Explanation Assumption: The sign conventions for the stress components are explained below. The outward normal on the right-hand face of the element is representing as the positive x and x ' axes. The normal stress σ x and σ x ' are positive if it acts along the positive x and x ' axes. The normal stress σ y and σ y ' are positive if it acts along the positive y and y ' axes. The shear stress τ x y and τ x ' y ' are positive if it acts along the positive x and x ' & y and y ' axes. Calculation: Apply sign conventions to the given Figure. The value of normal stresses are σ x = 80 kPa and σ y = 0 . The value of shear stress is τ x y = 30 kPa . The procedure to construct Mohr’s circle is shown below. The coordinate systems are the horizontal axis represents the normal stress with positive towards right and the vertical axis represents shear stress with positive downwards. Plot the center of the circle C which is located σ avg = σ x + σ y 2 from the origin. Plot the reference points A having coordinates A ( σ x , τ x y ) . This point represents that the x ′ axis coincides with the x axis. Hence, θ = 0 ° . Connect the point A with the centre C and find CA by trigonometry which represents the radius of the circle R . Sketch the circle. Find the average normal stress ( σ avg ) using the relation: σ avg = σ x + σ y 2 (1) Substitute 80 kPa for σ x and 0 for σ y in Equation (1). σ avg = 80 + 0 2 = 40 kPa Therefore, the coordinates of the reference point C is ( 40 , 0 ) . The coordinates of the reference point A ( σ x , τ x y ) = ( 80 , 0 ) . Find the radius of the circle using the relation: R = ( σ x − σ avg ) 2 + ( τ x y ) 2 (2) Substitute 40 kPa for σ avg , 80 kPa for σ x , and 30 kPa for τ x y in Equation (2)

Statics and Mechanics of Materials Plus Mastering Engineering with Pearson eText - Access Card Package (5th Edition)

5th Edition

ISBN: 9780134301006

Author: Russell C. Hibbeler

Publisher: PEARSON

See similar textbooks

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain b…

Videos

Question

Chapter 14.4, Problem 8FP

To determine

Find the principal stresses.

Find the orientation of the principal stresses.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 14.4, Problem 7FP

Chapter 14.4, Problem 9FP

Students have asked these similar questions

Please can you help with ten attatched question?

An AISI 1018 steel ball with 1.100-in diameter is used as a roller between a flat plate made from 2024 T3 aluminum and a flat table surface made from ASTM No. 30 gray cast iron. Determine the maximum amount of weight that can be stacked on the aluminum plate without exceeding a maximum shear stress of 19.00 kpsi in any of the three pieces. Assume the figure given below, which is based on a typical Poisson's ratio of 0.3, is applicable to estimate the depth at which the maximum shear stress occurs for these materials. 1.0 0.8 Ratio of stress to Pmax 0.4 90 0.6 στ Tmax 0.2 0.5a a 1.5a 2a 2.5a За Distance from contact surface The maximum amount of weight that can be stacked on the aluminum plate is lbf.

A carbon steel ball with 27.00-mm diameter is pressed together with an aluminum ball with a 36.00-mm diameter by a force of 11.00 N. Determine the maximum shear stress and the depth at which it will occur for the aluminum ball. Assume the figure given below, which is based on a typical Poisson's ratio of 0.3, is applicable to estimate the depth at which the maximum shear stress occurs for these materials. 1.0 0.8 Ratio of stress to Pma 9 0.6 στ 24 0.4 Tmax 0.2 0 0.5a a 1.5a Z 2a 2.5a За Distance from contact surface The maximum shear stress is determined to be MPa. The depth in the aluminum ball at which the maximum shear stress will occur is determined to be [ mm.

Chapter 14 Solutions

Statics and Mechanics of Materials Plus Mastering Engineering with Pearson eText - Access Card Package (5th Edition)

Ch. 14.3 - In each ease, the state of stress x, y, xy...Ch. 14.3 - Given the state of stress shown on the element,...Ch. 14.3 - Determine the normal stress and shear stress...Ch. 14.3 - Prob. 2FP Ch. 14.3 - Determine the equivalent state of stress on an...Ch. 14.3 - Prob. 4FP Ch. 14.3 - The beam is subjected to the load at its end....Ch. 14.3 - Prob. 6FP Ch. 14.3 - Prove that the sum of the normal stresses x+y=x+y...Ch. 14.3 - Determine the stress components acting on the...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Find the principal stresses. Find the orientation of the principal stresses.

Solution Summary: The author explains the sign conventions for the stress components and the procedure to construct Mohr's circle.