(a) Explanation Given information: The discharge ( Q ) of water is 1.2 m 3 / min . The velocity ( v A , v B ) of the water is 30 m / s . The distance between hinge and center of gravity G is 300 mm . The combined mass ( m p ) of the vane and plate is 20 kg . Calculation: Find the mass flow rate using the relation as follows: d m d t = ρ Q (1) Here, d m d t is mass flow rate and ρ is density of water. Substitute 1.2 m 3 / min for Q and 1000 kg / m 3 for ρ in Equation (1). d m d t = ( 1000 kg m 3 ) ( 1.2 m 3 min ) ( 1 min 60 s ) = 20 kg / s Sketch the free body diagram as shown in Figure 1. Refer to Figure 1. Find the angle θ by using impulse momentum principle as follows: Take a moment about C (b) To determine Find the reaction at C .

12th Edition

ISBN: 9781260804638

Author: BEER

Publisher: MCG

See similar textbooks

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Videos

Question

Chapter 14.3, Problem 14.66P

(a)

To determine

Find the angle between the vane and plate (θ).

(b)

To determine

Find the reaction at C.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 14.3, Problem 14.65P

Chapter 14.3, Problem 14.67P

Students have asked these similar questions

Q Derive (continuity equation)? I want to derive clear mathematics.

motor supplies 200 kW at 6 Hz to flange A of the shaft shown in Figure. Gear B transfers 125 W of power to operating machinery in the factory, and the remaining power in the shaft is mansferred by gear D. Shafts (1) and (2) are solid aluminum (G = 28 GPa) shafts that have the same diameter and an allowable shear stress of t= 40 MPa. Shaft (3) is a solid steel (G = 80 GPa) shaft with an allowable shear stress of t = 55 MPa. Determine: a) the minimum permissible diameter for aluminum shafts (1) and (2) b) the minimum permissible diameter for steel shaft (3). c) the rotation angle of gear D with respect to flange A if the shafts have the minimum permissible diameters as determined in (a) and (b).

First monthly exam Gas dynamics Third stage Q1/Water at 15° C flow through a 300 mm diameter riveted steel pipe, E-3 mm with a head loss of 6 m in 300 m length. Determine the flow rate in pipe. Use moody chart. Q2/ Assume a car's exhaust system can be approximated as 14 ft long and 0.125 ft-diameter cast-iron pipe ( = 0.00085 ft) with the equivalent of (6) regular 90° flanged elbows (KL = 0.3) and a muffler. The muffler acts as a resistor with a loss coefficient of KL= 8.5. Determine the pressure at the beginning of the exhaust system (pl) if the flowrate is 0.10 cfs, and the exhaust has the same properties as air.(p = 1.74 × 10-3 slug/ft³, u= 4.7 x 10-7 lb.s/ft²) Use moody chart (1) MIDAS Kel=0.3 Q3/Liquid ammonia at -20°C is flowing through a 30 m long section of a 5 mm diameter copper tube(e = 1.5 × 10-6 m) at a rate of 0.15 kg/s. Determine the pressure drop and the head losses. .μ= 2.36 × 10-4 kg/m.s)p = 665.1 kg/m³

Chapter 14 Solutions

VECTOR MECHANICS FOR ENGINEERS W/CON >B

Ch. 14.1 - A 30-g bullet is fired with a horizontal velocity...Ch. 14.1 - Two identical 1350-kg automobiles A and B are at...Ch. 14.1 - An airline employee tosses two suitcases in rapid...Ch. 14.1 - Car A weighing 4000 lb and car B weighing 3700 lb...Ch. 14.1 - Two swimmers A and B, of weight 190 lb and 125 lb,...Ch. 14.1 - A 180-lb man and a 120-lb woman stand side by side...Ch. 14.1 - A 40-Mg boxcar A is moving in a railroad...Ch. 14.1 - Two identical cars A and B are at rest on a...Ch. 14.1 - A 20-kg base satellite deploys three...Ch. 14.1 - For the satellite system of Prob. 14.9, assuming...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Find the angle between the vane and plate ( θ ) .

Solution Summary: The author explains how to find the angle between the vane and plate using the impulse momentum principle.