Engineering Mechanics: Statics & Dynamics (14th Edition)
14th Edition
ISBN: 9780133915426
Author: Russell C. Hibbeler
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 14.4, Problem 53P
The sports car has a mass of 2.3 Mg, and while it is traveling at 28 m/s the driver causes it to accelerate at 5 m/s2 If the drag resistance on the car due to the wind is F0 = (0.3v2) N, where V is the velocity in m/s, determine the power supplied to the engine at this instant. The engine has a running efficiency ɛ = 0.68.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The answers to this question s wasn't properly given, I need expert handwritten solutions
I need expert handwritten solutions to this only
Two large tanks, each holding 100 L of liquid, are interconnected by pipes, with the liquid flowing from tank
A into tank B at a rate of 3 L/min and from B into A at a rate of 1 L/min (see Figure Q1). The liquid inside each
tank is kept well stirred. A brine solution with a concentration of 0.2 kg/L of salt flows into tank A at a rate of
6 L/min. The diluted solution flows out of the system from tank A at 4 L/min and from tank B at 2 L/min. If,
initially, tank A contains pure water and tank B contains 20 kg of salt.
A
6 L/min
0.2 kg/L
x(t)
100 L
4 L/min
x(0) = 0 kg
3 L/min
B
y(t)
100 L
y(0) = 20 kg
2 L/min
1 L/min
Figure Q1 - Mixing problem for interconnected tanks
Determine the mass of salt in each tank at time t > 0:
Analytically (hand calculations)
Chapter 14 Solutions
Engineering Mechanics: Statics & Dynamics (14th Edition)
Ch. 14.3 - Determine the work of the force when it displaces...Ch. 14.3 - Determine the kinetic energy of the 10-kg block.Ch. 14.3 - Prob. 1FPCh. 14.3 - If the motor exerts a constant force of 300 N on...Ch. 14.3 - If the motor exerts a force of F = (600 + 2s2) N...Ch. 14.3 - The 1.8-Mg dragster is traveling at 125 m/s when...Ch. 14.3 - When s = 0.5 m, the spring is unstretched and the...Ch. 14.3 - The 5-lb collar is pulled by a cord that passes...Ch. 14.3 - The 20-kg crate is subjected to a force having a...Ch. 14.3 - Prob. 2P
Ch. 14.3 - The crate, which has a mass of 100 kg, is...Ch. 14.3 - The 100-kg crate is subjected to the forces shown....Ch. 14.3 - Determine the required height h of the roller...Ch. 14.3 - When the driver applies the brakes of a light...Ch. 14.3 - Prob. 7PCh. 14.3 - Prob. 8PCh. 14.3 - The air spring A is used to protect the support B...Ch. 14.3 - The force F, acting in a constant direction on the...Ch. 14.3 - The force of F= 50 N is applied to the cord when s...Ch. 14.3 - Design considerations for the bumper B on the 5-Mg...Ch. 14.3 - The 2-lb brick slides down a smooth roof, such...Ch. 14.3 - Block A has a weight of 60 lb and block B has a...Ch. 14.3 - The two blocks A and B have weights WA = 60 lb and...Ch. 14.3 - A small box of mass m is given a speed of v=14gr...Ch. 14.3 - Prob. 17PCh. 14.3 - Prob. 18PCh. 14.3 - If the cord is subjected to a constant force of F=...Ch. 14.3 - The crash cushion for a highway barrier consists...Ch. 14.3 - Prob. 21PCh. 14.3 - The 25-lb block has an initial speed of v0 = 10...Ch. 14.3 - The 8-Kg block is moving with an initial speed of...Ch. 14.3 - At a given instant the 10-lb block A is moving...Ch. 14.3 - Prob. 25PCh. 14.3 - The catapulting mechanism is used to propel the...Ch. 14.3 - Prob. 27PCh. 14.3 - The 1 0-lb box falls off the conveyor belt at...Ch. 14.3 - Prob. 29PCh. 14.3 - The 30-lb box A is released from rest and slides...Ch. 14.3 - Prob. 31PCh. 14.3 - The block has a mass of 0.8 kg and moves within...Ch. 14.3 - The 10-lb block is pressed against the spring so...Ch. 14.3 - The spring bumper is used to arrest the motion of...Ch. 14.3 - When the 150-lb skier is at point A he has a speed...Ch. 14.3 - The spring has a stiffness k = 50 lb/ ft and an...Ch. 14.3 - Prob. 37PCh. 14.3 - If the 60-kg skier passes point A with a speed of...Ch. 14.3 - Prob. 39PCh. 14.3 - Prob. 40PCh. 14.3 - Prob. 41PCh. 14.4 - If the contact surface between the 20-kg block and...Ch. 14.4 - Prob. 8FPCh. 14.4 - Prob. 9FPCh. 14.4 - Prob. 10FPCh. 14.4 - Prob. 11FPCh. 14.4 - Prob. 12FPCh. 14.4 - The jeep has a weight of 2500 lb and an engine...Ch. 