Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 16, Problem 3ASRQ
While measuring the resistance of a wire with an ohmmeter: Technician A says that if low resistance is shown on the meter, the wire is shorted. Technician B says that if no resistance is measured, the wire is shorted. Who is correct?
- Technician A
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
What does the voltage measurement across the conductor indicate?
HAL
3.01 v
The wire has high resistance.
The wire is okay.
The wire is open.
The wire condition can't be determine.
2.A. You can usually check for a leak in a vacuum system by looking at or feelingA. at the exhaust of the vacuum pump.B. at the vacuum gauge at the vacuum pump.C. for signs of dirt on the piping.
2.B. When you measure the voltage drop across a set of contacts, you'reA. checking the quality of the contact set.B. sensing how much current is flowing in the circuit.C. measuring the equivalent motor resistance.
2.C. A chain-drive system can be aligned easier than a belt-drive system since the chain-drive systemA. can have a string left on the sprockets after the alignment is complete.B. can have the chain removed while the final alignment is taking place.C. is less critical to misalignment.
Which of the following statement is correct
related to orifice meter.
Orifice meter is a discharge measuring
instrument
Orifice meter is a Pressure head
measuring instrument
Orifice meter is a pressure measuring
instrument
Orifice meter is a velocity measuring
instrument
Chapter 16 Solutions
Automotive Technology
Ch. 16 - How will an electrical circuit behave if there is...Ch. 16 - What happens to an electrical circuit when there...Ch. 16 - Prob. 3SACh. 16 - What type of solder should be used to repair...Ch. 16 - True or False? The MIN/MAX function on some DMMs...Ch. 16 - True or False? A zero reading on an ohmmeter means...Ch. 16 - Prob. 3TFCh. 16 - While troubleshooting a problem, the key to...Ch. 16 - Prob. 5TFCh. 16 - Prob. 1MC
Ch. 16 - Prob. 2MCCh. 16 - Wiring harnesses are typically shielded by plastic...Ch. 16 - Which of the following lab scope controls must be...Ch. 16 - Prob. 5MCCh. 16 - Which of the following information is not given in...Ch. 16 - While discussing electricity: Technician A says...Ch. 16 - While discussing NTC thermistors: Technician A...Ch. 16 - While measuring the resistance of a wire with an...Ch. 16 - While testing variable resistors: Technician A...Ch. 16 - Prob. 5ASRQCh. 16 - Technician A uses a testlight to test circuit...Ch. 16 - Technician A uses a testlight to detect...Ch. 16 - While diagnosing the location of a wire-to-wire...Ch. 16 - While measuring resistance: Technician A uses an...Ch. 16 - While discussing how to test a switch: Technician...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False? A lab scope is a visual voltmeter that shows voltage over a period of time.arrow_forwardDescribe how a meter would be connected in a circuit to measure the potential difference across a light bulb.arrow_forwardWhile discussing copper wire: Technician A says that if the length of wire is doubled, the resistance between the wire ends is doubled. Technician B says that if the diameter of a wire is doubled, the resistance between the wire ends is doubled. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While measuring resistance: Technician A uses an ohmmeter to measure resistance of a component before disconnecting it from the circuit. Technician B uses a voltmeter to measure voltage drop. A circuit with very low resistance will drop zero or very little voltage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardChoose True or Falsearrow_forwardIn reading dial indicators, the sensitivity of the long needle is meter.arrow_forward
- What is the function of the following temperature measuring instruments Thermometers Bulb and Capillary Sensor Sealed Bellowsarrow_forwardIf H=16cm, what is the pressure gauge reading? Air H. 4m Water Hgarrow_forwardTrue or False. In measurement there must be one-to-one correspondence between the numbers and the characteristics being measured. True Falsearrow_forward
- The following transducer is used to measure the temperature. a. Bourdon tube b. Bellows c. Thermocouple d. Strain Gaugearrow_forwardTrue or False 1. It is acceptable to use a hoist to lift something that weighs more than the rating on the hoist when the load is lifted carefully. 2. Typically, combustible material accidents occur at higher temperatures while flammable material accidents occur at room temperature. 3. Water reactive chemicals include calcium carbide, cyclooctene, metal hydrides, and metals like sodium and potassium. 4. When driving material lifting equipment, workers should maintain at least a 5-foot clearance from overhead power lines. 5. Workers should use at least 2 straps placed equally from the center when lifting a long I-beam. ******************************************************************************************** Multiple Choice 1. Which of the following chemicals is not considered a liver toxin? A. Glacial acetic acid B. Carbon Tetrachloride C. Ethanol D. Trichloroethylene 2. Which of the following is a safety practice intended to protect workers from a lightning strike? A. Use a metal…arrow_forwardWhy should gauges be installed only after there is evidence that they are needed?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY