
(a)
Find the altitude at which stage A of the rocket is released.
(a)

Answer to Problem 14.102P
The altitude at which stage A of the rocket is released is
Explanation of Solution
Given information:
Consider the initial mass of the rocket is denoted by
The rate of consumption of the fuel is denoted by q.
The velocity of the rocket after time t is denoted by v.
The acceleration due to gravity is denoted by g.
Refer Problem 14.96.
The mass of the rocket is
The mass of the stage A and B is
Show the unit conversion of the mass as follows:
The rate of fuel consumption is
The relative velocity of the rocket is
Calculation:
Show the thrust force (P) of the rocket as follows:
Show the combined mass (m) of the rocket and the unspent fuel as follows:
Show the weight force (W) as follows:
Show the acceleration (a) of the rocket as follows:
Modify Equation (3) using (2) and (1).
Show the velocity of the rocket as follows:
Integrate above Equation with respect to time.
Show the displacement of the rocket as follows:
Integrate above Equation with respect to time.
Consider the value of z as follows:
Differentiate the above Equation with respect to time t.
Consider the value of the
Substitute
Modify Equation (4) using Equation (5) and (6).
Take the lower and upper limit of the integral as
Substitute 1 for
The mass of the fuel is
The velocity of the rocket is
The rate of the fuel consumption is
Calculate the time taken (t) as follows:
Consider the first stage:
The initial velocity and initial distance covered are
Calculate the initial mass of the rocket
Calculate the final velocity of the rocket using the relation:
Substitute 0 for
Calculate the altitude
Substitute 0 for
Thus, the altitude
(b)
Find the altitude at which the fuel of both stages are consumed.
(b)

Answer to Problem 14.102P
The altitude at which the fuel of both stages are consumed is
Explanation of Solution
Given information:
Calculation:
Consider the fuel of both the stages are consumed.
Calculate the final mass
Calculate the altitude
Substitute
Thus, the altitude
Want to see more full solutions like this?
Chapter 14 Solutions
VECTOR MECH...,STAT.+DYN.(LL)-W/ACCESS
- In using the bolt cutter shown, a worker applies two forces P to the handles. If the magnitude ofP is 500 N, determine the magnitude of the forces exerted by the cutter on the boltarrow_forwardArterioles bifurcate (i.e., split) into capillaries in the circulatory system. Blood flows at a velocity of 20 cm/s through an arteriole with a diameter of 0.20 cm. This vessel bifurcates into two vessels: one with a diameter of 0.17 cm and a blood flow velocity of 18 cm/sec, and one with a diameter of 0.15 cm. Each of these two vessels splits again. The 0.17-cm diameter vessel splits into two vessels, each with a diameter of 0.15 cm. The 0.15-cm diameter vessel splits into two vessels, each with a diameter of 0.12 cm. Determine the mass flow rate and velocity of blood in each of the four vessels at the end of the arteriole bifurcations. You may need to set up several systems, each with a different system boundary, in order to solve this problem.arrow_forward6) Draw a Front, side and Top view for the following objects: p.s. you don't need to label the alphabet ISOMETRIC PICTORIAL VIEW K R C B E R D 0 Aarrow_forward
- Please draw the front top and side view for the following objectarrow_forwardDraw the top viewarrow_forwardSuppose that a steel of eutectoid composition is cooled to 675°C (1250°F) from 760°C (1400°F) in less than 0.5 s and held at this temperature. (a) How long will it take for the austenite-topearlite reaction to go to 50% completion? To 100% completion? (b) Estimate the hardness of the alloy that has completely transformed to pearlite.arrow_forward
- Problem 2: Determine the components of the reaction at point B (Please use paper sheet + FBD ,don't use chatgpt) MECHANICAL ENGGarrow_forwardARL040_AE_Kn_2of3... Dor Question 4. A two-throw crankshaft has masses distributed as shown: RAH 90 rpm A TRAV B Re Rev M₁ = 15kg; M₂ = 12kg L = 950mm; 1, 350mm; 1₁ = 600mm; 0₁ = 90°; 02=0°; r₁ = 300mm; r250mm The crankshaft is to be balanced by attaching masses at radii of 300 mm and rotating in planes 150 mm outside the planes of number one and number two cranks. Determine the magnitude and angular position of the balance masses. Answer 4.arrow_forwardFEAarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY





