Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 16, Problem 6ASRQ
Technician A uses a testlight to test circuit protection devices. Technician B uses a voltmeter to test circuit protection devices. Who is correct?
- Technician A
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
1. What type of measurements are most often obtained when testing vehicle circuits ?
2. What measurement is common in testing audio system and many modern door lock system ?
True or False
1. It is acceptable to use a hoist to lift something that weighs more than the rating on the hoist when the load is lifted carefully.
2. Typically, combustible material accidents occur at higher temperatures while flammable material accidents occur at room temperature.
3. Water reactive chemicals include calcium carbide, cyclooctene, metal hydrides, and metals like sodium and potassium.
4. When driving material lifting equipment, workers should maintain at least a 5-foot clearance from overhead power lines.
5. Workers should use at least 2 straps placed equally from the center when lifting a long I-beam.
********************************************************************************************
Multiple Choice
1. Which of the following chemicals is not considered a liver toxin?
A. Glacial acetic acid
B. Carbon Tetrachloride
C. Ethanol
D. Trichloroethylene
2. Which of the following is a safety practice intended to protect workers from a lightning strike?
A. Use a metal…
From the following identify the true
statement relating to the term Preventive
maintenance
The maintenance done after the failure
of machine and can't save energy
during the process.
O The maintenance done before the failure
of machine and can save energy during
the process.
O The maintenance done before the failure
of machine and can't save energy
during the process.
The maintenance done after the failure
of machine and can save energy during
the process.
Chapter 16 Solutions
Automotive Technology
Ch. 16 - How will an electrical circuit behave if there is...Ch. 16 - What happens to an electrical circuit when there...Ch. 16 - Prob. 3SACh. 16 - What type of solder should be used to repair...Ch. 16 - True or False? The MIN/MAX function on some DMMs...Ch. 16 - True or False? A zero reading on an ohmmeter means...Ch. 16 - Prob. 3TFCh. 16 - While troubleshooting a problem, the key to...Ch. 16 - Prob. 5TFCh. 16 - Prob. 1MC
Ch. 16 - Prob. 2MCCh. 16 - Wiring harnesses are typically shielded by plastic...Ch. 16 - Which of the following lab scope controls must be...Ch. 16 - Prob. 5MCCh. 16 - Which of the following information is not given in...Ch. 16 - While discussing electricity: Technician A says...Ch. 16 - While discussing NTC thermistors: Technician A...Ch. 16 - While measuring the resistance of a wire with an...Ch. 16 - While testing variable resistors: Technician A...Ch. 16 - Prob. 5ASRQCh. 16 - Technician A uses a testlight to test circuit...Ch. 16 - Technician A uses a testlight to detect...Ch. 16 - While diagnosing the location of a wire-to-wire...Ch. 16 - While measuring resistance: Technician A uses an...Ch. 16 - While discussing how to test a switch: Technician...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While measuring resistance: Technician A uses an ohmmeter to measure resistance of a component before disconnecting it from the circuit. Technician B uses a voltmeter to measure voltage drop. A circuit with very low resistance will drop zero or very little voltage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? A lab scope is a visual voltmeter that shows voltage over a period of time.arrow_forwardWhile measuring the resistance of a wire with an ohmmeter: Technician A says that if low resistance is shown on the meter, the wire is shorted. Technician B says that if no resistance is measured, the wire is shorted. Who is correct? Technician A Technician B Both A and B d. Neither A nor Barrow_forward
- While checking an A/C compressor clutch coil clamping diode with a DMM, the meter shows infinite resistance when the diode is measured in both directions: Technician A says that the diode is open. Technician B says that all diodes should behave this way until a specified voltage is applied to them. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTrue or False? The same information available in service manuals and bulletins may also be available electronically on DVDs and the Internet.arrow_forwardWhich of the following tests would not be performed to check for high resistance in the battery' cables? Cranking voltage test Insulated circuit resistance test Starter relay by-pass test Ground circuit resistance testarrow_forward
- Technician A uses a high-impedance testlight on the high-voltage systems in hybrid vehicles. Technician B uses only CAT-III test instruments to check high- voltage systems. Who is correct? Technician A Both A and B Technician B Neither A nor Barrow_forwardAll gauges operate but read lower than normal: Technician A says that the connection to the instrument cluster may be corroded. Technician B says that the cluster s IVR may be open. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing electrical grounds: Technician A says that a component may be grounded through its mounting to a major metal part. Technician B says that some components must be grounded by connecting its positive terminal to a metal section of the frame. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While discussing diagnostic procedures: Technician A says that after the visual inspection has been performed, the DTCs should be cleared from the memory of the PCM. Technician B says that serial data can be helpful when there are no DTCs but there is a fault in the system. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing copper wire: Technician A says that if the length of wire is doubled, the resistance between the wire ends is doubled. Technician B says that if the diameter of a wire is doubled, the resistance between the wire ends is doubled. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing the results of a load test: Technician A says that if a battery fails a load test but the voltage rises above 12.4 volts when the load is removed, the battery should be replaced. Technician B says that if a battery fails a load test but the voltage rises above 12.4 volts when the load is removed, the battery is able to hold a charge. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
General Industrial Safety; Author: Jim Pytel;https://www.youtube.com/watch?v=RXtF_vQRebM;License: Standard youtube license