Concept explainers
A 5-kg collar C is released from rest in the position shown and slides without friction on a vertical rod until it hits a spring with a constant of k = 720 N/m that it compresses. The velocity of the collar is reduced to zero, and the collar reverses the direction of its motion and returns to its initial position. The cycle is then repeated. Determine (a) the period of the motion of the collar, (b) the velocity of the collar 0.4 s after it was released. (Note: This is a periodic motion, but it is not simple harmonic motion.)
Fig. P19.15
(a)
The period
Answer to Problem 19.15P
The period
Explanation of Solution
Given Information:
The mass (m) of the collar C is 5 kg.
The spring constant (k) is
The value of acceleration due to gravity (g) is
The vertical distance (h) between the collar and the spring is 0.5 m.
Calculation:
Calculate the natural circular frequency
Substitute
Calculate the initial velocity
Substitute
Calculate the free fall time
Substitute
Measure the displacement (x) from the position of static displacement of the spring.
Calculate the weight (W) of the collar C using the relation:
Substitute 5kg for m and
Calculate the static displacement
Substitute
Show the displacement of the collar and spring while impact as in Figure (1).
Write the equation of motion for simple harmonic motion as below:
Substitute 5 kg for m and
Write the expression for displacement (x):
Differentiate the above equation.
When time (t) is 0 the displacement (x) is equal to
Substitute 0 for t and
Rewrite the above equation,
Substitute 0 for t,
Calculate the phase angle
Substitute
Calculate the amplitude
Substitute
Hence, from time of impact, the ‘time of flight’ is the time necessary for the collar to come to rest on its downward motion. The time required for collar to rest return is
At time
Calculate the time
Substitute 0 for
Substitute
Calculate the period of motion
Substitute
Therefore, the period
(b)
The velocity
Answer to Problem 19.15P
The velocity
Explanation of Solution
Given Information:
The mass (m) of the collar C is 5 kg.
The spring constant (k) is
The value of acceleration due to gravity (g) is
The vertical distance (h) between the collar and the spring is 0.5 m.
Calculation:
Calculate the velocity
Rewrite equation (2).
Substitute
Therefore, the velocity
Want to see more full solutions like this?
Chapter 19 Solutions
VECTOR MECH...,STAT.+DYN.(LL)-W/ACCESS
- 2. A railroad car of mass 2,000 kg traveling at a velocity v = 10 m/s is stopped at the end of the tracks by a spring- damper system. If the stiffness of the spring is k =180 N/mm and the damping constant is c = 20 N-s/mm, determine (a) the maximum displacement of the car after engaging the springs and damper and (b) the time taken to reach the maximum displacement. k/2 k/2 A. 1.0048 m, 0.0736 s C. 1.1048 m, 1.0736 s B. 1.0548 m, 0.5736 s D. 1.1548 m, 1.5736 sarrow_forwardA5 lbf weight is suspended froma vertical spring having a stiffness k = 50 lbf/ft. An impressed force F = 0.25 sin 8t lbę where t is in seconds is acting on the weight. Determine the equation of motion of the weight when it is pulled down 3 inches from the equilibrium position and released from rest.arrow_forwardDetermine the natural frequency of the spring- mass system in both radians per second and cycles per seconds (Hz) k = 9.72 kN/m 30 kg Own wn = 2.86 rad/s and fn Own = 0.09 rad/s and fn Own = 0.57 rad/s and fn Own = 18 rad/s and fn =arrow_forward
- 1arrow_forward2. A body weighing 25 lb is suspended from a spring of constant k = 160 lb /ft. At time t = 0 it has a downward velocity of 2 ft /sec as it passes through the position of static equilibrium. Determine (a) the system period and (b) the maximum acceleration attained by the mass.arrow_forward33arrow_forward
- A 2.3-kg object is suspended using two linear springs (k1 = 45 N/m and k2 = 21 N/m), as shown below. Due to aerodynamic effects and other losses, you observe that the amplitude of the vibration is halved after 5 complete cycles. If the initial mass was displaced 270 millimetres below the equilibrium position (i.e. negative initial displacement) and then released from rest, determine the position of the mass after 11 seconds. Give your answer in millimetres rounded to one decimal place. Enter positive values if the mass is above the equilibrium position and negative values if it is below the equilibrium position. k karrow_forwardThe system shown below consists of a uniform disk D that has a mass of mp = 3.0 kg and a radius of r = 0.5 meters. The disk is connected by a massless cable to a block. The system is released from rest and the disk starts rolling without sliding with the angular acceleration of a = 24 rad in the clockwise direction. Determine the tension developed in the cable (in Newtons) at this instant. Consider 0 = 30° and g 10 * mparrow_forwardA spring with a spring constant of 1200lbf/ft is attached to block with a mass of 96.6lbm horizontally. It was initially displaced 3 inches to the left of the equilibrium position and released at 12in/s going to the right. Determine also the b) velocity 2 seconds after the push in ft/s *arrow_forward
- Find the magnitude and direction of the velocity at point B.arrow_forwardThe 10-kg bar is released from rest in the horizontal position 1 and falls to positions 2. The unstretched lengthy of the spring is 0.6 m and the spring constant is k=20 N/m .what will be the bar 's angular velocity when it is in position 2.arrow_forwardHi, I have an engineering dynamics question.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY