
Concept explainers
Find the speed of the rod relative to the tube when

Answer to Problem 17.88P
The speed of the rod relative to the tube when
Explanation of Solution
Given information:
The mass
The mass
The angular velocity
Calculation:
Consider l is the length of the rod and the tube and O is the point of intersection of the tube and axle.
Write the equation of the centroidal mass moment of inertia
Write the equation of the centroidal mass moment of inertia
Write the equation of the tangential equation of the tube using kinematics.
Substitute
Write the equation of the tangential equation of the rod using kinematics.
Substitute
Find the equation of angular momentum about point O.
Substitute
Find the equation of kinetic energy.
Substitute
Substitute Equation (1) in Equation (2),
All the motion in the system is horizontal. Therefore, the potential energy is zero.
Consider the initial position.
At the initial position, the initial angular velocity of the system is 5 rad/s and the radial velocity is zero.
Find the angular momentum at the initial position using equation (1).
Substitute 0 for x.
Substitute 6 kg for
Find the kinetic energy at initial position using equation (3).
Substitute
Consider the final position.
Find the angular momentum at the final position using equation (1).
Substitute 0.4 m for x.
Substitute 6 kg for
Find the kinetic energy at final position using equation (3).
Substitute
Consider the conservation of angular momentum.
Substitute
Find the speed of the rod relative to the tube when
Consider the conservation of energy.
Substitute
Substitute
Thus, the speed of the rod relative to the tube when
Want to see more full solutions like this?
Chapter 17 Solutions
Vector Mechanics for Engineers: Statics and Dynamics
- HW12 A multiple-disc clutch has five plates having four pairs of active friction surfaces. If the intensity of pressure is not to exceed 0.127 N/mm², find the power transmitted at 500 r.p.m. The outer and inner radii of friction surfaces are 125 mm and 75 mm respectively. Assume uniform wear and take the coefficient of friction = 0.3.arrow_forwardThe sketch below gives some details of the human heart at rest. What is the total power requirement (work/time) for an artificial heart pump if we use a safety factor of 5 to allow for inefficiencies, the need to operate the heart under stress, etc.? Assume blood has the properties of water. p pressure above atmosphere blood going to the lungs for a fresh charge of oxygen p = 2.9 kPa 25v pulmonary artery d = 25mm fresh oxygenated blood from the lungs p = 1.0 kPa vena cava d=30mm right auricle pulmonary vein, d = 28mm aorta, d=20mm spent blood returning from left auricle the body p = 0.66 kPa right left ventricle ventricle blood to feed the body, p 13 kPa normal blood flow = 90 ml/sarrow_forward4- A horizontal Venturi meter is used to measure the flow rate of water through the piping system of 20 cm I.D, where the diameter of throat in the meter is d₂ = 10 cm. The pressure at inlet is 17.658 N/cm2 gauge and the vacuum pressure of 35 cm Hg at throat. Find the discharge of water. Take Cd = 0.98.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





