Materials Science And Engineering Properties
1st Edition
ISBN: 9781111988609
Author: Charles Gilmore
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 14, Problem 5CQ
To determine
The corrosion which causes problem with 316 L stainless steel for human body implants.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What is the chief difference between heat treatable and non-heat-treatable alloys?
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each
Steel
Copper
Area, A
900 mm2
1,200 mm2
Modulus of elasticity, E
200 GPa
120 GPa
ents
Allowable compressive stress
140 MPa
70 MPa
ces
ents
Which of the following most nearly gives the load, in percent, carried by the copper?
ssors
Select the correct response
ication
44.44%
Niki
55.56%
Blogs
66.67%
33.33%
Courses
is low-alloy steel oxidation resistant? if yes, then why?
Chapter 14 Solutions
Materials Science And Engineering Properties
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- Protection from Corrosion Between Dissimilar Metals.arrow_forwardi need quickly please please please Which of these cast iron would allow the greatest amount of plastic deformation before fracture . Nodular cast iron Grey cast iron White cast iron None of them can be worked. If the diameter of steel specimen stretched by tension load is doubled , then it’s tensile strength will be Halved Remain unaffected Doubled Become four times Temperature is proportional with Percent of elongation Tensile strength Modulus of elasticity All above The tensile strength of a steel specimen that have a 182 HB , equals to 490 MPa 910 MPa 627 MPa Not given…arrow_forwardKindly select the correct answer with solutions or explanationsarrow_forward
- Which epoxy resin will be suitable for E-glass Fiberglass that will experience temperatures up to 825 Kelvin?arrow_forward98) What is another name for austenitic stainless steels?A) p91 steelsB) 18-8 steelsC) p92 steelsD) o1 steelsE) h11 steels 99) which is more important for assembly than its values?A) yield strengthB) hardnessC) sizeD) elastic modulusE) wear behavior 100) which is not one of the general properties shown by almost every metal?A) satietyB) high hardness and strengthC) good wear resistanceD) good thermal conductivityE) good electrical conductivityarrow_forwardCivil Engineering A highly alloyed steel commonly referred to as ____________ steel includes chromium, nickel and molybdenum as alloying elements to improve corrosion resistance.arrow_forward
- The frame of a space shuttle type vehicle must have a high yield strength and high stillness, and the most important design factor is weight. Of all the materials presented in this chapter, what material might be the most suitable for the frame of a space shuttle? Assume that there will be both tensile and compressive stresses. For a space shuttle, cost is not a limiting factor. (a) You can eliminate entire classes of materials from consideration with a brief statement about their unsuitability. (b) What material has the highest specific yield strength? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (c) What material has the highest specific elastic modulus? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (d) Compare the materials with the highest specific yield strength and highest specific elastic modulus for suitability in the space shuttle frame. (C) Discuss the suitability of the top-rated material for this design from the viewpoint of the ability to produce a frame.arrow_forwardWhich one of the following types of steel is used in the manufacturing of metro and monorails? A B Mild steel D Cast steel C Manganese steel Bessemer steelarrow_forwardSteel has some fire resistance which is determined by the size of the section, the degree of exposure and the load that it supports. The temperature to failure for steel is directly proportional to the load. The greater the load, the lower the yield or failurearrow_forward
- Is high hardenability desirable in steels? Explain your answer briefly [do not use chatgpt]arrow_forwardd) No increase Which of the following is not a property of steel materials? C a) Homogeneous and isotropic b) Linearly elastic stress-strain behavior c) Recyclable d) Fire-resistantarrow_forwardurgent all three subpart questionarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning
Construction Materials, Methods and Techniques (M...Civil EngineeringISBN:9781305086272Author:William P. Spence, Eva KultermannPublisher:Cengage Learning
Materials Science And Engineering Properties
Civil Engineering
ISBN:9781111988609
Author:Charles Gilmore
Publisher:Cengage Learning
Construction Materials, Methods and Techniques (M...
Civil Engineering
ISBN:9781305086272
Author:William P. Spence, Eva Kultermann
Publisher:Cengage Learning
The History of Iron and Steel; Author: Real Engineering;https://www.youtube.com/watch?v=7E__zqy6xcw;License: Standard Youtube License