EP ENGR.MECH.:DYNAMICS-REV.MOD.MAS.ACC.
14th Edition
ISBN: 9780133976588
Author: HIBBELER
Publisher: PEARSON CO
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 19.2, Problem 9P
The disk has a weight of 10 lb and is pinned at its center O. If a vertical force of P = 2 lb is applied to the cord wrapped around its outer rim, determine the angular velocity of the disk in four seconds starting from rest Neglect the mass of the cord.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Continuity equation
A
y
x
dx
D
T
معادلة الاستمرارية
Ly
X
Q/Prove that
ди
хе
+ ♥+ ㅇ?
he
me
ze
ོ༞“༠ ?
Q
Derive (continuity equation)?
I want to derive clear mathematics.
motor supplies 200 kW at 6 Hz to flange A of the shaft shown in Figure. Gear B transfers 125 W of power to operating machinery in the factory, and the remaining power in the shaft is mansferred by gear D. Shafts (1) and (2) are solid aluminum (G = 28 GPa) shafts that have the same diameter and an allowable shear stress of t= 40 MPa. Shaft (3) is a solid steel (G = 80 GPa) shaft with an allowable shear stress of t = 55 MPa. Determine:
a) the minimum permissible diameter for aluminum shafts (1) and (2)
b) the minimum permissible diameter for steel shaft (3).
c) the rotation angle of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b).
Chapter 19 Solutions
EP ENGR.MECH.:DYNAMICS-REV.MOD.MAS.ACC.
Ch. 19.2 - Determine the angular momentum of the 100-kg disk...Ch. 19.2 - Determine the angular impulse about point O for t...Ch. 19.2 - If it is subjected to a couple moment of M = (3t2)...Ch. 19.2 - The 300-kg wheel has a rad1us of gyration about...Ch. 19.2 - If rod OA of negligible mass is subjected lo the...Ch. 19.2 - Gears A and B of mass 10 kg and 50 kg have radii...Ch. 19.2 - The 50-kg spool is subjected to a horizontal force...Ch. 19.2 - The reel has a weight of 150 lb and a radius of...Ch. 19.2 - The rigid body (slab) has a mass m and rotates...Ch. 19.2 - At a given Instant, the body has a linear momentum...
Ch. 19.2 - Show that if a slab is rotating about a fixed axis...Ch. 19.2 - The 40-kg disk is rotating at = 100 rad/s. When...Ch. 19.2 - The Impact wrench cons1sts of a slender 1-kg rod...Ch. 19.2 - The airplane is traveling in a straight line with...Ch. 19.2 - The double pulley consists of two wheels which are...Ch. 19.2 - The assembly weighs 10 lb and has a radius of...Ch. 19.2 - The disk has a weight of 10 lb and is pinned at...Ch. 19.2 - The 30-kg gear A has a radius of gyration about...Ch. 19.2 - Determine the angular velocity of the pulley when...Ch. 19.2 - The 40-kg roll of paper rests along the wall where...Ch. 19.2 - The slender rod has a mass m and is suspended at...Ch. 19.2 - The rod of length L and mass m lies on a smooth...Ch. 19.2 - A 4-kg disk A is mounted on arm BC. which has a...Ch. 19.2 - The frame of a tandem drum roller has a weight of...Ch. 19.2 - The 100-lb wheel has a radius of gyration of kG =...Ch. 19.2 - The 4-kg slender rod rests on a smooth floor If it...Ch. 19.2 - The double pulley consists of two wheels which are...Ch. 19.2 - The 100-kg spool is resting on the inclined...Ch. 19.2 - The spool has a weight of 30 lb and a radius of...Ch. 19.2 - The two gears A and B have weights and radii of...Ch. 19.2 - The hoop (thin ring) has a mass of 5 kg and is...Ch. 19.2 - The 30-kg gear is subjected to a force of P =...Ch. 19.2 - The 30-lb flywheel A has a radius of gyration...Ch. 19.2 - If the shaft is subjected to a torque of M = (...Ch. 19.2 - The double pulley consists of two wheels which are...Ch. 19.2 - The crate has a mass mc. Determine the constant...Ch. 19.4 - The turntable T of a record player has a mass of...Ch. 19.4 - The 10-g bullet having a velocity of 800 m/s is...Ch. 19.4 - The 10-g bullet having a velocity of 800 m/s is...Ch. 19.4 - The circular disk has a mass m and is suspended at...Ch. 19.4 - The 80-kg man is holding two dumbbells while...Ch. 19.4 - The platform swing consists of a 200-lb flat plate...Ch. 19.4 - The 2-kg rod ACB supports the two 4-kg disks at...Ch. 19.4 - The satellite has a mass of 200 kg and a radius of...Ch. 19.4 - Disk A has a weight of 20 lb. An inextensible...Ch. 19.4 - The plank has a weight of 30 lb, center of gravity...Ch. 19.4 - The 12-kg rod AB is pinned to the 40-kg disk. If...Ch. 19.4 - A thin rod of mass m has an angular velocity o...Ch. 19.4 - Tests of impact on the fixed crash dummy are...Ch. 19.4 - The vertical shaft is rotating with an angular...Ch. 19.4 - The mass center of the 3-lb ball h3s a velocity of...Ch. 19.4 - Prob. 44PCh. 19.4 - The 10-lb block is sliding on the smooth surface...Ch. 19.4 - Determine the height hat which a billiard ball of...Ch. 19.4 - The pendulum consists of a 15-kg solid ball and...Ch. 19.4 - The 4-lb rod AB is hanging in the vertical...Ch. 19.4 - Determine the largest angular velocity 1 the disk...Ch. 19.4 - The solid ball of mass m is dropped with a...Ch. 19.4 - The wheel has a mass of 50 kg and a radius of...Ch. 19.4 - The wheel has a mass of 50 kg and a radius of...Ch. 19.4 - The rod of mass m and length L is released from...Ch. 19.4 - Prob. 55PCh. 19.4 - A ball having a mass of 8 kg and initial speed of...Ch. 19.4 - A solid ball with a mass m is thrown on the ground...Ch. 19.4 - The pendulum consists of a 10-lb solid ball and...Ch. 19.4 - The cable is subjected to a force of P = (10t2)...Ch. 19.4 - The space capsule has a mass of 1200 kg and a...Ch. 19.4 - The tire has a mass of 9 kg and a rad1us of...Ch. 19.4 - The wheel having a mass of 100 kg and a radius of...Ch. 19.4 - The spool has a weight of 30 lb and a radius of...Ch. 19.4 - Spool B is at rest and spool A is rotating at 6...Ch. 19.4 - A thin disk of mass m has an angular velocity 1...Ch. 19.4 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- First monthly exam Gas dynamics Third stage Q1/Water at 15° C flow through a 300 mm diameter riveted steel pipe, E-3 mm with a head loss of 6 m in 300 m length. Determine the flow rate in pipe. Use moody chart. Q2/ Assume a car's exhaust system can be approximated as 14 ft long and 0.125 ft-diameter cast-iron pipe ( = 0.00085 ft) with the equivalent of (6) regular 90° flanged elbows (KL = 0.3) and a muffler. The muffler acts as a resistor with a loss coefficient of KL= 8.5. Determine the pressure at the beginning of the exhaust system (pl) if the flowrate is 0.10 cfs, and the exhaust has the same properties as air.(p = 1.74 × 10-3 slug/ft³, u= 4.7 x 10-7 lb.s/ft²) Use moody chart (1) MIDAS Kel=0.3 Q3/Liquid ammonia at -20°C is flowing through a 30 m long section of a 5 mm diameter copper tube(e = 1.5 × 10-6 m) at a rate of 0.15 kg/s. Determine the pressure drop and the head losses. .μ= 2.36 × 10-4 kg/m.s)p = 665.1 kg/m³arrow_forward2/Y Y+1 2Cp Q1/ Show that Cda Az x P1 mactual Cdf Af R/T₁ 2pf(P1-P2-zxgxpf) Q2/ A simple jet carburetor has to supply 5 Kg of air per minute. The air is at a pressure of 1.013 bar and a temperature of 27 °C. Calculate the throat diameter of the choke for air flow velocity of 90 m/sec. Take velocity coefficient to be 0.8. Assume isentropic flow and the flow to be compressible. Quiz/ Determine the air-fuel ratio supplied at 5000 m altitude by a carburetor which is adjusted to give an air-fuel ratio of 14:1 at sea level where air temperature is 27 °C and pressure is 1.013 bar. The temperature of air decreases with altitude as given by the expression The air pressure decreases with altitude as per relation h = 19200 log10 (1.013), where P is in bar. State any assumptions made. t = ts P 0.0065harrow_forward36 2) Use the method of MEMBERS to determine the true magnitude and direction of the forces in members1 and 2 of the frame shown below in Fig 3.2. 300lbs/ft member-1 member-2 30° Fig 3.2. https://brightspace.cuny.edu/d21/le/content/433117/viewContent/29873977/Viewarrow_forward
- Can you solve this for me?arrow_forward5670 mm The apartment in the ground floor of three floors building in Fig. in Baghdad city. The details of walls, roof, windows and door are shown. The window is a double glazing and air space thickness is 1.3cm Poorly Fitted-with Storm Sash with wood strip and storm window of 0.6 cm glass thickness. The thickness of door is 2.5 cm. The door is Poor Installation. There are two peoples in each room. The height of room is 280 cm. assume the indoor design conditions are 25°C DBT and 50 RH, and moisture content of 8 gw/kga. The moisture content of outdoor is 10.5 gw/kga. Calculate heat gain for living room : الشقة في الطابق الأرضي من مبنى ثلاثة طوابق في مدينة بغداد يظهر في مخطط الشقة تفاصيل الجدران والسقف والنوافذ والباب. النافذة عبارة عن زجاج مزدوج وسمك الفراغ الهوائي 1.3 سم ضعيف الاحكام مع ساتر حماية مع إطار خشبي والنافذة بسماكة زجاج 0.6 سم سماكة الباب 2.5 سم. الباب هو تركيب ضعيف هناك شخصان في كل غرفة. ارتفاع الغرفة 280 سم. افترض أن ظروف التصميم الداخلي هي DBT25 و R50 ، ومحتوى الرطوبة 8…arrow_forwardHow do i solve this problem?arrow_forward
- Q4/ A compressor is driven motor by mean of a flat belt of thickness 10 mm and a width of 250 mm. The motor pulley is 300 mm diameter and run at 900 rpm and the compressor pulley is 1500 mm diameter. The shaft center distance is 1.5 m. The angle of contact of the smaller pulley is 220° and on the larger pulley is 270°. The coefficient of friction between the belt and the small pulley is 0.3, and between the belt and the large pulley is 0.25. The maximum allowable belt stress is 2 MPa and the belt density is 970 kg/m³. (a) What is the power capacity of the drive and (b) If the small pulley replaced by V-grooved pulley of diameter 300 mm, grooved angle of 34° and the coefficient of friction between belt and grooved pulley is 0.35. What will be the power capacity in this case, assuming that the diameter of the large pulley remain the same of 1500 mm.arrow_forwardYou are tasked with designing a power drive system to transmit power between a motor and a conveyor belt in a manufacturing facility as illustrated in figure. The design must ensure efficient power transmission, reliability, and safety. Given the following specifications and constraints, design drive system for this application: Specifications: Motor Power: The electric motor provides 10 kW of power at 1,500 RPM. Output Speed: The output shaft should rotate at 150 rpm. Design Decisions: Transmission ratio: Determine the necessary drive ratio for the system. Shaft Diameter: Design the shafts for both the motor and the conveyor end. Material Selection: Choose appropriate materials for the gears, shafts. Bearings: Select suitable rolling element bearings. Constraints: Space Limitation: The available space for the gear drive system is limited to a 1-meter-long section. Attribute 4 of CEP Depth of knowledge required Fundamentals-based, first principles analytical approach…arrow_forward- | العنوان In non-continuous dieless drawing process for copper tube as shown in Fig. (1), take the following data: Do-20mm, to=3mm, D=12mm, ti/to=0.6 and v.-15mm/s. Calculate: (1) area reduction RA, (2) drawing velocity v. Knowing that: ti: final thickness V. Fig. (1) ofthrearrow_forward
- A direct extrusion operation produces the cross section shown in Fig. (2) from an aluminum billet whose diameter 160 mm and length - 700 mm. Determine the length of the extruded section at the end of the operation if the die angle -14° 60 X Fig. (2) Note: all dimensions in mm.arrow_forwardFor hot rolling processes, show that the average strain rate can be given as: = (1+5)√RdIn(+1)arrow_forward: +0 usão العنوان on to A vertical true centrifugal casting process is used to produce bushings that are 250 mm long and 200 mm in outside diameter. If the rotational speed during solidification is 500 rev/min, determine the inside radii at the top and bottom of the bushing if R-2R. Take: -9.81 mis ۲/۱ ostrararrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License