14.4 - Determine the power Input for a motor necessary to...Ch. 14.4 - An automobile having a mass of 2 Mg travels up a 7...Ch. 14.4 - Prob. 45PCh. 14.4 - To dramatize the loss of energy in an automobile,...Ch. 14.4 - Escalator steps move with a constant speed of 0.6...Ch. 14.4 - Prob. 48PCh. 14.4 - Prob. 49PCh. 14.4 - Determine the power output of the draw-works motor...Ch. 14.4 - The 1000-lb elevator is hoisted by the pulley...Ch. 14.4 - The 50-lb crate is given a speed of 10ft/s in t =...Ch. 14.4 - The sports car has a mass of 2.3 Mg, and while it...Ch. 14.4 - Prob. 54PCh. 14.4 - Prob. 55PCh. 14.4 - The 10-lb collar starts from rest at A and is...Ch. 14.4 - Prob. 57PCh. 14.4 - The 50-lb block rests on the rough surface for...Ch. 14.4 - The escalator steps move with a constant speed of...Ch. 14.4 - If the escalator in Prob.14-46 is not moving,...Ch. 14.4 - Prob. 61PCh. 14.4 - Prob. 62PCh. 14.4 - Prob. 63PCh. 14.4 - Prob. 64PCh. 14.5 - The block has a mass of 150 kg and rests on a...Ch. 14.5 - Prob. 3PPCh. 14.5 - Prob. 4PPCh. 14.5 - The 2-kg pendulum bob is released from rest when...Ch. 14.5 - Prob. 14FPCh. 14.5 - Prob. 15FPCh. 14.5 - Prob. 16FPCh. 14.5 - The 75-lb block is released from rest 5 ft above...Ch. 14.5 - Prob. 18FPCh. 14.5 - The girl has a mass of 40 kg and center of mass at...Ch. 14.5 - The 30-lb block A is placed on top of two nested...Ch. 14.5 - The 5-kg collar has a velocity of 5 m/s to the...Ch. 14.5 - The 5-kg collar has a velocity of 5 m/s to the...Ch. 14.5 - The ball has a weight of 15 lb and is fixed to a...Ch. 14.5 - Prob. 71PCh. 14.5 - The roller coaster car has a mass of 700 kg,...Ch. 14.5 - The roller coaster car has a mass of 700 kg,...Ch. 14.5 - The assembly consists of two blocks A and B which...Ch. 14.5 - Prob. 75PCh. 14.5 - Prob. 76PCh. 14.5 - The roller coaster car having a mass m is released...Ch. 14.5 - The spring has a stiffness k = 200 N/m and an...Ch. 14.5 - Prob. 79PCh. 14.5 - Prob. 80PCh. 14.5 - When s = 0, the spring on the firing mechanism is...Ch. 14.5 - If the mass of the earth is Me, show that the...Ch. 14.5 - A rocket of mass m is fired vertically from the...Ch. 14.5 - The 4-kg smooth collar has a speed of 3 m/s when...Ch. 14.5 - Prob. 85PCh. 14.5 - The skier starts from rest at A and travels down...Ch. 14.5 - Prob. 87PCh. 14.5 - Prob. 88PCh. 14.5 - When the 6-kg box reaches point A it has a speed...Ch. 14.5 - Prob. 90PCh. 14.5 - Prob. 91PCh. 14.5 - The roller coaster car has a speed of 15 ft/s when...Ch. 14.5 - The 10-kg sphere C is released from rest when =...Ch. 14.5 - Prob. 94PCh. 14.5 - The cylinder has a mass of 20 kg and is released...Ch. 14.5 - Prob. 96PCh. 14.5 - A pan of negligible mass is attached to two...Ch. 14.5 - Prob. 1CPCh. 14.5 - Prob. 1RPCh. 14.5 - The small 2-lb collar starting from rest at A...Ch. 14.5 - Prob. 3RPCh. 14.5 - Prob. 4RPCh. 14.5 - Prob. 5RPCh. 14.5 - Prob. 6RPCh. 14.5 - Prob. 7RPCh. 14.5 - Prob. 8RP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Two springs and two masses are attached in a straight vertical line as shown in Figure Q3. The system is set in motion by holding the mass m₂ at its equilibrium position and pushing the mass m₁ downwards of its equilibrium position a distance 2 m and then releasing both masses. if m₁ = m₂ = 1 kg, k₁ = 3 N/m and k₂ = 2 N/m. www.m k₁ = 3 (y₁ = 0). m₁ = 1 k2=2 (y₂ = 0) |m₂ = 1 Y2 y 2 System in static equilibrium (Net change in spring length =32-31) System in motion Figure Q3 - Coupled mass-spring system Determine the equations of motion y₁(t) and y₂(t) for the two masses m₁ and m₂ respectively: Analytically (hand calculations)arrow_forward100 As a spring is heated, its spring constant decreases. Suppose the spring is heated and then cooled so that the spring constant at time t is k(t) = t sin N/m. If the mass-spring system has mass m = 2 kg and a damping constant b = 1 N-sec/m with initial conditions x(0) = 6 m and x'(0) = -5 m/sec and it is subjected to the harmonic external force f(t) = 100 cos 3t N. Find at least the first four nonzero terms in a power series expansion about t = 0, i.e. Maclaurin series expansion, for the displacement: Analytically (hand calculations)arrow_forwardthis is answer to a vibrations question. in the last part it states an assumption of x2, im not sure where this assumption comes from. an answer would be greatly appreciatedarrow_forward
