Videos
- a. What circuit supplies the workshop lighting? ________________
- b. What circuit supplies the plug-in strip over the workbench? ________________
- c. What circuit supplies the freezer receptacle? ________________
(a)
Mention the type of circuit that is used to supply the workshop lighting.
Answer to Problem 1R
The circuit used to supply the workshop lighting is A17.
Explanation of Solution
Discussion:
Refer to Figure 18-1 in the textbook that shows the conduit layout for workshop. In this layout, the lighting circuit is supplied by the branch circuit A17. In addition to supply the lighting, the circuit A17 also feeds the ceiling exhaust fan and chime transformer.
Conclusion:
Thus, the circuit used to supply the workshop lighting is A17.
(b)
Mention the type of circuit that is used to supply the plug-in strip over the workbench.
Answer to Problem 1R
The circuit used to supply the plug-in strip receptacles over the workbench is A18.
Explanation of Solution
Discussion:
Refer to Figure 18-1 in the textbook that shows the conduit layout for workshop. The plug-in strip receptacles and the receptacles connected to the right of the main panelboard are supplied with circuit A18. The receptacles mounted in an unfinished basement are protected with GFCI protection and accomplished by installing GFCI receptacles or GFCI circuit breakers in panelboard A.
Conclusion:
Thus, the circuit used to supply the plug-in strip receptacles over the workbench is A18.
(c)
Mention the type of circuit that is used to supply the freezer receptacle.
Answer to Problem 1R
The circuit used to supply the freezer receptacle is A13.
Explanation of Solution
Discussion:
Refer to Figure 18-1 in the textbook that shows the conduit layout for workshop. In this layout, the freezer single receptacle is supplied with circuit A13. Refer to Figure 18-9 in the textbook that shows the outlet boxes (a handy box) used for the freezer receptacles.
Conclusion:
Thus, the circuit used to supply the freezer receptacle is A13.
Want to see more full solutions like this?
Chapter 18 Solutions
ELECTRICAL WIRING:RESIDENTAL-6 PLANS
Additional Engineering Textbook Solutions
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
SURVEY OF OPERATING SYSTEMS
Mechanics of Materials (10th Edition)
Problem Solving with C++ (10th Edition)
Vector Mechanics For Engineers
Elementary Surveying: An Introduction To Geomatics (15th Edition)
- Solve on paper not using chatgptarrow_forwardAssume that a building manager instructed you to install a water heater. The specs on the water heater nameplate reveals the following 240V, 2PH, 60HZ, 5.7KW. The manager insisted for the installation to be done with 10 AWG copper THWN-2 conductor, the length of run is 1200 FT away from the service panel. Calculate the voltage after the installation.arrow_forwardPlease confirm that my solution is correct, especially the block diagram. Please DRAW (not type) what the block diagram would look like if it's incorrect. thank youarrow_forward
- use this code on the bottom to answer the question in the photo clc; clearvars; % Read the file [y, Fs] = audioread('106miles.wav'); N = length(y); Nfft = 2^nextpow2(N); dt = 1/Fs; t = (0:dt:(N-1)*dt)'; % Ensure t is a column vector y = y - mean(y); % Remove DC component (if not already zero-mean) % Carrier signal (25 kHz) fc = 25000; % Carrier frequency in Hz carrier = cos(2 * pi * fc * t); % DSB-SC Modulation modulated_signal = y .* carrier; % Plot Time Domain Signal figure; subplot(2,1,1); plot(t, y); title('Original Signal (Time Domain)'); xlabel('Time (s)'); ylabel('Amplitude'); subplot(2,1,2); plot(t, modulated_signal); title('DSB-SC Modulated Signal (Time Domain)'); xlabel('Time (s)'); ylabel('Amplitude'); % Frequency Domain (FFT) Y = fft(y, Nfft) / Nfft; Modulated_Y = fft(modulated_signal, Nfft) / Nfft; f = Fs * (0:(Nfft/2)) / Nfft; % Frequency vector % Plot Frequency Domain Signal figure; subplot(2,1,1); plot(f, abs(Y(1:Nfft/2+1))); title('Original Signal…arrow_forward5-9 A 230 V shunt motor has a nominal arma- ture current of 60 A. If the armature resist- ance is 0.152, calculate the following: a. The counter-emf [V] b. The power supplied to the armature [W] c. The mechanical power developed by the motor, [kW] and [hp] 5-10 a. In Problem 5-9 calculate the initial start- ing current if the motor is directly con- nected across the 230 V line. b. Calculate the value of the starting resistor needed to limit the initial current to 115 A.arrow_forwardhow to solve this?arrow_forward
- For the circuit in Fig. P8.52, choose the load impedance ZLso that the power dissipated in it is a maximum. How much powerwill that be?arrow_forwardhow to solve the attached question? please explain or give reference where required in the solution.arrow_forwardHANDWRITTEN SOLUTION REQUIRED NOT USING CHATGPTarrow_forward
EBK ELECTRICAL WIRING RESIDENTIALElectrical EngineeringISBN:9781337516549Author:SimmonsPublisher:CENGAGE LEARNING - CONSIGNMENT