Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 15, Problem 5P
Select two of the methods used to produce and hold molten metal, and compare their relative efficiencies. Under what conditions might the lower efficiency method actually be preferred?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Why are aluminum and copper alloys unsuitable for use in hot chamber die casting
Converging passage is used for feeding the liquid molten metal into the mould to
(a) increase the rate of feeding
(b) quickly break off the protruding portion
of the casting
(c) decrease wastage of cast metal
(d) avoid aspiration of airA
Converging passage is used for feeding the liquid molten metal into the mould to
(a) increase the rate of feeding
(b) quickly break off the protruding portion
of the casting
(c) decrease wastage of cast metal
(d) avoid aspiration of air
Chapter 15 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 15 - What are some of the major disadvantages of the...Ch. 15 - What are some possible limitations of multiple-use...Ch. 15 - Prob. 3RQCh. 15 - Prob. 4RQCh. 15 - Why do permanent-mold castings generally have...Ch. 15 - Prob. 6RQCh. 15 - What is semipermanent-mold casting?Ch. 15 - Why might low production runs be unattractive for...Ch. 15 - Prob. 9RQCh. 15 - In addition to the mold cavity, what additional...
Ch. 15 - Prob. 11RQCh. 15 - Prob. 12RQCh. 15 - Prob. 13RQCh. 15 - Prob. 14RQCh. 15 - Prob. 15RQCh. 15 - Prob. 16RQCh. 15 - What types of products would be possible...Ch. 15 - Prob. 18RQCh. 15 - What are the most common die-cast materials?Ch. 15 - Contrast the materials used to make dies for...Ch. 15 - Prob. 21RQCh. 15 - Prob. 22RQCh. 15 - Prob. 23RQCh. 15 - Prob. 24RQCh. 15 - Prob. 25RQCh. 15 - Prob. 26RQCh. 15 - How does the air in the mold cavity escape in the...Ch. 15 - Are risers employed in die casting? Can sand cores...Ch. 15 - Prob. 29RQCh. 15 - Give some examples of cast-in inserts.Ch. 15 - Prob. 31RQCh. 15 - Prob. 32RQCh. 15 - Prob. 33RQCh. 15 - Prob. 34RQCh. 15 - Prob. 35RQCh. 15 - What is a thixotropic material? How does it...Ch. 15 - What are some of the attractive features of...Ch. 15 - Describe the inner surface profile of true...Ch. 15 - Prob. 39RQCh. 15 - Prob. 40RQCh. 15 - Prob. 41RQCh. 15 - Prob. 42RQCh. 15 - Prob. 43RQCh. 15 - What types of equipment are used by foundries to...Ch. 15 - What are some of the factors that influence the...Ch. 15 - What are some of the possible feedstock materials...Ch. 15 - What types of metals are commonly melted in...Ch. 15 - What are some of the ways that the melting rate of...Ch. 15 - What are some of the pros and cons of indirect...Ch. 15 - Prob. 50RQCh. 15 - Prob. 51RQCh. 15 - Prob. 52RQCh. 15 - What are the primary functions of a pouring...Ch. 15 - Prob. 54RQCh. 15 - Prob. 55RQCh. 15 - What are some common ways to remove cores from...Ch. 15 - Prob. 57RQCh. 15 - Prob. 58RQCh. 15 - What is the difference between infiltration and...Ch. 15 - Prob. 60RQCh. 15 - What are some of the ways that industrial robots...Ch. 15 - Prob. 62RQCh. 15 - Prob. 63RQCh. 15 - Attractive properties for casting alloys include...Ch. 15 - Prob. 2PCh. 15 - Prob. 3PCh. 15 - Prob. 4PCh. 15 - Select two of the methods used to produce and hold...Ch. 15 - Prob. 7PCh. 15 - Discuss the various features that this component...Ch. 15 - Prob. 3CSCh. 15 - Prob. 4CSCh. 15 - Prob. 5CSCh. 15 - Prob. 6CS
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True centrifugal casting is performed horizontally to make large diameter copper tube sections. The tubes have a length = 2.0 m, outside diameter = 0.4 m, and wall thickness = 30 mm. (a) If the rotational speed of the pipe = 600 rev/min, determine the G-factor on the molten metal. (b) Is the rotational speed sufficient to avoid "rain?" (c) What volume of molten metal must be poured into the mould to make the casting if solidification shrinkage and contraction after solidification are considered? Solidification shrinkage for copper = 3.5%, and solid thermal contraction = 6.5%.arrow_forwardDiscuss the various stages in Quenching process with neat sketches.arrow_forwardWhich among the following design considerations for casting to be followed to reduce stress concentration in parts? O a. Shape the casting for orderly solidification O b. Avoid abrupt changes in cross section Oc Avoid thin sections O d. Make provision for easy removal of pattern from the mouldarrow_forward
- What is the advantage in casting turbine blades that have either highly aligned grain boundaries or no grain boundaries at all?arrow_forward: True centrifugal casting is performed horizontally to make large diameter copper tube sections. The tubes have a length= 1.0 m, diameter= 0.25 m, and wall thickness = 15 mm. (a) If the rotational speed of the pipe = 700 rev/min, determine the G-factor on the molten metal. (b) What volume of molten metal must be poured into the mold to make the casting if solidification shrinkage and contraction after solidification are considered? Solidification shrinkage for copper = 4.5%, and solid thermal contraction = 7.5%? %3Darrow_forwardA slab of size 300 x 300 x 50 mm is reguire to be cast from a molten steel using a top riser of 170 mm diameter. If (dh) = 2 for riser, calculate the freezing ratio. %3Darrow_forward
- I need the answer as soon as possiblearrow_forwarda riser in the shape of a sphere is to be designed for a sand casting mold. the casting is a rectangular plate, with length 200mm, width 100mm, and thickness 18mm. if the total solidification time of the casting itself is known to be 3.5 mm, determine the diameter of the riser so that it will take 25% longer for the riser to solidify. assume a value of 2 for ‘n’ m( the exponent in chvorinov’s rule). know the volume and surface area of a sphere.arrow_forwardA true centrifugal casting operation is to be performed in a horizontal configuration by Durban Foundry to make cast iron pipe sections. The sections will have a length = 95 cm, outside diameter = 20 cm, and wall thickness = 1.00 cm. If the rotational speed of the pipe = 490 rev/min, Determine the G-factor, b) Is the operation likely to be successful?arrow_forward
- Describe the detailed processes about the Expendable-Pattern casting. Please use numbered lists to show each step and process.arrow_forward3) The dihedral wetting angle between solid- liquid interface with lowest solidification cracking tendency under identical welding conditions is 0° O45° 60° 90°arrow_forwardEX.3//A cylindrical riser must be designed for a sand-casting mold. The casting itself is a steel rectangular plate with dimensions 7.5 cm x 12.5 cm x 2.0 cm. Previous observations have indicated that the total solidification time (TTs) for this casting =1.6 min. The cylinder for the riser will have a diameter-to-height ratio=1.0. Determine the dimensions of the riser so that its TTS = 2.0 min.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Casting Metal: the Basics; Author: Casting the Future;https://www.youtube.com/watch?v=2CIcvB72dmk;License: Standard youtube license