Concept explainers
The acceleration of pin P.
Answer to Problem 15.183P
The acceleration of pin P is
Explanation of Solution
Given information:
The constant angular velocity of the bar AD is
The angular velocity of the bar BE is
The angular acceleration of the bar BE is
Calculation:
Calculate the slope of the bar BE
Calculate the position
The position of P with respect to A.
The position of P with respect to B.
Provide the angular velocities of the bar AD
Provide the angular acceleration of the bar BE in vector form as shown below.
Calculate the velocity of a point
Here,
Consider that the point P in the frame AD.
Calculate the velocity component
Substitute
Calculate the velocity component
Here,
Calculate the velocity of a point
Substitute
Consider that the point P in the frame BE.
Calculate the velocity component
Substitute
Calculate the velocity component
Here,
Resolving along x and y direction.
Substitute
Equating Equations (3) and (5) as shown below.
Resolving i and j components as shown below.
For i component.
Substitute
Calculate the velocity component
Substitute
For j component.
Substitute
Calculate the velocity component
Substitute
Calculate the acceleration of a point
Here,
Consider the point P in the frame AD.
Calculate the acceleration component
Here,
Substitute
Calculate the acceleration component
Here,
Substitute
Calculate the Coriolis component of acceleration
Substitute
Substitute
Consider the point P in the frame BE.
Calculate the acceleration component
Substitute
Calculate the acceleration component
Here,
Resolving along x and y direction.
Calculate the Coriolis component of acceleration
Substitute
Calculate the acceleration of a point
Substitute
Equating Equations (7) and (8) as shown below.
Resolving i and j components as shown below.
Substitute
Calculate the acceleration of a point
Substitute
Calculate the magnitude of the acceleration
Therefore, the acceleration of pin P is
Want to see more full solutions like this?
Chapter 15 Solutions
<LCPO> VECTOR MECH,STAT+DYNAMICS
- (b) A steel 'hot rolled structural hollow section' column of length 5.75 m, has the cross-section shown in Figure Q.5(b) and supports a load of 750 kN. During service, it is subjected to axial compression loading where one end of the column is effectively restrained in position and direction (fixed) and the other is effectively held in position but not in direction (pinned). i) Given that the steel has a design strength of 275 MN/m², determine the load factor for the structural member based upon the BS5950 design approach using Datasheet Q.5(b). [11] ii) Determine the axial load that can be supported by the column using the Rankine-Gordon formula, given that the yield strength of the material is 280 MN/m² and the constant *a* is 1/30000. [6] 300 600 2-300 mm wide x 5 mm thick plates. Figure Q.5(b) L=5.75m Pinned Fixedarrow_forwardHelp ارجو مساعدتي في حل هذا السؤالarrow_forwardHelp ارجو مساعدتي في حل هذا السؤالarrow_forward
- Q2: For the following figure, find the reactions of the system. The specific weight of the plate is 500 lb/ft³arrow_forwardQ1: For the following force system, find the moments with respect to axes x, y, and zarrow_forwardQ10) Body A weighs 600 lb contact with smooth surfaces at D and E. Determine the tension in the cord and the forces acting on C on member BD, also calculate the reaction at B and F. Cable 6' 3' wwwarrow_forward
- Help ارجو مساعدتي في حل هذا السؤالarrow_forwardQ3: Find the resultant of the force system.arrow_forwardQuestion 1 A three-blade propeller of a diameter of 2 m has an activity factor AF of 200 and its ratio of static thrust coefficient to static torque coefficient is 10. The propeller's integrated lift coefficient is 0.3.arrow_forward
- (L=6847 mm, q = 5331 N/mm, M = 1408549 N.mm, and El = 8.6 x 1014 N. mm²) X A ΕΙ B L Y Marrow_forwardCalculate the maximum shear stress Tmax at the selected element within the wall (Fig. Q3) if T = 26.7 KN.m, P = 23.6 MPa, t = 2.2 mm, R = 2 m. The following choices are provided in units of MPa and rounded to three decimal places. Select one: ○ 1.2681.818 O 2. 25745.455 O 3. 17163.636 O 4. 10727.273 ○ 5.5363.636arrow_forwardIf L-719.01 mm, = 7839.63 N/m³, the normal stress σ caused by self-weight at the location of the maximum normal stress in the bar can be calculated as (Please select the correct value of σ given in Pa and rounded to three decimal places.) Select one: ○ 1. 1409.193 2. 845.516 O 3. 11273.545 ○ 4.8455.159 ○ 5.4509.418 6. 2818.386 7.5636.772arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY