Q3. Determine the reaction force at A and force P applied at 45° to the horizontal just necessary to start aroller 100 cm diameter over an obstruction 25 cm high, if the roller weighs 1000 N, as shown in Fig. 3.Fig. (3)

Given Data:Roller diameter = 100 cm → Radius r = 50cm = 0.5 mObstruction height h = 25 cm = 0.25…

Answered: Q3. Determine the reaction force at A…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.38P: Two concrete blocks weighing 320 lb each form part of the retaining wall of a swimming pool. Will...

See similar textbooks

Similar questions

The uniform ladder of weight W is raised slowly by applying a vertical force P to the rope at A. Show that P is independent of the angle .
The cable AOB weighs 5.2 N/m. When the horizontal 30-N force is applied to the roller support at B, the sag in the cable is 5 m. Find the span L of the cable.
A 10-m uniform beam of weight 100 N is supported by two ropes at its ends. If a 400-N person sits at the center of the beam, what is the tension in the right rope?
The 600-lb box is held in place on the smooth bed of the dump truck by the rope AB. Find: (a) if a = 25°, what is the tension in the rope? (b) if the rope will safely support a tension of 400 lb, what is the maximum allowable value of a T a B
A uniform beam ( weight 71 N, length 6m) is being supported by cable and a hinge on a wall. The cable is attached to the beam 4 m from the hinge. A 100 Newton sign hangs off the end of the beam. a. Determine the tension in the cable b. Determine the horizontal and vertical components of the force provided by the hinge
3. A 30 kg, 2 meter long rod is sticking out from a building, and it is attached by a hinge. A 20 kg rock is hanging from the end of the rod. To keep the rod from rotating around the hinge (and the rock from falling) a long cable has been attached to the building 2 meters above the r and tied to the end of the rod. a. What is the tension in the cable? Hint, the rod's mass can all be assumed to be at the center of mass of the rod. b. What is the normal force of the building on the end of the rod? 2m 2m
How to answer this? I can't find similar problems online.
The supporting structure of the billboard is attached to the ground by a pin at B, and its rear leg rests on the ground at A. Friction may be neglected. Point G is the center of gravity of the billboard and structure, which together weigh 2800 lb. To prevent tipping over in high winds, a 2370-lb weight is placed on the structure near A, as shown. (a) Compute the magnitudes of the reactions at A and B if the wind load on the billboard is q = 120 lb/ft.
Q.3) A 10 kg bracket ABC is positioned on a table where gravity acts into the drawing (z direction). The bracket is pinned at A and is constrained by a fixed pin in the smooth (negligible friction) slot B. Assume the pin at B is only in contact with one surface of the slot at a time. An external clockwise moment of 120 N-m is applied at C. Compute the horizontal and vertical support reactions at pin A as well as the reaction at pin B. State whether pin B is in contact with the upper left or lower right surface of the slot. 200 mm 150 mm 35 A 120 N-m
Q.5) A steel bar OC with attached spring at B and cable at C can rotate freely in a horizontal plane about support at O as shown below. The spring is upstretched when C is coincident with A. Determine the tension T required to hold the steel bar OC in the 40° position shown as a function of k and L. Neglect the weight of the bar OC and the diameter of the pulley at D. 40° L/2 B m T L/2 25°
The supporting structure of the billboard is attached to the ground by a pin at B, and its rear leg rests on the ground at A. Friction may be neglected. Point G is the centre of the gravity of the billboard and structure, which together weigh 2800 lb. To prevent tipping over in high winds, a 2370-lb weight is placed on the structure near A , as shown. (a) Compute the magnitudes of the reactions at A and B if the wind load on the billboardis q = 120lb/ft. (b) Find the smallest wind loads q that would cause the structure to tip over.
Please don't provide handwritten solution ....

SEE MORE QUESTIONS

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L