EBK FUNDAMENTALS OF THERMAL-FLUID SCIEN
5th Edition
ISBN: 9781259151323
Author: CENGEL
Publisher: MCGRAW HILL BOOK COMPANY
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 19, Problem 130RQ
(a)
To determine
The steady rate of heat transfer.
(b)
To determine
The length of the tubes.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A virtual experiment is designed to determine the effect of friction on the timing and speed
of packages being delivered to a conveyor belt and the normal force applied to the tube.
A package is held and then let go at the edge of a circular shaped tube of radius R = 5m.
The particle at the bottom will transfer to the conveyor belt, as shown below.
Run the simulations for μ = 0, 0.1, 0.2, 0.3, 0.4, 0.5, 0.6 and determine the time and speed at
which the package is delivered to the conveyor belt. In addition, determine the maximum
normal force and its location along the path as measured by angle 0.
Submit in hardcopy form:
(0) Free Body Diagram, equations underneath, derivations
(a) Your MATLAB mfile
(b) A table listing the values in 5 columns:
μ, T (time of transfer), V (speed of transfer), 0 (angle of max N), Nmax (max N)
(c) Based on your results, explain in one sentence what you think will happen to the
package if the friction is increased even further, e.g. μ = 0.8.
NOTE: The ODE is…
Patm = 1 bar
Piston
m = 50 kg
5 g of Air
T₁ = 600 K
P₁ = 3 bar
Stops
A 9.75 x 10-3 m²
FIGURE P3.88
Assume a Space Launch System (Figure 1(a)) that is approximated as a cantilever undamped single degree of freedom (SDOF) system with a mass at its free end (Figure 1(b)). The cantilever is assumed to be massless. Assume a wind load that is approximated with a concentrated harmonic forcing function p(t) = posin(ωt) acting on the mass. The known properties of the SDOF and the applied forcing function are given below. • Mass of SDOF: m =120 kip/g • Acceleration of gravity: g = 386 in/sec2 • Bending sectional stiffness of SDOF: EI = 1015 lbf×in2 • Height of SDOF: h = 2000 inches • Amplitude of forcing function: po = 6 kip • Forcing frequency: f = 8 H
Chapter 19 Solutions
EBK FUNDAMENTALS OF THERMAL-FLUID SCIEN
Ch. 19 - Prob. 1PCh. 19 - Prob. 2PCh. 19 - What is external forced convection? How does it...Ch. 19 - Prob. 4PCh. 19 - Consider a hot baked potato. Will the potato cool...Ch. 19 - What is the physical significance of the Nusselt...Ch. 19 - When is heat transfer through a fluid conduction...Ch. 19 - An average man has a body surface area of 1.8 m2...Ch. 19 - The convection heat transfer coefficient for a...Ch. 19 - Prob. 10P
Ch. 19 - The upper surface of a 50-cm-thick solid plate (k...Ch. 19 - Prob. 12PCh. 19 - During air cooling of oranges, grapefruit, and...Ch. 19 - During air cooling of steel balls, the convection...Ch. 19 - Prob. 15PCh. 19 - Water at 43.3°C flows over a large plate at a...Ch. 19 - Prob. 17PCh. 19 - Hot engine oil at 150°C is flowing in parallel...Ch. 19 - Prob. 19PCh. 19 - Prob. 22PCh. 19 - Prob. 23PCh. 19 - Prob. 24PCh. 19 - Prob. 25PCh. 19 - Prob. 27PCh. 19 - Prob. 28PCh. 19 - Prob. 30PCh. 19 - Prob. 31PCh. 19 - Solar radiation is incident on the glass cover of...Ch. 19 - Liquid mercury at 250°C is flowing with a velocity...Ch. 19 - Prob. 35PCh. 19 - Prob. 36PCh. 19 - Air is flowing in parallel over the upper surface...Ch. 19 - Prob. 40PCh. 19 - Consider laminar flow of air across a hot circular...Ch. 19 - Prob. 42PCh. 19 - A heated long cylindrical rod is placed in a cross...Ch. 19 - A person extends his uncovered arms into the windy...Ch. 19 - Prob. 46PCh. 19 - Prob. 47PCh. 19 - Prob. 49PCh. 19 - Consider a person who is trying to keep cool on a...Ch. 19 - A 12-ft-long, 1.5-kW electrical resistance wire is...Ch. 19 - Prob. 52PCh. 19 - Prob. 53PCh. 19 - Prob. 55PCh. 19 - Prob. 56PCh. 19 - A 10-cm-diameter, 30-cm-high cylindrical bottle...Ch. 19 - Prob. 58PCh. 19 - An incandescent lightbulb is an inexpensive but...Ch. 19 - Prob. 60PCh. 19 - Prob. 61PCh. 19 - Prob. 62PCh. 19 - A coated sheet is being dried with hot air blowing...Ch. 19 - Prob. 65PCh. 19 - Consider laminar forced convection in a circular...Ch. 19 - Consider turbulent forced convection in a circular...Ch. 19 - What does the logarithmic mean temperature...Ch. 19 - Prob. 69PCh. 19 - Prob. 70PCh. 19 - Prob. 71PCh. 19 - Prob. 72PCh. 19 - Prob. 73PCh. 19 - Cooling water available at 10°C is used to...Ch. 19 - Prob. 75PCh. 19 - Inside a condenser, there is a bank of seven...Ch. 19 - Prob. 79PCh. 19 - Prob. 81PCh. 19 - Prob. 82PCh. 19 - In a thermal system, water enters a 25-mm-diameter...Ch. 19 - Prob. 84PCh. 19 - Prob. 85PCh. 19 - Prob. 86PCh. 19 - Prob. 88PCh. 19 - Prob. 89PCh. 19 - Prob. 90PCh. 19 - Glycerin is being heated by flowing between two...Ch. 19 - Determine the convection heat transfer coefficient...Ch. 19 - Prob. 94PCh. 19 - Water is to be heated from 10°C to 80°C as it...Ch. 19 - Consider a fluid with a Prandtl number of 7...Ch. 19 - The hot water needs of a household are to be met...Ch. 19 - Prob. 98PCh. 19 - Prob. 99PCh. 19 - Hot air at atmospheric pressure and 85°C enters a...Ch. 19 - Prob. 102PCh. 19 - Prob. 104PCh. 19 - Prob. 105PCh. 19 - Prob. 106PCh. 19 - Prob. 107RQCh. 19 - Prob. 108RQCh. 19 - The passenger compartment of a minivan traveling...Ch. 19 - Prob. 110RQCh. 19 - Prob. 111RQCh. 19 - Prob. 112RQCh. 19 - Prob. 113RQCh. 19 - Prob. 114RQCh. 19 - Prob. 115RQCh. 19 - Prob. 116RQCh. 19 - Airstream at 1 atm flows, with a velocity of 15...Ch. 19 - Prob. 118RQCh. 19 - Prob. 119RQCh. 19 - Prob. 120RQCh. 19 - Prob. 121RQCh. 19 - A 3-m-internal-diameter spherical tank made of...Ch. 19 - Prob. 123RQCh. 19 - Prob. 124RQCh. 19 - Prob. 125RQCh. 19 - Prob. 126RQCh. 19 - Prob. 127RQCh. 19 - Prob. 128RQCh. 19 - Prob. 129RQCh. 19 - Prob. 130RQCh. 19 - Prob. 131RQCh. 19 - Prob. 132RQCh. 19 - Prob. 133RQCh. 19 - Prob. 134RQCh. 19 - Prob. 135RQCh. 19 - Prob. 136RQCh. 19 - Prob. 137RQCh. 19 - Prob. 138RQCh. 19 - Prob. 139RQCh. 19 - Prob. 140RQCh. 19 - Liquid water enters a 10-m-long smooth rectangular...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Assume a Space Launch System (Figure 1(a)) that is approximated as a cantilever undamped single degree of freedom (SDOF) system with a mass at its free end (Figure 1(b)). The cantilever is assumed to be massless. Assume a wind load that is approximated with a concentrated harmonic forcing function p(t) = posin(ωt) acting on the mass. The known properties of the SDOF and the applied forcing function are given below. • Mass of SDOF: m =120 kip/g • Acceleration of gravity: g = 386 in/sec2 • Bending sectional stiffness of SDOF: EI = 1015 lbf×in2 • Height of SDOF: h = 2000 inches • Amplitude of forcing function: po = 6 kip • Forcing frequency: f = 8 Hz Figure 1: Single-degree-of-freedom system in Problem 1. Please compute the following considering the steady-state response of the SDOF system. Do not consider the transient response unless it is explicitly stated in the question. (a) The natural circular frequency and the natural period of the SDOF. (10 points) (b) The maximum displacement of…arrow_forwardAssume a Space Launch System (Figure 1(a)) that is approximated as a cantilever undamped single degree of freedom (SDOF) system with a mass at its free end (Figure 1(b)). The cantilever is assumed to be massless. Assume a wind load that is approximated with a concentrated harmonic forcing function p(t) = posin(ωt) acting on the mass. The known properties of the SDOF and the applied forcing function are given below. • Mass of SDOF: m =120 kip/g • Acceleration of gravity: g = 386 in/sec2 • Bending sectional stiffness of SDOF: EI = 1015 lbf×in2 • Height of SDOF: h = 2000 inches • Amplitude of forcing function: po = 6 kip • Forcing frequency: f = 8 Hz Figure 1: Single-degree-of-freedom system in Problem 1. Please compute the following considering the steady-state response of the SDOF system. Do not consider the transient response unless it is explicitly stated in the question. (a) The natural circular frequency and the natural period of the SDOF. (10 points) (b) The maximum displacement of…arrow_forwardPlease solve 13 * √(2675.16)² + (63.72 + 2255,03)² = 175x106 can you explain the process for getting d seperate thank youarrow_forward
- If the 300-kg drum has a center of mass at point G, determine the horizontal and vertical components of force acting at pin A and the reactions on the smooth pads C and D. The grip at B on member DAB resists both horizontal and vertical components of force at the rim of the drum. P 60 mm; 60 mm: 600 mm A E 30° B C 390 mm 100 mm D Garrow_forwardThe design of the gear-and-shaft system shown requires that steel shafts of the same diameter be used for both AB and CD. It is further required that the angle D through which end D of shaft CD rotates not exceed 1.5°. Knowing that G = 77.2 GPa, determine the required diameter of the shafts. 40 mm 400 mm 100 mm 600 mm T-1000 N-m Darrow_forwardAssume a Space Launch System (Figure 1(a)) that is approximated as a cantilever undamped single degree of freedom (SDOF) system with a mass at its free end (Figure 1(b)). The cantilever is assumed to be massless. Assume a wind load that is approximated with a concentrated harmonic forcing function p(t) = posin(ωt) acting on the mass. The known properties of the SDOF and the applied forcing function are given below. • Mass of SDOF: m =120 kip/g • Acceleration of gravity: g = 386 in/sec2 • Bending sectional stiffness of SDOF: EI = 1015 lbf×in2 • Height of SDOF: h = 2000 inches • Amplitude of forcing function: po = 6 kip • Forcing frequency: f = 8 Hzarrow_forward
- 13.44 The end of a cylindrical liquid cryogenic propellant tank in free space is to be protected from external (solar) radiation by placing a thin metallic shield in front of the tank. Assume the view factor Fts between the tank and the shield is unity; all surfaces are diffuse and gray, and the surroundings are at 0 K. Tank T₁ Shield, T T₁ = 100 K E1 Solar irradiation Gs ε₁ = ε₂ = 0.05 ε₁ = 0.10 Gs = 1250 W/m² E2 Find the temperature of the shield T, and the heat flux (W/m²) to the end of the tank.arrow_forwardquestion 664 thank youarrow_forward13.38 Consider the attic of a home located in a hot climate. The floor of the attic is characterized by a width of L₁ = 8 m while the roof makes an angle of 0 = 30° from the horizontal direction, as shown in the schematic. The homeowner wishes to reduce the heat load to the home by adhering bright aluminum foil (ε = 0.07) onto the surfaces of the attic space. Prior to installation of the foil, the surfaces are of emissivity & = 0.90. Attic A2, 82, T2 0 = 30° A1, E1, T₁ 土 L₁ = 8 m (a) Consider installation on the bottom of the attic roof only. Determine the ratio of the radiation heat transfer after to before the installation of the foil. (b) Determine the ratio of the radiation heat transfer after to before installation if the foil is installed only on the top of the attic floor. (c) Determine the ratio of the radiation heat transfer if the foil is installed on both the roof bottom and the floor top.arrow_forward
- 13.1 Determine F2 and F2 for the following configura- tions using the reciprocity theorem and other basic shape factor relations. Do not use tables or charts. (a) Small sphere of area A, under a concentric hemi- sphere of area A₂ = 3A₁ A₂ A1 (a) (b) Long duct. Also, what is F₁₂? A₂ Αν (b) (c) Long inclined plates (point B is directly above the center of A₁) B 100 mm A₂ - 220 mm (c) (d) Long cylinder lying on infinite plane + A₁ Az (d) (e) Hemisphere-disk arrangement -A₂, hemisphere, diameter D A₂ A₁, disk, diameter D/2 (e) (f) Long, open channel 1 m AA₂ 2 m (f) (g) Long cylinders with A₁ = 4A₁. Also, what is F₁₂? -D₁ A1 -A₂ -D2 (e) (h) Long, square rod in a long cylinder. Also, what is F22? w=D/5 18 A₁ -A2 (h) -Darrow_forward13.9 Determine the shape factor, F12, for the rectangles shown. 6 m 1 3 m 6 m 1 m 2 6 m 1 0.5 m 2 1 m (a) Perpendicular rectangles without a common edge. -1 m. (b) Parallel rectangles of unequal areas.arrow_forwardI keep getting the wrong answer i have gotten 6519.87 and 319.71arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license