- Please answer with the sketches.arrow_forwardThe beam is made of elastic perfectly plastic material. Determine the shape factor for the cross section of the beam (Figure Q3). [Take σy = 250 MPa, yNA = 110.94 mm, I = 78.08 x 106 mm²] y 25 mm 75 mm I 25 mm 200 mm 25 mm 125 Figure Q3arrow_forwardA beam of the cross section shown in Figure Q3 is made of a steel that is assumed to be elastic- perfectectly plastic material with E = 200 GPa and σy = 240 MPa. Determine: i. The shape factor of the cross section ii. The bending moment at which the plastic zones at the top and bottom of the bar are 30 mm thick. 15 mm 30 mm 15 mm 30 mm 30 mm 30 mmarrow_forward
- A torque of magnitude T = 12 kNm is applied to the end of a tank containing compressed air under a pressure of 8 MPa (Figure Q1). The tank has a 180 mm inner diameter and a 12 mm wall thickness. As a result of several tensile tests, it has been found that tensile yeild strength is σy = 250 MPa for thr grade of steel used. Determine the factor of safety with respect to yeild, using: (a) The maximum shearing stress theory (b) The maximum distortion energy theory T Figure Q1arrow_forwardAn external pressure of 12 MPa is applied to a closed-end thick cylinder of internal diameter 150 mm and external diameter 300 mm. If the maximum hoop stress on the inner surface of the cylinder is limited to 30 MPa: (a) What maximum internal pressure can be applied to the cylinder? (b) Sketch the variation of hoop and radial stresses across the cylinder wall. (c) What will be the change in the outside diameter when the above pressure is applied? [Take E = 207 GPa and v = 0.29]arrow_forwardso A 4 I need a detailed drawing with explanation し i need drawing in solution motion is as follows; 1- Dwell 45°. Plot the displacement diagram for a cam with flat follower of width 14 mm. The required 2- Rising 60 mm in 90° with Simple Harmonic Motion. 3- Dwell 90°. 4- Falling 60 mm for 90° with Simple Harmonic Motion. 5- Dwell 45°. cam is 50 mm. Then design the cam profile to give the above displacement diagram if the minimum circle diameter of the か ---2-125 750 x2.01 98Parrow_forward
- Figure below shows a link mechanism in which the link OA rotates uniformly in an anticlockwise direction at 10 rad/s. the lengths of the various links are OA=75 mm, OB-150 mm, BC=150 mm, CD-300 mm. Determine for the position shown, the sliding velocity of D. A 45 B Space Diagram o NTS (Not-to-Scale) C Darrow_forwardI need a detailed drawing with explanation so Solle 4 يكا Pax Pu + 96** motion is as follows; 1- Dwell 45°. Plot the displacement diagram for a cam with flat follower of width 14 mm. The required 2- Rising 60 mm in 90° with Simple Harmonic Motion. 3- Dwell 90°. 4- Falling 60 mm for 90° with Simple Harmonic Motion. 5- Dwell 45°. cam is 50 mm. Then design the cam profile to give the above displacement diagram if the minimum circle diameter of the 55 ---20125 750 X 2.01 1989arrow_forwardAshaft fitted with a flywheel rotates at 300 rpm. and drives a machine. The torque required to drive the machine varies in a cyclic manner over a period of 2 revolutions. The torque drops from 20,000 Nm to 10,000 Nm uniformly during 90 degrees and remains constant for the following 180 degrees. It then rises uniformly to 35,000 Nm during the next 225 degrees and after that it drops to 20,000 in a uniform manner for 225 degrees, the cycle being repeated thereafter. Determine the power required to drive the machine and percentage fluctuation in speed, if the driving torque applied to the shaft is constant and the mass of the flywheel is 12 tonnes with radius of gyration of 500 mm. What is the maximum angular acceleration of the flywheel. 35,000 TNM 20,000 10,000 0 90 270 495 Crank angle 8 degrees 720arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Dynamics - Lesson 1: Introduction and Constant Acceleration Equations; Author: Jeff Hanson;https://www.youtube.com/watch?v=7aMiZ3b0Ieg;License: Standard YouTube License, CC-BY