill Part) (Setup Instructions--- (UNITS: Inches (WORKPIECE NAT'L SAE 1020 STEEL (Workpiece: 3.25 x 2.00 x0.75 in. Plate (PRZ Location 054: ' XY 0.0 - Upper Left of Fixture TOP OF PART 2-0 (Tool List ( T02 0.500 IN 4 FLUTE FLAT END MILL #4 CENTER DRILL Dashed line indicates- corner of original stock ( T04 T02 3.000 diam. slot 0.3000 deep. 0.3000 wide Intended toolpath-tangent- arc entry and exit sized to programmer's judgment…

A program to make the part depicted in Figure 26.A has been created, presented in figure 26.B, but some information still needs to be filled in. Compute the tool locations, depths, and other missing information to present a completed program. (Hint: You may have to look up geometry for the center drill and standard 0.5000 in twist drill to know the required depth to drill).

Chapter 19 Solutions

Loose Leaf for Vector Mechanics for Engineers: Statics and Dynamics

Ch. 19.1 - A particle moves in simple harmonic motion....Ch. 19.1 - A particle moves in simple harmonic motion....Ch. 19.1 - Prob. 19.3P Ch. 19.1 - Prob. 19.4P Ch. 19.1 - Prob. 19.5P Ch. 19.1 - Prob. 19.6P Ch. 19.1 - Prob. 19.7P Ch. 19.1 - A simple pendulum consisting of a bob attached to...Ch. 19.1 - Prob. 19.9P Ch. 19.1 - Prob. 19.10P

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The centroidal moment of inertia ( I ¯ ) of the flywheel.

Solution Summary: The author calculates the centroidal moment of inertia of the flywheel using the relation: m=Wg.

Concept explainers

Videos

The centroidal moment of inertia (I¯) of the flywheel.

Want to see the full answer?

Chapter 19 Solutions